My sensorboard MYS 1.0beta

[Salmoides]

@novicit, Thanks for the guidance. I just ordered some boards myself, and as a novice, your explanation will be very helpful to me as I plan out my sensors.

[Sorg]

I have seen a MYSBootloader on the github . Is it specificallay related to this Board ?

[hek]

@Sorg

It is an optimized version (very reduced in size) done by the MYSController developer @tekka.

[Joey Edelstein]

@novicit thanks for tips but my problem is I don't really know what all the parts in the kit are. I really need some pictures or video guidance...

[Mrlynx]

@Joey-Edelstein
Now the instruction page is update with some photos.

[jesper]

Hi
Have a question.
if I want to buy YS1.1 pcb + components and YS1.1 pcb . How do I buy so only once shipping?

[Mrlynx]

@jesper Send me an email on robert@sa2avr.se

[Mrlynx]

MYS 1.1 pcb has now got a lower price.
If you by 5 or more boards the price is 2$ / board.
http://www.sa2avr.se/mys-1-1/

[pboye]

@Mrlynx do you have a components list for resistors and capacitors, the schematic shows only r1 c1 not the values.

Per Boye

[Mrlynx]

@pboye look at http://www.sa2avr.se/mys-1-1/ under parts list.

[pboye]

@Mrlynx I ave seen that, but as i se it:

First of all, this is a real nice project.

r1-r4 : ?
r5-r8 : ?
r9-r12 : ?
r13-21 : 4.7 K

part list say's : R1-R21 10×4.7K (472) 4x1K (102) 4x10K (103) 4x120k(124), if you add the numbers it give 22 pices

Per Boye

[Mrlynx]

It all depends on what sensor or actuator you are going to connect.
I chose a basic assortment of resistors to get you started and be able to build all examples on www.mysensors.org.
As this question have come up before am I going to write down some examples on http://www.sa2avr.se

[activemind]

Very useful PCB.
Had a question before placing the order for the pcb.
What is the pitch for the male/female headers and the screw terminals ?
Is it 2.54 mm (0.1") for header and 5.08 mm (0.2") for terminals ?
Thanks

[Mrlynx]

@activemind All headers are 2.54 mm and the screw terminals are 5.0 mm.

[activemind]

Excellent. Thanks for your response.

Also, you mentioned LED driver like PCB. I would be VERY interested in something like that. Do you have a thread which I can follow and maybe add in my cents or two?

-AM

[Mrlynx]

@activemind
No I dont have a thread on the subject yet.
I have a prototype but it contains errors I have to correct before it is useful.

[activemind]

Can you please start a thread on it so that people can take a look at what you are planning and provide input so that it can be generic and useful to a lot of people.

I also have a couple of requests/requirements that I would like to add.

It doesnt make sense to add them here and pollute this thread where that info would be lost.

-AM

[NewFolk]

Hello,
Are everybody ok with 5v arduino and 662k on U1? My sensor node refuse to work.
But on the breadboard everything is ok.
It looks like the problem is in radio power. On breadboard i used 2 different step down convertor board, but both of them was on AMS1117 the power was 3.264 and 3.287.
And on MYS 662k give 3.324. I tried to use capacitors 4.7uF - 100uF, without result.
I also tried to change to another 662k from the pack. But it shows the same result.

Could you give me any suggestion ?
Thank you

send: 1-1-0-0 s=255,c=0,t=18,pt=0,l=5,st=fail:1.4.1
send: 1-1-0-0 s=255,c=3,t=6,pt=1,l=1,st=fail:0
send: 1-1-0-0 s=255,c=3,t=11,pt=0,l=14,st=fail:Relay & Button
send: 1-1-0-0 s=255,c=3,t=12,pt=0,l=3,st=fail:1.0
send: 1-1-0-0 s=1,c=0,t=3,pt=0,l=5,st=fail:1.4.1

[hek]

It is actually your gateway that seems to have problems sending ack back to the node.

[n3ro]

Hey =)

What size are the SMD resistors and stuff?

Regards,
n3ro