Data stored in the EEPROM

Heinz

Chatting about storing data into the EEPROM with @paqor I got a little bit curious what the mysensors library stores into that EEPROM so I wrote a little function for dumping that data. I tested it with the 1.4 version of the library:


void DumpMySensorsEepromData()
{
	Serial.println("Dumping MySensors EEPROM:");
	Serial.println("");

	Serial.print("Node id: ");
	Serial.println(EEPROM.read(EEPROM_NODE_ID_ADDRESS));
	Serial.print("Parent node id: ");
	Serial.println(EEPROM.read(EEPROM_PARENT_NODE_ID_ADDRESS));
	Serial.print("Distance: ");
	Serial.println(EEPROM.read(EEPROM_DISTANCE_ADDRESS));
	Serial.println("");

	// child --> route
	Serial.println("Routing information: ");
	for (int route = EEPROM_ROUTES_ADDRESS; route < EEPROM_CONTROLLER_CONFIG_ADDRESS; route++)
	{
		int child = route - EEPROM_ROUTES_ADDRESS;
		uint8_t destination = EEPROM.read(route);

		if (destination != 0xff)
		{
			Serial.print(child);
			Serial.print(" --> ");
			Serial.print(destination);
			Serial.println("");
		}
	}
	Serial.println("");

	// metric imperial
	Serial.println("Controller config: ");
	uint8_t isMetric = EEPROM.read(EEPROM_CONTROLLER_CONFIG_ADDRESS);
	if (isMetric == 0xFF)
	{
		Serial.println("is metric");
	}
	else
	{
		Serial.println("is imperial");
	}
	Serial.println("");

	Serial.println("Controller config raw data: ");
	for (int config = EEPROM_CONTROLLER_CONFIG_ADDRESS; config < EEPROM_FIRMWARE_TYPE_ADDRESS; config++)
	{
		Serial.print(EEPROM.read(config));
		Serial.print(", ");
		if ((config - EEPROM_CONTROLLER_CONFIG_ADDRESS + 1) % 8 == 0)
		{
			Serial.println("");
		}
	}
	Serial.println("");

	Serial.print("Firmware Type: ");
	Serial.print(EEPROM.read(EEPROM_FIRMWARE_TYPE_ADDRESS + 0));
	Serial.print(", ");
	Serial.println(EEPROM.read(EEPROM_FIRMWARE_TYPE_ADDRESS + 1));
	
	Serial.print("Firmware Version: ");
	Serial.print(EEPROM.read(EEPROM_FIRMWARE_BLOCKS_ADDRESS + 0));
	Serial.print(", ");
	Serial.println(EEPROM.read(EEPROM_FIRMWARE_BLOCKS_ADDRESS + 1));
	
	Serial.print("Firmware Blocks: ");
	Serial.print(EEPROM.read(EEPROM_FIRMWARE_VERSION_ADDRESS + 0));
	Serial.print(", ");
	Serial.println(EEPROM.read(EEPROM_FIRMWARE_VERSION_ADDRESS + 1));
	
	Serial.print("Firmware CRC: ");
	Serial.print(EEPROM.read(EEPROM_FIRMWARE_CRC_ADDRESS + 0));
	Serial.print(", ");
	Serial.println(EEPROM.read(EEPROM_FIRMWARE_CRC_ADDRESS + 1));
	Serial.println("");

	Serial.print("Start of local user config is at address: ");
	Serial.println(EEPROM_LOCAL_CONFIG_ADDRESS);
	Serial.println("");

	Serial.println("Local user data: ");
	for (int localConfig = EEPROM_LOCAL_CONFIG_ADDRESS; localConfig < EEPROM_LOCAL_CONFIG_ADDRESS + 255; localConfig++)
	{
		Serial.print(EEPROM.read(localConfig));
		Serial.print(", ");
		if ((localConfig - EEPROM_LOCAL_CONFIG_ADDRESS + 1) % 8 == 0)
		{
			Serial.println("");
		}
	}
	Serial.println("");
}

The output looks as follows:

Dumping MySensors EEPROM:

Node id: 1
Parent node id: 0
Distance: 1

Routing information:
0 --> 0
1 --> 1
2 --> 100
5 --> 101
65 --> 101
100 --> 100
101 --> 101
102 --> 102
104 --> 100
105 --> 105
106 --> 106
107 --> 107
108 --> 108
109 --> 109
110 --> 110
111 --> 111
112 --> 112
129 --> 101
243 --> 243

Controller config:
is imperial

Controller config raw data:
1, 255, 255, 255, 255, 255, 255, 255,
255, 255, 255, 255, 255, 255, 255, 255,
255, 255, 255, 255, 255, 255, 255, 255,

Firmware Type: 255, 255
Firmware Version: 255, 255
Firmware Blocks: 255, 255
Firmware CRC: 255, 255

Start of local user config is at address: 291

Local user data:
255, 0, 0, 0, 255, 255, 255, 255,
255, 255, 255, 255, 255, 255, 255, 255,
255, 255, 255, 255, 255, 255, 255, 255,
255, 255, 255, 255, 255, 255, 255, 255,
255, 1, 1, 1, 255, 255, 255, 255,
255, 255, 255, 255, 255, 255, 255, 255,
255, 255, 255, 255, 255, 255, 255, 255,
255, 255, 255, 255, 255, 255, 255, 255,
255, 255, 255, 255, 255, 255, 255, 255,
...

The data is from a repeater. Note that the layout may change in upcoming mysensors versions.
Your local data is for example stored at offset 291, so be careful when using the native EEPROM functions where you have to provide an offset!

Heinz

See also
http://forum.mysensors.org/topic/1412/eeprom-usage

m26872

Works good! I made a few minor mods just for my taste, and dumped what I think is from an old gateway v1.4

#include <MySensor.h>
#include <SPI.h>
#include <EEPROM.h>

void setup() {
  Serial.begin(115200);
  DumpMySensorsEepromData();

}

void loop() {}

void printByte(uint8_t b) {
  if (b<100) Serial.print(" ");
  if (b<10) Serial.print(" ");
  Serial.print(b);
  Serial.print(", ");
}

void DumpMySensorsEepromData()
{
    Serial.println("Dumping MySensors EEPROM:");
    Serial.println("");

    Serial.print("Node id (");Serial.print(EEPROM_NODE_ID_ADDRESS);Serial.print(") : ");
    Serial.println(EEPROM.read(EEPROM_NODE_ID_ADDRESS));
    Serial.print("Parent node id (");Serial.print(EEPROM_PARENT_NODE_ID_ADDRESS);Serial.print(") : ");;
    Serial.println(EEPROM.read(EEPROM_PARENT_NODE_ID_ADDRESS));
    Serial.print("Distance (");Serial.print(EEPROM_DISTANCE_ADDRESS);Serial.print(") : ");
    Serial.println(EEPROM.read(EEPROM_DISTANCE_ADDRESS));
    Serial.println("");

    // child --> route
    Serial.print("Routing information (adr ");
    Serial.print(EEPROM_ROUTES_ADDRESS);
    Serial.print(" - ");
    Serial.print(EEPROM_CONTROLLER_CONFIG_ADDRESS-1);
    Serial.println(") :");
    for (int route = EEPROM_ROUTES_ADDRESS; route < EEPROM_CONTROLLER_CONFIG_ADDRESS; route++)
    {
        int child = route - EEPROM_ROUTES_ADDRESS;
        uint8_t destination = EEPROM.read(route);

        if (destination != 0xff)
        {
            Serial.print(child);
            Serial.print(" --> ");
            Serial.print(destination);
            Serial.println("");
        }
    }
    Serial.println("");
    
    // Raw routing data
    Serial.print("Raw routing information (adr ");
    Serial.print(EEPROM_ROUTES_ADDRESS);
    Serial.print(" - ");
    Serial.print(EEPROM_CONTROLLER_CONFIG_ADDRESS-1);
    Serial.println(") :");
        for (int i = EEPROM_ROUTES_ADDRESS; i < EEPROM_CONTROLLER_CONFIG_ADDRESS; i++)
    {
        printByte(EEPROM.read(i));
        //Serial.print(", ");
        if ((i - EEPROM_ROUTES_ADDRESS + 1) % 10 == 0)
        {
            Serial.println("");
        }
    }
    Serial.println("");
    Serial.println("");

    // metric imperial
    Serial.print("Controller config (");Serial.print(EEPROM_CONTROLLER_CONFIG_ADDRESS);Serial.println(") : ");
    uint8_t isMetric = EEPROM.read(EEPROM_CONTROLLER_CONFIG_ADDRESS);
    if (isMetric == 0xFF)
    {
        Serial.println("is metric");
    }
    else
    {
        Serial.println("is imperial");
    }
    Serial.println("");

    Serial.print("Controller config raw data (adr ");
    Serial.print(EEPROM_CONTROLLER_CONFIG_ADDRESS);
    Serial.print(" - ");
    Serial.print(EEPROM_FIRMWARE_TYPE_ADDRESS-1);
    Serial.println(") :");
    for (int config = EEPROM_CONTROLLER_CONFIG_ADDRESS; config < EEPROM_FIRMWARE_TYPE_ADDRESS; config++)
    {
        printByte(EEPROM.read(config));
        //Serial.print(", ");
        if ((config - EEPROM_CONTROLLER_CONFIG_ADDRESS + 1) % 10 == 0)
        {
            Serial.println("");
        }
    }
    Serial.println("");
    Serial.println("");

    Serial.print("Firmware Type (adr ");
    Serial.print(EEPROM_FIRMWARE_TYPE_ADDRESS);
    Serial.print(" - ");
    Serial.print(EEPROM_FIRMWARE_TYPE_ADDRESS+1);
    Serial.println(") :");
    Serial.print(EEPROM.read(EEPROM_FIRMWARE_TYPE_ADDRESS + 0));
    Serial.print(", ");
    Serial.println(EEPROM.read(EEPROM_FIRMWARE_TYPE_ADDRESS + 1));
        
    Serial.print("Firmware Blocks (adr ");
    Serial.print(EEPROM_FIRMWARE_VERSION_ADDRESS);
    Serial.print(" - ");
    Serial.print(EEPROM_FIRMWARE_VERSION_ADDRESS+1);
    Serial.println(") :");
    Serial.print(EEPROM.read(EEPROM_FIRMWARE_VERSION_ADDRESS + 0));
    Serial.print(", ");
    Serial.println(EEPROM.read(EEPROM_FIRMWARE_VERSION_ADDRESS + 1));
    
    Serial.print("Firmware Version (adr ");
    Serial.print(EEPROM_FIRMWARE_BLOCKS_ADDRESS);
    Serial.print(" - ");
    Serial.print(EEPROM_FIRMWARE_BLOCKS_ADDRESS+1);
    Serial.println(") :");
    Serial.print(EEPROM.read(EEPROM_FIRMWARE_BLOCKS_ADDRESS + 0));
    Serial.print(", ");
    Serial.println(EEPROM.read(EEPROM_FIRMWARE_BLOCKS_ADDRESS + 1));
    
    Serial.print("Firmware CRC (adr ");
    Serial.print(EEPROM_FIRMWARE_CRC_ADDRESS);
    Serial.print(" - ");
    Serial.print(EEPROM_FIRMWARE_CRC_ADDRESS+1);
    Serial.println(") :");
    Serial.print(EEPROM.read(EEPROM_FIRMWARE_CRC_ADDRESS + 0));
    Serial.print(", ");
    Serial.println(EEPROM.read(EEPROM_FIRMWARE_CRC_ADDRESS + 1));
    Serial.println("");

    Serial.print("Start of local user config is at address: ");
    Serial.println(EEPROM_LOCAL_CONFIG_ADDRESS);
    Serial.println("");

    Serial.print("Local user data (adr ");
    Serial.print(EEPROM_LOCAL_CONFIG_ADDRESS);
    Serial.print(" - ");
    Serial.print(EEPROM_LOCAL_CONFIG_ADDRESS+255);
    Serial.println(") :");
    for (int localConfig = EEPROM_LOCAL_CONFIG_ADDRESS; localConfig < EEPROM_LOCAL_CONFIG_ADDRESS + 255; localConfig++)
    {
        printByte(EEPROM.read(localConfig));
        //Serial.print(", ");
        if ((localConfig - EEPROM_LOCAL_CONFIG_ADDRESS + 1) % 10 == 0)
        {
            Serial.println("");
        }
    }
    Serial.println("");
}

Output example:

Dumping MySensors EEPROM:

Node id (0) : 255
Parent node id (1) : 255
Distance (2) : 255

Routing information (adr 3 - 258) :
16 --> 16
17 --> 50
101 --> 50
102 --> 50
104 --> 50
105 --> 105
106 --> 106
110 --> 110

Raw routing information (adr 3 - 258) :
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255,  16,  50, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255,  50,  50, 255,  50, 105, 106, 255, 255, 255, 
110, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 

Controller config (259) : 
is metric

Controller config raw data (adr 259 - 282) :
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 

Firmware Type (adr 283 - 284) :
255, 255
Firmware Blocks (adr 285 - 286) :
255, 255
Firmware Version (adr 287 - 288) :
255, 255
Firmware CRC (adr 289 - 290) :
255, 255

Start of local user config is at address: 323

Local user data (adr 323 - 578) :
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 
255, 255, 255, 255, 255,

Heinz

Thanks, looks good.

Data stored in the EEPROM

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Gateways
Development • esp8266 raspberry pi serial gateway nano rpi tcp gateway mqtt gateway • • OldSurferDude

LAN8720A - will mysensors work with this module
Development • • Marcin

Serial Gateway woes
Development • • OldSurferDude

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

10
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Data stored in the EEPROM

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

Gateways Development • esp8266 raspberry pi serial gateway nano rpi tcp gateway mqtt gateway • • OldSurferDude

LAN8720A - will mysensors work with this module Development • • Marcin

Serial Gateway woes Development • • OldSurferDude

MYSController with MQTT Gateway (via Node Red) Development • • slt1

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000' Development • • kiesel

10Online

11.4kUsers

11.1kTopics

112.7kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Gateways
Development • esp8266 raspberry pi serial gateway nano rpi tcp gateway mqtt gateway • • OldSurferDude

LAN8720A - will mysensors work with this module
Development • • Marcin

Serial Gateway woes
Development • • OldSurferDude

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

10
Online

11.4k
Users

11.1k
Topics

112.7k
Posts