110v-230v AC to Mysensors PCB board

tomkxy

How can I check whether the solid state relay works at all. My assembled board receives messages and sets state properly, I have 5V on the pin, however the relay does not seem to switch. Should I hear it? Any other ideas for "debugging"?

GertSanders

@tomkxy
Measure the resistance over the AC terminals of the SSR. It should be very high when "open" en very low when "closed". SSRs do not make sounds when they switch, so sound will not give a clue if they work.

Jan Gatzke

Most SSRs cannot be checked this way because they can only switch AC and not DC. See https://en.wikipedia.org/wiki/Zero_cross_circuit

Cliff Karlsson

I don't know if this has been answered already. But I have some major problems soldering the thermal fuse to the board. It always blows. Any tips ?

sundberg84

@Cliff-Karlsson Be quick :)
I have the same problem - dont know any better sollution atm... solder for 0.5 sec and remove - then you need to let it cool down before adding more solder.

Cliff Karlsson

I read something before about low temp thermal sensors usally being crimped to place. Do you know how this works and if it is usable on the pcb?

Also the last times I tried to assemble the parts on the pcb I noticed that the holes for one of the fuses are too narrow for the standard brown(?) auto reset fuse. I have managed to destroy the solderpads every time I tried to drill the holes a little bigger.
Can I use a standard glass fuse for this one with the same value?

csa02221862

Just a couple of questions. Most of the components are 240V, are these the same as used for 110/120v in the US? Also one of the varistors is not available, suggested alternative?
Thanks

vil1driver

Hi,

thanks for your great work..
great to have chosed a pwm output for the relay (ssr can be used as a dimmer)
but is it possible to add a fuse on the ssr output too ?
and a second switch

and imho relay's trace is too near a nrf trace..
and return the draw of le33 :p

sry for my english
thanks

Sefi Ninio

Hello,

I love your design!
However, I must have missed something. Considering I want to retain the ability to turn the light off with the wall switch, this board does not allow to connect the relay as a 3-way switch.

Also, considering it could be mounted inside the wall (and not only in the lamp base) - having 2-3 relays would be very functional! In my house, it is very common that a single wall mount has 3-4 switches that control 3-4 separate lamps. It will probably make the board bigger, more so if we support 3-way switches (see above comment), but it will be very versatile, especially for 4-way switches (see http://forum.mysensors.org/topic/3173/3-4-way-switch-with-a-relay )

toabhishekverma

Hi Sefi Ninio,
There are two ways you can do it, Either change relay to SPDT Relay which is two way relay. this option is not feasible with this pcb. But if you are not using same PCB you can try SPDT relays.

Second option which can work with this setup is ,
Your light switch has two pins, connect them with gpio and 3.3 power .
when switch turn on/off gpio pin input goes high(when on) and low (when off).
You have to write a code to monitor this gpio and if its state changes, you have to toggle the relay state.

This is my idea, I havent tried it yet. and I am newbie too, Please comment.

I hope I am clear enough

Regards,
Abhishek

Sefi Ninio

Hi, @toabhishekverma
Well, your suggestion might work, I am not sure a switch that is meant to be connected to 220v mains can be connected to the gpio pin.

I think, adding an additional relay to the pcb and allowing them both to behave like a 3way switch will allow for maximum flexibility.

It could control 2 separate lamps
It could behave like 2 3-way switches
It could behave like a single 4-way switch

I would have done it myself, but I have no clue 😀

Cliff Karlsson

I have several lamps where I have done something similar. The bulbs are wireless wemo-bulbs and I have connected the wires behind the lampswitch so that the bulbs are always powered. The I have placed a battery powered arduino witch is connected to the wall switch pin3-gnd.
Every time I flip the switch the arduino wakes up and the controller sends a toggle command using REST

m26872

@Cliff-Karlsson said:

I don't know if this has been answered already. But I have some major problems soldering the thermal fuse to the board. It always blows. Any tips ?

Raise the temperature of your soldering iron, and you'll be able to do it quicker with less propagating heat. You could also add some extra bend and length to the fuse legs.

Sefi Ninio

@Sefi-Ninio said:

Hi, @toabhishekverma
Well, your suggestion might work, I am not sure a switch that is meant to be connected to 220v mains can be connected to the gpio pin.

I think, adding an additional relay to the pcb and allowing them both to behave like a 3way switch will allow for maximum flexibility.

It could control 2 separate lamps

It could behave like 2 3-way switches

It could behave like a single 4-way switch

I would have done it myself, but I have no clue 😀

@aproxx , what do you think about adding another relay (for a total of 2 on board) and making them 3-way?

Cliff Karlsson

Another question about the thermal fuse. I might be wrong on this, but I guess its purpose is to break the power if the HLK overheats. But If placed in the intended place would not the PCB need to be on fire to have the thermal fuse be warmed up to 73 deg C?

HenryWhite

@Cliff-Karlsson said:

Another question about the thermal fuse. I might be wrong on this, but I guess its purpose is to break the power if the HLK overheats. But If placed in the intended place would not the PCB need to be on fire to have the thermal fuse be warmed up to 73 deg C?

I guess you're supposed to glue the thermal fuse to the hlk and run wires from this point to the designated footprint of the fuse on the pcb.

Sefi Ninio

@Sefi-Ninio said:

@Sefi-Ninio said:

Hi, @toabhishekverma
Well, your suggestion might work, I am not sure a switch that is meant to be connected to 220v mains can be connected to the gpio pin.

I think, adding an additional relay to the pcb and allowing them both to behave like a 3way switch will allow for maximum flexibility.

It could control 2 separate lamps

It could behave like 2 3-way switches

It could behave like a single 4-way switch

I would have done it myself, but I have no clue 😀

@aproxx , what do you think about adding another relay (for a total of 2 on board) and making them 3-way?

OK Guys,
I've decided to try and use the original V3.2.3 plans and add another relay to them (with your permission, @aproxx).

The board will have to be a bit bigger, I will have to make room for another relay along side the existing one, and I will have to also make room for its connectors.
Not a big problem, I think, as it is already very well designed and has a small footprint, but still.

I need a bit of help from you guys, though - I am a complete noob when it comes to the wiring and electricity. I can handle the coding, no problem, but the electricity is very new to me.

I am assuming that besides adding the second relay, no other components need to be added - no resistors, capacitors, varistors etc.
Is my assumption correct?

Thanks!

HenryWhite

@Sefi-Ninio said:

I am assuming that besides adding the second relay, no other components need to be added - no resistors, capacitors, varistors etc.
Is my assumption correct?

Thanks!

You need at least a second transistor.

vil1driver

maybe a fuse to protect relay output.. ?
and plz add a second switch, to control an other node or anything..

Sefi Ninio

So basically, I should duplicate the current circuit for the new relay...

110v-230v AC to Mysensors PCB board

17

11.7k

11.2k

113.0k