Choosing the right controller, how

blebbens

Looks nice...

Connected a serial gateway via USB to an raspberry pi 3 running domoticz and configured it as described. Uploaded the serialgateway.ino-Sketch to the arduino nano. I installed a decoupling capacitor.

Afterwards I have build a mysensors motion sensor (HC-SR501, NRF24L01, Arduino nano) and uploaded an arduino-mysensors-sketch.

But, domoticz->hardware does not show any node/child.
Wanted to see success - did I understand anything wrong ?

Tore André Rosander

@blebbens Can you see it in setup -> devices?

When you connect your node, does the log show anything?

blebbens

Mysensors: Gateway ready (version 1.5.4). This shows me the log.
Can´t the the node.

I uploaded sketches, but did not changed them. The arduino nano connected to the motion sensor is powered by a small power bank. The leds on the nano are off until I press the power bank button.

blebbens

Is there a way to test the gateways function ?
domoticz is showing the hardware, but does this mean, all is set up and connected correctly ?

Tore André Rosander

@blebbens This should mean that the gateway is responding "Mysensors: Gateway ready (version 1.5.4)."

What does the serial monitor say if you start the node when connected to the computer?

In domoticz -> setup -> settings, is "allow new hardware" activated?

blebbens

I am at work for the next 12 hours... I think you are right, think it is not activated.
Isn´t there a button for allowing new hardware for the next 5 minutes ?

Okay, trying it in the evening, thanks.

One more question please: (perhaps I should ask in domoticz forum)
Domoticz is running on my RPi3. I would like to add a raspberry 7" touch screen and install it on the wall. The screen should show a dashboard, But, at the moment I let the RPi boot into console for saving resources.
Is there a way to show a dashboard without starting the whole KDE GUI ? The screen should deactivate after 5 minutes without action - and activate on finger tip.

blebbens

Activated allowing new hardware.
Mysensor serial gateway 2.0 finds an unknown node version 1.0 with one child. Child is named s_arduino_repeater_node 2.0.
The log shows this: : MySensors: Update command received for unknown node_id: -1, child_id: 255

Could someone help?

Just uploaded an unmodified sketch from mysensors to a combination of motion sensor, NRF24L01 and arduino nano.

Tore André Rosander

I know this one works on my nano:

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik Ekblad
 * 
 * DESCRIPTION
 * Motion Sensor example using HC-SR501 
 * http://www.mysensors.org/build/motion
 *
 */

// Enable debug prints
// #define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#include <SPI.h>
#include <MySensor.h>

unsigned long SLEEP_TIME = 120000; // Sleep time between reports (in milliseconds)
#define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define INTERRUPT DIGITAL_INPUT_SENSOR-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define CHILD_ID 1   // Id of the sensor child

// Initialize motion message
MyMessage msg(CHILD_ID, V_TRIPPED);

void setup()  
{  
  pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Motion Sensor", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_MOTION);
}

void loop()     
{     
  // Read digital motion value
  boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
        
  Serial.println(tripped);
  send(msg.set(tripped?"1":"0"));  // Send tripped value to gw 
 
  // Sleep until interrupt comes in on motion sensor. Send update every two minute. 
  sleep(INTERRUPT,CHANGE, SLEEP_TIME);
}

Adam Novak

hi,
i haven't find anywhere yet, but is it possible to use mysensors mqtt gateway with domoticz?

blebbens

At the moment I have running a Raspberry Pi 3 with domoticz and a VeraEdge UI7.

After a long time my ethernet gateway (arduino nano) seems to be running... To verify the connection between the gateway and a node I wanted to build a air quality sensor using a MQ-135 sensor.

I noticed that Vera needs special .xml and .json-files for this. Otherwise Vera does not recognize the sensor/node.

It took several weeks to walk around many errors (mysensor was not compiling using IDE > 1.6.9, 1.6.8 works, in 1.6.10 you have to delete avr-gcc to get this working).

I would like to ask:
Does domoticz need special files/settings for each sensor ?
Does Vera really need special files for recognizing mysensors sensors ?

hek

@blebbens said:

Does Vera really need special files for recognizing mysensors sensors ?

Vera (by default) does not support all the sensor types available in MySensors. But i has the standard stuff, like switch, temp, humidiy etc.

If you want to use a none-standard device, like the distance sensor, you have to install a couple of device files (provided in the Vera github repo) which describes how it should presented GUI wise.

blebbens

Ok, thanks.

And, how does domoticz handle this? Does it need special files, too?

hek

@blebbens said:

Does it need special files, too?

No, I don't think so.

blebbens

I really do not know which one to choose: VeraEdge or Domoticz...
But, I am running several Homematic (eq-3) devices. It would be so great to access this devices via the controller. None of them supports Homematic.

Homee supports homematic, but homee does not support mysensors.

hek

Haven't heard of homee before. Is it popular in germany?

blebbens

It is very popular. Was on kickstarter I think.
Homematic is very famous/big in germany. A controller, which can handle homematic and mysensors would be the best solution.

Choosing the right controller, how

18

11.7k

11.2k

113.0k