💬 The Sensor Network

[frydrik]

@skywatch Hello, I am from the Republic of Moldova, I am a Romanian speaker, I also learned the Russian language, My country is the poorest country in Europe. I am also trying to implement this remote meter reading project as a pilot project, on my own account, I have no funding here, I have to implement it myself without any resources. so I can't say this is a commercial project

[skywatch]

@frydrik OK, so with no funding the only option is to educate yourself little-by-little.

Build a small test system and keep trying it in new locations to see how it goes. Learning by doing is the best and quickest way I think.

Have you considered that signals might be hacked, spoofed or jammed? How will you mitigate such things?

What you want to do may seem simple at first, but there is a lot to think about with such big ambitions.

There is no easy short cut - try things for yourself and if you have problems then post them here and I am sure many people will try and help you.

[frydrik]

@skywatch Hi, thank you very much for the encouragement, I will try to document the steps I did with pictures with schemes, but I will also think about security.

[skywatch]

@frydrik My approach would be to make one gateway and one node only. It will simplify testing and speed it up a lot!

Decide which bootloader you will use and why (the below list will impact that decision).

Learn how to burn a bootloader and when successful move on to....

Get the code working.

Then add soft or hard signing to messages if you think you need to.
Then add encryption to messages if you think you need to.
Then add wireless firmware updates (FOTA) if you think you need to.

Then, when you have it all as you want it is easy to duplicate it very quickly to lots of nodes. And test again.

Also I suggest manually assigning node ID's as when power goes off they will all come back with the same ID, not randomly assigned ones.

Always save a modified sketch with a new name or verison so if things don't go well you can go back to the last working version.

It is very likely that you will hit many obsticals along the way. You need to remain focused and determined to do what you want. Be warned that it's going to take some time.

[frydrik]

@skywatch
Hi, now I do, I have 1 gate and 3 nodes, I have already connected 1 node to a test meter, now I choose the same data that is displayed on the meter screen and MYCONTROLLER, node ID I install it manually, now I want to test at what maximum distance can the connection between the gate and the node be made, the gate is made on TTGO LoRa32 SX1276 OLED and the test node also TTGO LoRa32 SX1276 OLED, the other 2 nodes are nodemcu esp8266 + RFM95, they have standard antennas that do not inspire me much confidence , I want to try to build other antennas to see the difference between the standard antenna and the one I made, then I want to solve the problem with bootloader for FOTA, I think to create the nodes from nodemcu esp8266 + RFM95 because I want to connect to a node several counters from 2-6-8, because arduino Pro Mini / Nano no more than 2 interrupts esp8266 all gpio can be as interrupt, here I think how to do bootloader for FOTA.!!
my test stand:

[RagoTube]

Hi friends, in the above "The Radio Communication" topic I see these lines "You can also send messages directly between two nodes in the network without transiting through the gateway. For example, your outside temperature sensor can send its data directly to another sensor in your kitchen with an attached display."
This is what I am struggling to achieve , please help me with an Example Sketch for both sender and receiver for the above setup and it will be a great start for me to explore the excellent features of MySensors IoT.

[jkandasa]

@RagoTube examples are there in,

• https://github.com/mysensors/MySensors/tree/development/examples
• https://github.com/mysensors/MySensorsArduinoExamples

The following sketch can help you to get your setup,
https://github.com/mysensors/MySensors/blob/development/examples/Node2Node/Node2Node.ino

[RagoTube]

@jkandasa Hi, thank you, I am a newbie, please advice what are the changes to be done to use Node2Node, to receive data from a sender and display on a LCD or OLED please. I am finding difficult only on the Receiver side, please help.
With Great Regards,

[jkandasa]

@RagoTube
Note: I didn't test this code. I believe it should work.

Sender node

#define MY_DEBUG
#define MY_RADIO_RF24
#define MY_NODE_ID 21

#define DISPLAY_NODE_ID 0

#define TEMPERATURE_SENSOR_ID 0

#include "MySensors.h"

// triggering interval
static const uint32_t trigger_ms = 10000; // 10 seconds

uint32_t lastTrigger = 0;
MyMessage msgGeneral(TEMPERATURE_SENSOR_ID, V_TEMP);

void setup() {
}

void presentation() {
  sendSketchInfo("Temperature node 1", "1.0");
  present(TEMPERATURE_SENSOR_ID, S_TEMP, "Temperature");
}

void loop() {
  if (millis() - lastTrigger > trigger_ms) {
    lastTrigger = millis();
    // set destination address
    msgGeneral.setDestination(DISPLAY_NODE_ID);
    
    // get temperature from your temperature sensor
    float lastTemperature = 0.0; // update from your sensor

    // send message to display node
    send(msgGeneral.set(lastTemperature));
  }
}

Display node (Gateway node)

#define MY_DEBUG
#define MY_RADIO_RF24
#define MY_GATEWAY_SERIAL

#define TEMPERATURE_SENSOR_ID 0
#define TEMPERATURE_NODE_ID 21

#include "MySensors.h"

float lastTemperature = 0.0;

void presentation() {
  sendSketchInfo("Display node / Gateway", "1.0");
}

void setup() {
}

void loop() {
}

void updateDisplay() {
  // update your display with "lastTemperature"
}

void receive(const MyMessage &message) {
  if (message.sender == TEMPERATURE_NODE_ID) { // message from temperature node
    if (message.sensor == TEMPERATURE_SENSOR_ID && message.type == V_TEMP) { // message from temperature sensor
      lastTemperature = message.getFloat();
      updateDisplay(); // update display
    }
  }
}

[RagoTube]

Thank you so much and very kind of you. I will try this.

[RagoTube]

Hai jkandasa, It works fine, thank you so much for your examples and it cleared lot my doubts. Thanks again, you have given me good start.

[RagoTube]

Hi, I missed to notice that, it works as long as the Gateway is ON, when I turn off the Gateway it stops receiving the data. I assumed that your example "Node2Node" code will work with out a Gateway in between. Please advice.

[jkandasa]

@RagoTube looks like we need a gateway in a sensor network and with the help of gateway node-node communication can happen. The beauty of MySensors gateway is, you can use your gateway as a node.
I just updated my example shown here. Now the display node is a gateway node.

[RagoTube]

Thanks again for your immediate advice. It should be OK now.