12v Solar battery monitor

[Boots33]

If you are still using the 20v divider, with a battery voltage of 13.09 you should have a voltage of 3.27 at pin A0

1.055v is way too low, check you connections to make sure they are tight. measure the voltage at the divider input to make sure the 13v is there as well.

post results again

[mrc-core]

3.29v It's the value i'm getting at the end off the 20v divider but at pin A0 i have 1.23V

Requesting temperatures...
sum count...198
mapped volts...3.9
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:3.9
Milliamps...200
send: 6-6-3-0 s=4,c=1,t=39,pt=7,l=5,sg=0,st=ok:0.2
send: 6-6-3-0 s=5,c=1,t=39,pt=2,l=2,sg=0,st=ok:0
Requesting temperatures...
sum count...511
mapped volts...10.0
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:10.0
Milliamps...126
send: 6-6-3-0 s=4,c=1,t=39,pt=7,l=5,sg=0,st=ok:0.1
send: 6-6-3-0 s=5,c=1,t=39,pt=2,l=2,sg=0,st=ok:0
Requesting temperatures...
sum count...511
mapped volts...10.0
Milliamps...-21
send: 6-6-3-0 s=4,c=1,t=39,pt=2,l=2,sg=0,st=ok:0
send: 6-6-3-0 s=5,c=1,t=39,pt=7,l=5,sg=0,st=fail:0.0
Requesting temperatures...
sum count...520
mapped volts...10.2
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:10.2
Milliamps...126
send: 6-6-3-0 s=4,c=1,t=39,pt=7,l=5,sg=0,st=ok:0.1
send: 6-6-3-0 s=5,c=1,t=39,pt=2,l=2,sg=0,st=fail:0
Requesting temperatures...
sum count...533
mapped volts...10.4
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:10.4
Milliamps...52
send: 6-6-3-0 s=4,c=1,t=39,pt=7,l=5,sg=0,st=ok:0.1
send: 6-6-3-0 s=5,c=1,t=39,pt=2,l=2,sg=0,st=ok:0
Requesting temperatures...
sum count...511
mapped volts...10.0
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:10.0
Milliamps...-21
send: 6-6-3-0 s=4,c=1,t=39,pt=2,l=2,sg=0,st=ok:0
send: 6-6-3-0 s=5,c=1,t=39,pt=7,l=5,sg=0,st=ok:0.0
Requesting temperatures...
sum count...511
mapped volts...10.0
Milliamps...200
send: 6-6-3-0 s=4,c=1,t=39,pt=7,l=5,sg=0,st=ok:0.2
send: 6-6-3-0 s=5,c=1,t=39,pt=2,l=2,sg=0,st=ok:0
Requesting temperatures...

[Boots33]

then that is where the problem may be. the output of the divider should be connected to A0 so they should be the same. look at the diagram below

[mrc-core]

I think the problem is fix now.

bad cable between ground from 20v divider and arduino ground.
now i'm getting the same value at pin a0

here are the new logs

send: 6-6-3-0 s=255,c=3,t=11,pt=0,l=21,sg=0,st=ok:Battery Status Sensor
send: 6-6-3-0 s=255,c=3,t=12,pt=0,l=1,sg=0,st=ok:1
send: 6-6-3-0 s=0,c=0,t=6,pt=0,l=0,sg=0,st=ok:
send: 6-6-3-0 s=1,c=0,t=6,pt=0,l=0,sg=0,st=fail:
send: 6-6-3-0 s=3,c=0,t=38,pt=0,l=0,sg=0,st=fail:
send: 6-6-3-0 s=4,c=0,t=39,pt=0,l=0,sg=0,st=fail:
send: 6-6-3-0 s=5,c=0,t=39,pt=0,l=0,sg=0,st=ok:
sum count...715
mapped volts...14.0
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:14.0
Milliamps...-21
send: 6-6-3-0 s=4,c=1,t=39,pt=2,l=2,sg=0,st=ok:0
send: 6-6-3-0 s=5,c=1,t=39,pt=7,l=5,sg=0,st=ok:0.0
Requesting temperatures...
send: 6-6-3-0 s=0,c=1,t=0,pt=7,l=5,sg=0,st=ok:29.3
send: 6-6-3-0 s=1,c=1,t=0,pt=7,l=5,sg=0,st=ok:-127.0
sum count...710
mapped volts...13.9
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:13.9
Milliamps...52
send: 6-6-3-0 s=4,c=1,t=39,pt=7,l=5,sg=0,st=ok:0.1
send: 6-6-3-0 s=5,c=1,t=39,pt=2,l=2,sg=0,st=ok:0
Requesting temperatures...
sum count...713
mapped volts...13.9
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:13.9
Milliamps...-21
send: 6-6-3-0 s=4,c=1,t=39,pt=2,l=2,sg=0,st=ok:0
send: 6-6-3-0 s=5,c=1,t=39,pt=7,l=5,sg=0,st=ok:0.0
Requesting temperatures...
sum count...711
mapped volts...13.9
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:13.9
Milliamps...200
send: 6-6-3-0 s=4,c=1,t=39,pt=7,l=5,sg=0,st=ok:0.2
send: 6-6-3-0 s=5,c=1,t=39,pt=2,l=2,sg=0,st=ok:0
Requesting temperatures...
sum count...712
mapped volts...13.9
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:13.9
Milliamps...200
Requesting temperatures...
sum count...709
mapped volts...13.9
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:13.9
Milliamps...126
send: 6-6-3-0 s=4,c=1,t=39,pt=7,l=5,sg=0,st=ok:0.1
send: 6-6-3-0 s=5,c=1,t=39,pt=2,l=2,sg=0,st=ok:0
Requesting temperatures...
sum count...713
mapped volts...13.9
send: 6-6-3-0 s=3,c=1,t=38,pt=7,l=5,sg=0,st=ok:13.9
Milliamps...126
Requesting temperatures...

still using the cpu fan 12v 0.25A pin A0 3.28V
Mapped volts 13.9 it's very near the 13.2V the multimeter gives at the battery.
This is the best results i had until now.

Thanks boots33 for all your help.

[Boots33]

Great to hear you have found the problem. If the voltages are not quite correct you can adjust the 20000 value up or down a bit as needed to fine tune the output result.

You can use these to check for the problem

for a 20v divider

20/1024 = .019531

to get the count that should be shown by serial print...: batteryvoltage / .019531

so with your reading 13.09 / .019531 = 670
That means you should see a count of 670 from the serial print

to get the voltage that should be at pin A0...: count * .00488

670 * .00488 = 3.27v

to get the map result

20000/1024 = 19.531mv or .01953v

so 670 * .01953 = 13.1v

[Boots33]

The best way to setup the acs712 is to put it where it is going to be mounted but have no current going through it. (you can just disconnect one power lead) it should show a reading close to zero.
If not push the button and hold till the led flashes (may take a while depending on how much delay you are using) once the led flashes you can let go of the button and the offset to zero the reading will be applied. This offset will also be saved in the arduino eeprom so it will be reloaded if the arduino is rebooted etc.
then the readings should be very close to zero.
you can now reconnect and it should give you the correct reading.

[aDm1N]

Hallo

Mein Englisch ist nicht so gut.
Ich habe versucht das Projekt nach zu bauen. Den Button brauche ich (denke ich) nicht, dafür habe ich das script jedoch um 2 weitere current und voltage Sensoren erweitert. Das Ziel ist 3 mal Current und 3 mal Volt als Ergebnis zu bekommen. Ich habe 30A Sensoren und einen 30A Laderegler. Dazwischen sind jeweils 30A Sicherungen.
Leider kommt in Domoticz aber nur ein mal Volt und 2 mal Current an. Leider habe ich auch nicht wirklich viel Ahnung vom Programmieren. Könnte hier mal jemand über den Sketch gucken um zu sehen ob ich einen Fehler darin habe?

/*Sketch for a MySensor node to monitor a 12v battery with a solar panel for charging
 * The node monitors battery voltage,current into and out of the battery, ambient temperature and battery temperature.
 * 2 x DS18b20 dallas temperature ic's their data pins connected to arduino digital pin 3
 * 1 x ACS712 current sensor module connected to  arduino analog pin A4
 * 1 x 25v voltage sensor module connected to arduino analog pin A0
 * 1 x nRF24L01+  2.4ghz tranceiver connected as per the MySensors web site.
 * 1 x LED connected via a 330 ohm resistor to pin 6
 * 1 x push button connected to pin 5
 */
 
#include <MySensor.h>  
#include <SPI.h>
#include <OneWire.h>
#include <DallasTemperature.h>
 

#define ONE_WIRE_BUS 3                       // Ds18b20 data wire is connected to digital pin 3 on the Arduino
#define ID_S_TEMPA 0                         // First temp device
#define ID_S_TEMPB 1                         // second temp device
#define ID_S_MULTIMETERV1 3                   // Multimeter device for voltage measurement
#define ID_S_MULTIMETERC1 4                   // Multimeter device for positive current measurement 
#define ID_S_MULTIMETERC11 5                  // Multimeter device for negative current measurement
#define ID_S_MULTIMETERV2 3                   // Multimeter device for voltage measurement
#define ID_S_MULTIMETERC2 4                   // Multimeter device for positive current measurement 
#define ID_S_MULTIMETERC12 5                  // Multimeter device for negative current measurement
#define ID_S_MULTIMETERV3 6                   // Multimeter device for voltage measurement
#define ID_S_MULTIMETERC3 7                   // Multimeter device for positive current measurement 
#define ID_S_MULTIMETERC13 8
#define NUM_SAMPLES 10                       // number of analog voltage samples to take per reading


int ledPin = 6;                               // the pin for the LED
int buttonPin = 5;                            // the input pin for offset pushbutton
int buttonState = 0;                          // variable for reading the pin status
unsigned long SLEEP_TIME = 30000;            // Sleep time between reads (in milliseconds)
int lastmilli1 = 25000;                       // set to an arbitary number outside of expected current sensor range to ensure a change when first run 
int lastmilli2 = 25000;                       // set to an arbitary number outside of expected current sensor range to ensure a change when first run 
int lastmilli3 = 25000;                       // set to an arbitary number outside of expected current sensor range to ensure a change when first run 
float sensitivity = 66 ;                    //change this to 185 for ACS712-5 or to 100 for ACS712-20A or to 66 for ACS712-30A
int VQ = 0;                                  //Placeholder for quiescent voltage calculations
int ACSPin1 = A4;                             // Analog pin number the ACS712 data pin connects to
int ACSPin2 = A5;                             // Analog pin number the ACS712 data pin connects to
int ACSPin3 = A3;                             // Analog pin number the ACS712 data pin connects to
float lastTemperature[2];                    //Array to hold the last temp readings sent to gateway, only send new data if different
int sum = 0;                                 // sum of voltage samples taken
unsigned char sample_count = 0;              // current sample number
int lastVoltage1 = 30000;                     // set to an arbitary number outside of expected voltage sensor range to ensure a change when first run
int lastVoltage2 = 30000;                     // set to an arbitary number outside of expected voltage sensor range to ensure a change when first run
int lastVoltage3 = 30000;                     // set to an arbitary number outside of expected voltage sensor range to ensure a change when first run
int voltagePin1 = A0;                         // analog pin voltage sensor or voltage divider is connected to
int voltagePin2 = A1;                         // analog pin voltage sensor or voltage divider is connected to
int voltagePin3 = A2;                         // analog pin voltage sensor or voltage divider is connected to
int voltSense1Max = 25000;                    // set to the maximum input voltage in millivolts of your voltage divider input  
int voltSense2Max = 25000;                    // set to the maximum input voltage in millivolts of your voltage divider input
int voltSense3Max = 25000;                    // set to the maximum input voltage in millivolts of your voltage divider input    
OneWire oneWire(ONE_WIRE_BUS);               // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire);         // Pass our oneWire reference to Dallas Temperature.

MySensor gw;

// ------ Initialize  messages -------
MyMessage msg(0,V_TEMP);                     
MyMessage msg_S_MULTIMETERv1(ID_S_MULTIMETERV1,V_VOLTAGE);
MyMessage msg_S_MULTIMETERc1(ID_S_MULTIMETERC1,V_CURRENT);
MyMessage msg_S_MULTIMETERc11(ID_S_MULTIMETERC11,V_CURRENT); 
MyMessage msg_S_MULTIMETERv2(ID_S_MULTIMETERV2,V_VOLTAGE);
MyMessage msg_S_MULTIMETERc2(ID_S_MULTIMETERC2,V_CURRENT);
MyMessage msg_S_MULTIMETERc12(ID_S_MULTIMETERC12,V_CURRENT); 
MyMessage msg_S_MULTIMETERv3(ID_S_MULTIMETERV3,V_VOLTAGE);
MyMessage msg_S_MULTIMETERc3(ID_S_MULTIMETERC3,V_CURRENT);
MyMessage msg_S_MULTIMETERc13(ID_S_MULTIMETERC13,V_CURRENT); 

void setup()
{
 
sensors.begin();                                    // Start up the onewire library
gw.begin();                                         // Startup and initialize MySensors library. Set callback for incoming messages. 
gw.sendSketchInfo("Battery Status Sensor", "1");    // Send the sketch version information to the gateway and Controller

// ------ Present all sensors to controller ------
gw.present(ID_S_TEMPA, S_TEMP);
gw.present(ID_S_TEMPB, S_TEMP);
gw.present(ID_S_MULTIMETERV1,V_VOLTAGE);
gw.present(ID_S_MULTIMETERC1,V_CURRENT);
gw.present(ID_S_MULTIMETERC11,V_CURRENT);
gw.present(ID_S_MULTIMETERV2,V_VOLTAGE);
gw.present(ID_S_MULTIMETERC2,V_CURRENT);
gw.present(ID_S_MULTIMETERC12,V_CURRENT);
gw.present(ID_S_MULTIMETERV3,V_VOLTAGE);
gw.present(ID_S_MULTIMETERC3,V_CURRENT);
gw.present(ID_S_MULTIMETERC13,V_CURRENT);


pinMode(buttonPin, INPUT_PULLUP);                     // Set buttonPin as input and turn on internal pull up resistor
pinMode(ledPin, OUTPUT);                              // Set ledPin as output
digitalWrite(ledPin, LOW);                            // Make sure ledPin is off

// ------ load offset for current sensor
int validCheck = gw.loadState(0);
if (validCheck == 120){                          // check to see if valid data exists
  VQ = gw.loadState(1);                               // Load count offset into VQ
//  Serial.print(" positive VQ offset loaded..."); Serial.println(VQ);
 }
 else if (validCheck == 125) {
  VQ = -abs(gw.loadState(1));
//  Serial.print(" negative VQ offset loaded..."); Serial.println(VQ);
 }
else {
// Serial.println("VQ offset not set");
}

delay(500);  
}
 
void loop()
{

buttonState = digitalRead(buttonPin);
//Serial.print("buttonstate..."); Serial.println(buttonState);
 if (buttonState == LOW) {
    VQ = determineVQ(ACSPin1);                           //Returns the offset count needed to show zero with no load

    
  if (VQ >= 0 && VQ < 255) {                              //check for valid data. VQ is positive number
    gw.saveState(0, 120);                               // Store 120 value  in eeprom position 0. use this to check for valid data at boot
    gw.saveState(1, VQ);                                // Store offset count in eeprom. in case of re-boot  
  }
  else if (VQ < 0 && VQ > -255) {                              // VQ is a negative number. negatives cannot be stored in eeprom
    gw.saveState(0, 125);                               // Store 125 value  in eeprom position 0. use this to check for valid data at boot
    gw.saveState(1, abs(VQ));                                // convert VQ to positive and  Store offset count in eeprom. in case of re-boot   
  }

  }

// ------------------ Start voltage 1 readings --------------------
 

 sample_count = 0;
 sum = 0;
 while (sample_count < NUM_SAMPLES) {                                   // take a number of voltage samples  
  sum += analogRead(voltagePin1);
  sample_count++;
  delay(10);
 }
//Serial.print("sum count..."); Serial.println((sum / NUM_SAMPLES));      // print the count result. will be between 0 and 1023
int voltage1I = map(sum/NUM_SAMPLES,0,1023,0,voltSense1Max);              // map the reading and get our result in millivolts
//Serial.print("mapped volts..."); Serial.println(voltageI / 1000.0, 1);  // convert millivolts back to volts and print. the 1 at the end determines how many decimal places to show


if ( voltage1I != lastVoltage1) {                                         // check if we have a new value. only send data if it is different
 gw.send(msg_S_MULTIMETERv1.set(voltage1I / 1000.0, 1));                  // voltagel is in millivolts so we divide by 1000 to convert back to volts and
                                                                        // send voltage message to gateway with 1 decimal place
 lastVoltage1 = voltage1I;                                                // copy the current voltage reading for testing on the next loop 
}

//--------------------Start Current 1 readings---------------------------------

int milli1 = readCurrent(ACSPin1);                                       // take a reading from the ACS712 and send to the readcurrent function

//Serial.print("Milliamps..."); Serial.println(milli);                   // print the value (in milliamps) returned

if ( milli1 != lastmilli1)                                               // check if value has changed
{
 if ( milli1 > 0)                                                       // Battery is charging
 {
  gw.send(msg_S_MULTIMETERc1.set(milli1/1000.0, 1));                     // Send new data to charging amp device
  gw.send(msg_S_MULTIMETERc11.set(0));                                  // set the dis-charging amp device to zero
  lastmilli1 =  milli1;
 }
 else if (milli1 < 0)                                                  // Battery is discharging
 {
  gw.send(msg_S_MULTIMETERc1.set(0));                                  // set the charging amp device to zero
  gw.send(msg_S_MULTIMETERc11.set(abs(milli1)/1000.0, 1));             //  use abs(milli) to Send a positive number  to dis-charging amp device
  lastmilli1 =  milli1; 
 }
else                                                                // No current flowing, set both to zero
{
 gw.send(msg_S_MULTIMETERc1.set(0));
 gw.send(msg_S_MULTIMETERc11.set(0));
 lastmilli1 =  milli1;
}
}
 
//----------------------Teperature readings start------------------------
  
  Serial.println(" Requesting temperatures...");
 
 // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();                  // call sensors.requestTemperatures() to issue a global temperature request to all devices on the bus

  // ------- query conversion time and sleep until conversion completed ------
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  gw.sleep(conversionTime);

 for (int i=0; i<2; i++) {
//  Serial.print("Temperature for Device: ");Serial.print(i);Serial.print(" is: ");
 // Serial.println(sensors.getTempCByIndex(i)); // Why "byIndex"? 
    // You can have more than one IC on the same bus. 
    // 0 refers to the first IC on the wire

 float temperature = static_cast<float>(static_cast<int>((sensors.getTempCByIndex(i)) * 10.)) / 10.;  // Fetch and round temperature to one decimal in celcius

if (lastTemperature[i] != temperature)               // check for a changed temperature reading
  {
   gw.send(msg.setSensor(i).set(temperature,1));     // Send in the new temperature
   lastTemperature[i]=temperature;                   // Save new temperatures for next compare
  }     
}

// ------------------ Start 2 voltage readings --------------------
 

 sample_count = 0;
 sum = 0;
 while (sample_count < NUM_SAMPLES) {                                   // take a number of voltage samples  
  sum += analogRead(voltagePin2);
  sample_count++;
  delay(10);
 }
//Serial.print("sum count..."); Serial.println((sum / NUM_SAMPLES));      // print the count result. will be between 0 and 1023
int voltage2I = map(sum/NUM_SAMPLES,0,1023,0,voltSense2Max);              // map the reading and get our result in millivolts
//Serial.print("mapped volts..."); Serial.println(voltageI / 1000.0, 1);  // convert millivolts back to volts and print. the 1 at the end determines how many decimal places to show


if ( voltage2I != lastVoltage2) {                                         // check if we have a new value. only send data if it is different
 gw.send(msg_S_MULTIMETERv2.set(voltage2I / 1000.0, 1));                  // voltagel is in millivolts so we divide by 1000 to convert back to volts and
                                                                        // send voltage message to gateway with 1 decimal place
 lastVoltage2 = voltage2I;                                                // copy the current voltage reading for testing on the next loop 
}

//--------------------Start Current 2 readings---------------------------------

int milli2 = readCurrent(ACSPin2);                                       // take a reading from the ACS712 and send to the readcurrent function

//Serial.print("Milliamps..."); Serial.println(milli);                   // print the value (in milliamps) returned

if ( milli2 != lastmilli2)                                               // check if value has changed
{
 if ( milli2 > 0)                                                       // Battery is charging
 {
  gw.send(msg_S_MULTIMETERc2.set(milli2/1000.0, 1));                     // Send new data to charging amp device
  gw.send(msg_S_MULTIMETERc12.set(0));                                  // set the dis-charging amp device to zero
  lastmilli2 =  milli2;
 }
 else if (milli1 < 0)                                                  // Battery is discharging
 {
  gw.send(msg_S_MULTIMETERc2.set(0));                                  // set the charging amp device to zero
  gw.send(msg_S_MULTIMETERc12.set(abs(milli2)/1000.0, 1));             //  use abs(milli) to Send a positive number  to dis-charging amp device
  lastmilli2 =  milli2; 
 }
else                                                                // No current flowing, set both to zero
{
 gw.send(msg_S_MULTIMETERc2.set(0));
 gw.send(msg_S_MULTIMETERc12.set(0));
 lastmilli2 =  milli2;
}
}


// ------------------ Start voltage 3 readings --------------------
 

 sample_count = 0;
 sum = 0;
 while (sample_count < NUM_SAMPLES) {                                   // take a number of voltage samples  
  sum += analogRead(voltagePin3);
  sample_count++;
  delay(10);
 }
//Serial.print("sum count..."); Serial.println((sum / NUM_SAMPLES));      // print the count result. will be between 0 and 1023
int voltage3I = map(sum/NUM_SAMPLES,0,1023,0,voltSense3Max);              // map the reading and get our result in millivolts
//Serial.print("mapped volts..."); Serial.println(voltageI / 1000.0, 1);  // convert millivolts back to volts and print. the 1 at the end determines how many decimal places to show


if ( voltage3I != lastVoltage3) {                                         // check if we have a new value. only send data if it is different
 gw.send(msg_S_MULTIMETERv3.set(voltage3I / 1000.0, 1));                  // voltagel is in millivolts so we divide by 1000 to convert back to volts and
                                                                        // send voltage message to gateway with 1 decimal place
 lastVoltage3 = voltage3I;                                                // copy the current voltage reading for testing on the next loop 
}

//--------------------Start Current 3 readings---------------------------------

int milli3 = readCurrent(ACSPin3);                                       // take a reading from the ACS712 and send to the readcurrent function

//Serial.print("Milliamps..."); Serial.println(milli);                   // print the value (in milliamps) returned

if ( milli3 != lastmilli3)                                               // check if value has changed
{
 if ( milli3 > 0)                                                       // Battery is charging
 {
  gw.send(msg_S_MULTIMETERc3.set(milli3/1000.0, 1));                     // Send new data to charging amp device
  gw.send(msg_S_MULTIMETERc13.set(0));                                  // set the dis-charging amp device to zero
  lastmilli3 =  milli3;
 }
 else if (milli3 < 0)                                                  // Battery is discharging
 {
  gw.send(msg_S_MULTIMETERc3.set(0));                                  // set the charging amp device to zero
  gw.send(msg_S_MULTIMETERc13.set(abs(milli3)/1000.0, 1));             //  use abs(milli) to Send a positive number  to dis-charging amp device
  lastmilli3 =  milli3; 
 }
else                                                                // No current flowing, set both to zero
{
 gw.send(msg_S_MULTIMETERc3.set(0));
 gw.send(msg_S_MULTIMETERc13.set(0));
 lastmilli3 =  milli3;
}
}
gw.sleep(SLEEP_TIME);
}

 

/*-------------- Function to get the offset required for ACS712 to show zero with no current flowing -----------------*/
int determineVQ(int PIN)                  
 {
  digitalWrite(ledPin, HIGH);                                      // Turn on LED to indicate offset being calculated
  delay(500);                                                      // Delay to hold LED on
  digitalWrite(ledPin, LOW);                                       // Turn off LED
  delay(150);                                                      // Delay to let readings stabilise
//  Serial.print("estimating avg. quiscent voltage:");
  long acsCount = 0;
  for (int i=0; i<5000; i++)                                       //read 5000 samples to stabilise value
   {
    acsCount += analogRead(PIN);                                   // read the count value between 0 and 1023 and add it to acsCount
    delay(1);                                           
   }
  acsCount /= 5000;                                                      // acsCount now eaquals the average of the 5000 readings taken
//  Serial.print(map(acsCount, 0, 1023, 0, 5000));Serial.println(" mV");   //Print the avg in millivolts
//  Serial.print("acsCount:");Serial.println(acsCount);                               //Print the actual count value
  
  return int(acsCount - 512);                                            // return the count difference. 512 is the count for 2.5v which is what the reading should be with no current flow                           
  
}


 /*--------------- Function to read current flowing ------------------*/
 
int readCurrent(int PIN) 
{
 int count = 0;
 for (int i=0; i<5; i++)                                        //read 5 analog count samples to stabilise value
  {
   count += analogRead(PIN) - VQ;                               //subtract the offset count VQ to improve accuracy
   delay(1);
 //  Serial.print("raw count..."); Serial.println(count);
  }
 /* Notes on the conversion below
  *  .00488 is the volt value per count of the arduino adc. The analog pin measures from 0 to 5 volt and then assigns the result to 
  *  a count from 0 to 1023, thats 1024 counts including zero. If we devide 5v by 1024 we get .oo488 volts for each count.  
  *  
  *  The (count/5) just gets us the average of our 5 count samples.
  *  
  *  So after the first part of the equation  (.00488 * (count/5) is complete we have converted our count reading into volts. 
  *  
  *  The ACS712 can measure current flow in both directions so it outputs a voltage of  2.5v as it's center point (when no current is flowing).
  *  To allow for this offset we must subtract the 2.5v to center our voltage reading.
  *  
  * Thats what the next part does (.00488 * (count/5)) - 2.5) After this is complete we are left with either a negative or  positive voltage
  * reading or a reading of zero for no current flow.
  * 
  * NOTE: While the ACS712 is a 5v device it does not use the full 0 to 5v for it's output. The datasheet shows the 20A version has a sensitivity of
  *  100mv per amp, so if we multiply 100mv by 20 we get 2v.  That means the 20A ACS712 has an output range from .5v to 4.5v.  
  * 
  * So to convert our reading in volts to a reading in amps we need to add the last part ((.00488 * (count/5)) - 2.5)/(sensitivity/1000).
  * The variable sensitivity is defined at the begining of the sketch and holds the ACS712 sensitvity amount, it is stored in millivolts. 
  * That is 66mv for the 30amp,  100mv for the 20amp and 185mv for the 5amp. As sensitivity is in millivolts we need to devide it by 1000 
  * to convert it back to volts so we can use it in the equation. 
  * 
  * Now we have our Amps value stored in the float amps. Integers are much easier to work with when checking for zero so we multiply by 1000 
  * to convert it to milliamps and return it as an integer.
*/

//Serial.print("VQ = ..."); Serial.println(VQ);
//Serial.print("current count..."); Serial.println(count/5);
//Serial.print("map  milliamps..."); Serial.println(map((count/5), 102, 922, -20000, 20000));
 float amps = ((.00488 * (count/5)) - 2.5) / (sensitivity/1000);
// Serial.print("float amps..."); Serial.println(amps, 1);
  return int (amps * 1000);                                         // convert to milliamps and return as an integer

}
Insert Code Here

English:

Hello

My English is not that good.
I tried to build the project. The button I need (I think) not, but I have extended the script, however, by 2 more current and voltage sensors. The goal is to get 3 times Current and 3 times Volt as a result. I have 30A sensors and a 30A charger. In between are 30A fuses.
Unfortunately in Domoticz but only one time Volt and 2 times Current. Unfortunately I have not really much idea of ​​the programming. Could someone here over the sketch look around to see if I have a mistake in it?do i

[gohan]

@aDm1N
Do you have a log of the data being sent from the node? What mysensors library version are you using?

[mrc-core]

Hi. i have been working on this solar code and have made the changes to work over mysensors 2.1.1
I'm now triyng to add a line code to monitor the voltage from the solar panels. Can anyone give me a help on this?
I want to now the voltage watts or kws produce over my pannels. The idea is to have domoticz monitoring all data produce over the solar pannel.
Thanks

/*Sketch for a MySensor node to monitor a 12v battery with a solar panel for charging
 * The node monitors battery voltage,current into and out of the battery, ambient temperature and battery temperature.
 * 2 x DS18b20 dallas temperature ic's their data pins connected to arduino digital pin 3
 * 1 x ACS712 current sensor module connected to  arduino analog pin A4
 * 1 x 25v voltage sensor module connected to arduino analog pin A0
 * 1 x nRF24L01+  2.4ghz tranceiver connected as per the MySensors web site.
 * 1 x LED connected via a 330 ohm resistor to pin 6
 * 1 x push button connected to pin 5
 */

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE
 
#include <MySensors.h>  
#include <SPI.h>
#include <OneWire.h>
#include <DallasTemperature.h>
 
#define ONE_WIRE_BUS 3                            // Ds18b20 data wire is connected to digital pin 3 on the Arduino
#define ID_S_TEMP_A 0                             // First temp device
#define ID_S_TEMP_B 1                             // Second temp device
#define ID_S_MULTIMETERV 3                        // Multimeter device for voltage measurement
#define ID_S_MULTIMETERC 4                        // Multimeter device for positive current measurement 
#define ID_S_MULTIMETERC1 5                       // Multimeter device for negative current measurement
#define NUM_SAMPLES 10                            // number of analog voltage samples to take per reading

int ledPin = 6;                                   // the pin for the LED
int buttonPin = 5;                                // the input pin for offset pushbutton
int buttonState = 0;                              // variable for reading the pin status
unsigned long SLEEP_TIME = 30000;                 // Sleep time between reads (in milliseconds)
int lastmilli = 25000;                            // set to an arbitary number outside of expected current sensor range to ensure a change when first run 
float sensitivity = 66 ;                          // change this to 185 for ACS712-5 or to 100 for ACS712-20A or to 66 for ACS712-30A
int VQ = 0;                                       // Placeholder for quiescent voltage calculations
int ACSPin = A4;                                  // Analog pin number the ACS712 data pin connects to
float lastTemperature[2];                         // Array to hold the last temp readings sent to gateway, only send new data if different
int sum = 0;                                      // sum of voltage samples taken
unsigned char sample_count = 0;                   // current sample number
int lastVoltage = 30000;                          // set to an arbitary number outside of expected voltage sensor range to ensure a change when first run
int voltagePin = A0;                              // analog pin voltage sensor or voltage divider is connected to
int voltSenseMax = 25000;                         // set to the maximum input voltage in millivolts of your voltage divider input    
OneWire oneWire(ONE_WIRE_BUS);                    // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire);              // Pass our oneWire reference to Dallas Temperature.

// ------ Initialize  messages ------- //
MyMessage msg(0,V_TEMP);                     
MyMessage msg_S_MULTIMETERv(ID_S_MULTIMETERV,V_VOLTAGE);
MyMessage msg_S_MULTIMETERc(ID_S_MULTIMETERC,V_CURRENT);
MyMessage msg_S_MULTIMETERc1(ID_S_MULTIMETERC1,V_CURRENT); 

void presentation()  
{
  // Send the sketch version information to the gateway
  sendSketchInfo("Battery Status Sensor", "2.1.1");

  // Register all sensors to gw (they will be created as child devices)
  present(ID_S_TEMP_A, S_TEMP);
  present(ID_S_TEMP_B, S_TEMP);
  present(ID_S_MULTIMETERV,V_VOLTAGE);
  present(ID_S_MULTIMETERC,V_CURRENT);
  present(ID_S_MULTIMETERC1,V_CURRENT);
}

void setup()
{
  sensors.begin();                                      // Start up the onewire library
  pinMode(buttonPin, INPUT_PULLUP);                     // Set buttonPin as input and turn on internal pull up resistor
  pinMode(ledPin, OUTPUT);                              // Set ledPin as output
  digitalWrite(ledPin, LOW);                            // Make sure ledPin is off

  // ------ load offset for current sensor
  int validCheck = loadState(0);
  if (validCheck == 120)                                // check to see if valid data exists
  {
    VQ = loadState(1);                                  // Load count offset into VQ
    //Serial.print(" positive VQ offset loaded..."); Serial.println(VQ);
  }
  else if (validCheck == 125) 
  {
    VQ = -abs(loadState(1));
    //Serial.print(" negative VQ offset loaded..."); Serial.println(VQ);
  }
  else 
  {
    //Serial.println("VQ offset not set");
  }
  delay(500);  
}
 
void loop()
{
  buttonState = digitalRead(buttonPin);
  //Serial.print("buttonstate..."); Serial.println(buttonState);
  if (buttonState == LOW) 
  {
    VQ = determineVQ(ACSPin);                           // Returns the offset count needed to show zero with no load
    if (VQ >= 0 && VQ < 255) 
    {                                                   // check for valid data. VQ is positive number
      saveState(0, 120);                                // Store 120 value  in eeprom position 0. use this to check for valid data at boot
      saveState(1, VQ);                                 // Store offset count in eeprom. in case of re-boot  
    }
    else if (VQ < 0 && VQ > -255)                       // VQ is a negative number. negatives cannot be stored in eeprom 
    {                                                   
      saveState(0, 125);                                // Store 125 value  in eeprom position 0. use this to check for valid data at boot
      saveState(1, abs(VQ));                            // convert VQ to positive and  Store offset count in eeprom. in case of re-boot   
    }
  }
  
//-------------------------------------------- Start voltage readings ----------------------------------------------------
  
  sample_count = 0;
  sum = 0;
  while (sample_count < NUM_SAMPLES)                     // take a number of voltage samples 
  {                     
    sum += analogRead(voltagePin);
    sample_count++;
    delay(10);
  }
 
  //Serial.print("sum count..."); Serial.println((sum / NUM_SAMPLES));        // print the count result. will be between 0 and 1023
  int voltageI = map(sum/NUM_SAMPLES,0,1023,0,voltSenseMax);                  // map the reading and get our result in millivolts
  //Serial.print("mapped volts..."); Serial.println(voltageI / 1000.0, 1);    // convert millivolts back to volts and print. the 1 at the end determines how many decimal places to show

  if ( voltageI != lastVoltage)                                               // check if we have a new value. only send data if it is different
  {
    send(msg_S_MULTIMETERv.set(voltageI / 1000.0, 1));                        // voltagel is in millivolts so we divide by 1000 to convert back to volts and send voltage message to gateway with 1 decimal place
    lastVoltage = voltageI;                                                   // copy the current voltage reading for testing on the next loop 
  }

//---------------------------------------- Start Current readings ---------------------------------------------------------
  
  int milli = readCurrent(ACSPin);                                            // take a reading from the ACS712 and send to the readcurrent function
  //Serial.print("Milliamps..."); Serial.println(milli);                      // print the value (in milliamps) returned
  if ( milli != lastmilli)                                                    // check if value has changed
  {
    if ( milli > 0)                                                           // Battery is charging
    {
      send(msg_S_MULTIMETERc.set(milli/1000.0, 1));                           // Send new data to charging amp device
      send(msg_S_MULTIMETERc1.set(0));                                        // set the dis-charging amp device to zero
      lastmilli =  milli;
    }
    else if (milli < 0)                                                       // Battery is discharging
    {
      send(msg_S_MULTIMETERc.set(0));                                         // set the charging amp device to zero
      send(msg_S_MULTIMETERc1.set(abs(milli)/1000.0, 1));                     //  use abs(milli) to Send a positive number  to dis-charging amp device
      lastmilli =  milli; 
    }
    else                                                                      // No current flowing, set both to zero
    {
      send(msg_S_MULTIMETERc.set(0));
      send(msg_S_MULTIMETERc1.set(0));
      lastmilli =  milli;
    }
  }
 
//--------------------------------------- Temperature readings start ------------------------------------------------------------

  Serial.println(" Requesting temperatures...");
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();                              // call sensors.requestTemperatures() to issue a global temperature request to all devices on the bus

  // ------- query conversion time and sleep until conversion completed ------
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  sleep(conversionTime);

  for (int i=0; i<2; i++) 
  {
    //Serial.print("Temperature for Device: ");Serial.print(i);Serial.print(" is: ");
    //Serial.println(sensors.getTempCByIndex(i)); // Why "byIndex"? 
    // You can have more than one IC on the same bus. 
    // 0 refers to the first IC on the wire

    float temperature = static_cast<float>(static_cast<int>((sensors.getTempCByIndex(i)) * 10.)) / 10.;    // Fetch and round temperature to one decimal in celcius
    if (lastTemperature[i] != temperature)                                                                 // check for a changed temperature reading
    {
      send(msg.setSensor(i).set(temperature,1));                                                           // Send in the new temperature
      lastTemperature[i]=temperature;                                                                      // Save new temperatures for next compare
    }     
  }
  sleep(SLEEP_TIME);
}

/*-------------- Function to get the offset required for ACS712 to show zero with no current flowing -----------------*/
int determineVQ(int PIN)                  
{
  digitalWrite(ledPin, HIGH);                                             // Turn on LED to indicate offset being calculated
  delay(500);                                                             // Delay to hold LED on
  digitalWrite(ledPin, LOW);                                              // Turn off LED
  delay(150);                                                             // Delay to let readings stabilise
  //Serial.print("estimating avg. quiscent voltage:");
  long acsCount = 0;
  for (int i=0; i<5000; i++)                                              // read 5000 samples to stabilise value
  {
    acsCount += analogRead(PIN);                                          // read the count value between 0 and 1023 and add it to acsCount
    delay(1);                                           
  }
  acsCount /= 5000;                                                       // acsCount now eaquals the average of the 5000 readings taken
  //Serial.print(map(acsCount, 0, 1023, 0, 5000));Serial.println(" mV");  // Print the avg in millivolts
  //Serial.print("acsCount:");Serial.println(acsCount);                   // Print the actual count value
  return int(acsCount - 512);                                             // return the count difference. 512 is the count for 2.5v which is what the reading should be with no current flow                           
  
}

/*--------------- Function to read current flowing ------------------*/
int readCurrent(int PIN) 
{
 int count = 0;
 for (int i=0; i<5; i++)                                                  // read 5 analog count samples to stabilise value
  {
   count += analogRead(PIN) - VQ;                                         // subtract the offset count VQ to improve accuracy
   delay(1);
  //Serial.print("raw count..."); Serial.println(count);
  }
 
/* Notes on the conversion below
 *  .00488 is the volt value per count of the arduino adc. The analog pin measures from 0 to 5 volt and then assigns the result to 
 *  a count from 0 to 1023, thats 1024 counts including zero. If we devide 5v by 1024 we get .oo488 volts for each count.  
 *  
 *  The (count/5) just gets us the average of our 5 count samples.
 *  
 *  So after the first part of the equation  (.00488 * (count/5) is complete we have converted our count reading into volts. 
 *  
 *  The ACS712 can measure current flow in both directions so it outputs a voltage of  2.5v as it's center point (when no current is flowing).
 *  To allow for this offset we must subtract the 2.5v to center our voltage reading.
 *  
 * Thats what the next part does (.00488 * (count/5)) - 2.5) After this is complete we are left with either a negative or  positive voltage
 * reading or a reading of zero for no current flow.
 * 
 * NOTE: While the ACS712 is a 5v device it does not use the full 0 to 5v for it's output. The datasheet shows the 20A version has a sensitivity of
 *  100mv per amp, so if we multiply 100mv by 20 we get 2v.  That means the 20A ACS712 has an output range from .5v to 4.5v.  
 * 
 * So to convert our reading in volts to a reading in amps we need to add the last part ((.00488 * (count/5)) - 2.5)/(sensitivity/1000).
 * The variable sensitivity is defined at the begining of the sketch and holds the ACS712 sensitvity amount, it is stored in millivolts. 
 * That is 66mv for the 30amp,  100mv for the 20amp and 185mv for the 5amp. As sensitivity is in millivolts we need to devide it by 1000 
 * to convert it back to volts so we can use it in the equation. 
 * 
 * Now we have our Amps value stored in the float amps. Integers are much easier to work with when checking for zero so we multiply by 1000 
 * to convert it to milliamps and return it as an integer.
*/

//Serial.print("VQ = ..."); Serial.println(VQ);
//Serial.print("current count..."); Serial.println(count/5);
//Serial.print("map  milliamps..."); Serial.println(map((count/5), 102, 922, -20000, 20000));
  float amps = ((.00488 * (count/5)) - 2.5) / (sensitivity/1000);
//Serial.print("float amps..."); Serial.println(amps, 1);
  return int (amps * 1000);                                         // convert to milliamps and return as an integer
}```

[mrc-core]

I'm working again on this system but i'm having some troubles... The code has you caan see i have already adapted it to version 2.1.1 Now on the hardware i'm building i have this:

• 1 solar panel 10w connected to the LM2596 that converts the 12v to 5.5v that goes to the LiPo Enhanced Charger Module, here i have the 3,7v bat connected and the arduinos connected to the other power out.

My problem is that when i have the system online the values i'm getting are not right. For the battery voltage i get 5,5v when i believe i should be getting 3,7v or 4,1v maximum.
The charge and load are always on 0,2A or 0,0A

I have the acs712 connected to the negative side off the battery and the Voltage sensor connected to the negative and positive side off the battery.

What i'm i doing rong here ????

[Boots33]

@mrc-core From your code it looks like you are using a 30A acs712 and you are still using the 25v sensor to measure the expected 4v. With only a 10w panel you might be better off with a 5A acs712 and also a voltage divider that maxes out at around 10v. This will give you a better resolution to work with right from the start.

How are you powering the arduino? Perhaps you can do a drawing of how your project is wired together. Remember the arduino needs to have a stable 5v supply to have any chance of giving a good result.

[mrc-core]

Hi. sorry for my late replay....
Here's the way i'm powering things up.
I don't have a solar charge since last summer we had a big fire on my island and all my arduino and sensors that were outside were all damage from the fire and hot temperatures. So to fiz this problem i'm using the LM2596 to reduce the 12V from the solar panels to 5.5V so that the lipo charger can work. Above the 5v this charger will get damage.

Some data from this charger:
LED: Red = Charging, Green = Complete
Input Voltage: 4.5 to 5.5V
Battery Max Charge Voltage: 4.2V - charges a 1S Lithium Ion Polymer Battery

This outputs a 4.2V on the load and batt connections.

My arduino and sensors are connected to the load pins from the lipo charger as you can see on the picture.
Thanks for your replay and help.

[Boots33]

@mrc-core The original circuit/sketch was designed for a 5v arduino and was measuring a 12v system . From your drawing it looks like you will be using a 3v arduino so at the very least you will need to change the voltage divider to give you a better resolution. As to the acs712 it is a 5v device so most likely will not even work on 3v so you may need to source some other device for current measurement. Again you would want a low current device if you are to have any chance of measuring the few milliamps you would be seeing. perhaps a google search for acs712 on 3v will produce a result.

[mrc-core]

@Boots33 I'm going to change the arduino mini for an arduino nano to have the 5V still have one in the house.
Acs712 have already buy 2 off them just in case if i have to go back to arduino mini.

I was thinking on booting all my outside arduinos from this solar panel i have 2 more off them that i can connect.

[mrc-core]

@Boots33 I have change to an arduino nano but still get some strange values. I'm going to make some changes over this project and see again what ill get.

Thanks for all the help.

[Boots33]

@mrc-core Ok, let me know how you get on.
I think solar powering the nodes is a great idea, I have several nodes and three raspberry pi's running on my house solar system at the moment.

[unfadingpyro]

I just finished setting up this sensor to monitor my solar panels. The voltage sensors is reporting correct, but i'm not sure if the current sensor is right or wired correctly.

This is how it is currently wired.

Is this going to give me both charge and discharge?

Thanks!

[Boots33]

@unfadingpyro I can't see your wiring diagram.

[mfalkvidd]

Me neither. This is what it looks like to me:

[unfadingpyro]

How about now?