Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

MySensors 1.5.4 Released

Anticimex Contest Winner last edited by

We are happy to announce a maintenance release of MySensors library to 1.5.4!

This version is backward compatible with 1.5.3 and contain a bugfix that prevented certain payload "getters" from working properly in some situations.
Reply Quote 0
1 Reply Last reply

1
Posts

2127
Views

Suggested Topics

Missing Notification Settings
Bug Reports • • edoardoo

3

0
Votes

3
Posts

1774
Views

@edoardoo There is an little "eye"-button in to top bar of first message in each thread. Press it to get notified when a new message is posted.
Merry Christmas and Happy New 2023
Announcements • • mfalkvidd

2

4
Votes

2
Posts

27
Views

thank you .... and a happy new year to MySensors users
💬 Real Time Clock Module, LCD Display and Controller Time
Announcements • • hek

10

0
Votes

10
Posts

2851
Views

... compiled: Jan 27 202312:42:11 01/27/2023 12:42:11 RTC lost confidence in the DateTime! RTC is the same as compile time! (not expected but all is fine) 01/27/2023 12:42:11 19.25C 01/27/2023 12:42:14 19.25C -------- power loss ----- RTC communications error = 4 01/01/2000 00:00:00 0.00C RTC communications error = 5 01/01/2000 00:00:00 0.00C.. ------------- return power supply +5v ---- RTC lost confidence in the DateTime! 01/01/2000 00:00:12 19.50C RTC lost confidence in the DateTime! 01/01/2000 00:00:15 19.50C ... https://forum.arduino.cc/t/librairie-makuna-freez/1081415/34
💬 Battery Powered Sensors
Announcements • battery • • hek

347

0
Votes

347
Posts

66933
Views

@nekitoss I used 3.3V pro mini with regulator removed and powered by Vin pin. Also removed leds from the pro mini. I used minicore bootloader. I used the small pir sensors and again removed the regulator to power directly from the pro mini outputs. After that sleep the node and trigger on interrupt. Send battery level once a day. Use inbuilt battery level monitor and not external components that constantly drain power to get battery level. 1.8V is 0% on the graph (not visible yet!) but I have had nodes working below 1.7V It's a matter of luck with that it seems. Hope this helps you on the right track. I'll try and help if you want. This is the latest image and still going strong after 18 months. Voltage is at 2.903V Here is photo of the test example - I need to make a case and produce more of them over winter..... Here is the same build/code of a window sensor. Similar time frame but hardly triggered.....
💬 Components
Announcements • • hek

7

0
Votes

7
Posts

1061
Views

@GLAB said in Components: nrf24l01+ I have run the RF24 libraries in 230kbs and that worked for me. I cannot confirm MySensors, but I would assume "yes" OSD
💬 Building a Orange Pi Gateway
Announcements • • hek

110

0
Votes

110
Posts

31599
Views

I saw this page and thought I give it a go. So I bought two OrangePi Zero 2. There's a lot of potential (WiFi) as a dedicated gateway. Currently the price is about US$20 on AliExpress (caveat emptor) There are a few flavors of Linux for it. I've dabbled with Armbian, Ubuntu and Debian Another upside is that it doesn't draw a lot of current ~0.5A, though I haven't been successful in getting the radio to run (the reason for me being here) This is also a downside as I suspect the power supply needs to be very close to 5V. Thinking it was a power hog like the RPi, I used a 5V-3A supply. This supply operates on the principle that the load will pull down the voltage. There are dire warnings on the orangepi page about using cheap SD cards, but failed to mention that power supplies have to be matched, too. It has a different CPU than the Orange Pi Zero non-2, the board that is used here. Use the serial interface to configure the board. You're going to be doing all your configuration in a terminal, anyway, so you don't need a monitor or a keyboard. https://www.instructables.com/Setup-Orange-Pi-Using-Serial-Port/ The big downside is that the SPI interface is not supported. My research indicates that in order to get it to work one must jump through some serious hoops and being low on the learning curve, those hoops are probably out of my reach. https://forum.armbian.com/topic/21688-tips-on-configuring-double-spi-through-two-chipselects-on-orange-pi-zero-2/ The armbian OS has another big downside, WiFi is not supported. Putting a TP-Link nano router configured as a client works, but it's another $30! Why did they even release the OS? So! Was anyone successful in getting the Orange Pi Zero 2 configured as a gateway?

MySensors 1.5.4 Released

Suggested Topics

Missing Notification Settings
Bug Reports • • edoardoo

Merry Christmas and Happy New 2023
Announcements • • mfalkvidd

💬 Real Time Clock Module, LCD Display and Controller Time
Announcements • • hek

💬 Battery Powered Sensors
Announcements • battery • • hek

💬 Components
Announcements • • hek

💬 Building a Orange Pi Gateway
Announcements • • hek

38
Online

11.5k
Users

11.1k
Topics

112.7k
Posts

MySensors 1.5.4 Released

Suggested Topics

Missing Notification Settings Bug Reports • • edoardoo

Merry Christmas and Happy New 2023 Announcements • • mfalkvidd

💬 Real Time Clock Module, LCD Display and Controller Time Announcements • • hek

💬 Battery Powered Sensors Announcements • battery • • hek

💬 Components Announcements • • hek

💬 Building a Orange Pi Gateway Announcements • • hek

38Online

11.5kUsers

11.1kTopics

112.7kPosts

Missing Notification Settings
Bug Reports • • edoardoo

Merry Christmas and Happy New 2023
Announcements • • mfalkvidd

💬 Real Time Clock Module, LCD Display and Controller Time
Announcements • • hek

💬 Battery Powered Sensors
Announcements • battery • • hek

💬 Components
Announcements • • hek

💬 Building a Orange Pi Gateway
Announcements • • hek

38
Online

11.5k
Users

11.1k
Topics

112.7k
Posts