Stay on version 1.5 or move to 2.1.1 on my vera plus and vera 3?

[Corvl]

Hello everyone,

I run version 1.5 on both my vera's and Ethernet gateways and someone hinted to go to version 2.x since the newer codes don't work with 1.5

I also read on this forum there are issues with version 2.x and library.
Is it usefull to stay on version 1.5 or I better upgrade?

I run not that many nodes , an important one, servo actuator which is working good. And a door sensor with temperature sensor which is working not so good , it doesn't report alway , so an extra piece of code is inserted so it reports at least every 30 seconds. Maybe with the new library and codes this is solved , and it reports a change immediately?

This is the code for the servo actuator I use , will it still work with version 2.11?

// Example showing how to create an atuator for a servo.
// Connect red to +5V, Black or brown to GND and the last cable to Digital pin 3.
// The servo consumes much power and should probably have its own powersource.'
// The arduino might spontanally restart if too much power is used (happend
// to me when servo tried to pass the extreme positions = full load).
// Contribution by: Derek Macias


#include <MySensor.h>
#include <SPI.h>
#include <Servo.h> 

#define SERVO_DIGITAL_OUT_PIN 3
#define SERVO_MIN 0 // Fine tune your servos min. 0-180
#define SERVO_MAX 180 // Fine tune your servos max. 0-180
#define DETACH_DELAY 4000 // Tune this to let your movement finish before detaching the servo
#define CHILD_ID 10   // Id of the sensor child

MySensor gw;
MyMessage msg(CHILD_ID, V_DIMMER);
Servo myservo;  // create servo object to control a servo 
                // a maximum of eight servo objects can be created Sensor gw(9,10);
unsigned long timeOfLastChange = 0;
bool attachedServo = false;
            
void setup() 
{ 
  // Attach method for incoming messages
  gw.begin(incomingMessage);

  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo("Servo", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID, S_COVER);

  // Request last servo state at startup
  gw.request(CHILD_ID, V_DIMMER);
} 

void loop() 
{ 
  gw.process();
  if (attachedServo && millis() - timeOfLastChange > DETACH_DELAY) {
     myservo.detach();
     attachedServo = false;
  }
} 

void incomingMessage(const MyMessage &message) {
  myservo.attach(SERVO_DIGITAL_OUT_PIN);   
  attachedServo = true;
  if (message.type==V_DIMMER) { // This could be M_ACK_VARIABLE or M_SET_VARIABLE
     int val = message.getInt();
    val = map(val, 0, 100, 0, 180); // scale 0%-100% between 0 and 180)
        myservo.write(val);       // sets the servo position 0-180
     // Write some debug info
     Serial.print("Servo changed. new state: ");
     Serial.println(val);
   } else if (message.type==V_UP) {
     Serial.println("Servo UP command");
     myservo.write(SERVO_MIN);
     gw.send(msg.set(100));
   } else if (message.type==V_DOWN) {
     Serial.println("Servo DOWN command");
     myservo.write(SERVO_MAX); 
     gw.send(msg.set(0));
   } else if (message.type==V_STOP) {
     Serial.println("Servo STOP command");
     myservo.detach();
     attachedServo = false;

   }
   timeOfLastChange = millis();
}```

[marceltrapman]

@Corvl Hi, I did not have many sensors until now but I am ready to add stuff ( I finally have some time again :) ).
Because of that I decided to re-evaluate my sensors and to upgrade in the process.

You probably guessed it but this is what I would do.

If you are not planning to add (many) sensors and everything works well I would stay with 1.5.

If either or both of the above conditions == false I would move to 2.2.1 (current version).

[Corvl]

I would like to add some more stuff as well, and hopefully , with the newer version that doorsensor is working better.

But is 2.11 working on vera?
And the above sketch , of the servo actuator , is that one still compatible?

Thanks,
Cor

[marceltrapman]

@Corvl I can't comment on the vera question.

For 2.1.1 you have to make some changes but they are not too difficult ;)

[Boots33]

@Corvl I am also not sure of any problems with Vera.

Had a quick look at your sketch and it should be ok in version 2.

V_DIMMER has been Deprecated and although it will still work at the moment you should now use V_PERCENTAGE instead

Did a quick re-write for V2 so you can see what is different. I think I got all the changes
I think you will find v2 easier to use once you get the hang of it

// Example showing how to create an atuator for a servo.
// Connect red to +5V, Black or brown to GND and the last cable to Digital pin 3.
// The servo consumes much power and should probably have its own powersource.'
// The arduino might spontanally restart if too much power is used (happend
// to me when servo tried to pass the extreme positions = full load).
// Contribution by: Derek Macias

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
//#define MY_REPEATER_FEATURE

#include <MySensors.h>
//#include <MySensor.h>
#include <SPI.h>
#include <Servo.h> 

#define SERVO_DIGITAL_OUT_PIN 3
#define SERVO_MIN 0 // Fine tune your servos min. 0-180
#define SERVO_MAX 180 // Fine tune your servos max. 0-180
#define DETACH_DELAY 4000 // Tune this to let your movement finish before detaching the servo
#define CHILD_ID 10   // Id of the sensor child

//MySensor gw;   
//MyMessage msg(CHILD_ID, V_DIMMER);  //V_DIMMER has been deprecated use V_PERCENTAGE instead
MyMessage msg(CHILD_ID, V_PERCENTAGE);
Servo myservo;  // create servo object to control a servo 
                // a maximum of eight servo objects can be created Sensor gw(9,10);
unsigned long timeOfLastChange = 0;
bool attachedServo = false;
            
void setup() 
{ 
  // Attach method for incoming messages
 // gw.begin(incomingMessage);

  // Send the sketch version information to the gateway and Controller
  //gw.sendSketchInfo("Servo", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  //gw.present(CHILD_ID, S_COVER);

  // Request last servo state at startup
  //gw.request(CHILD_ID, V_DIMMER);
  request(CHILD_ID, V_PERCENTAGE);
} 

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Servo", "1.0");

  // Register all sensors to gateway (they will be created as child devices)
  present(CHILD_ID, S_COVER);
}


void loop() 
{ 
 // gw.process();
  if (attachedServo && millis() - timeOfLastChange > DETACH_DELAY) {
     myservo.detach();
     attachedServo = false;
  }
} 

//void incomingMessage(const MyMessage &message) {
void receive(const MyMessage &message){
  
  myservo.attach(SERVO_DIGITAL_OUT_PIN);   
  attachedServo = true;
  //if (message.type==V_DIMMER) { // This could be M_ACK_VARIABLE or M_SET_VARIABLE
  if (message.type==V_PERCENTAGE) {
     int val = message.getInt();
    val = map(val, 0, 100, 0, 180); // scale 0%-100% between 0 and 180)
        myservo.write(val);       // sets the servo position 0-180
     // Write some debug info
     Serial.print("Servo changed. new state: ");
     Serial.println(val);
   } else if (message.type==V_UP) {
     Serial.println("Servo UP command");
     myservo.write(SERVO_MIN);
    // gw.send(msg.set(100));
       send(msg.set(100));
   } else if (message.type==V_DOWN) {
     Serial.println("Servo DOWN command");
     myservo.write(SERVO_MAX); 
  //   gw.send(msg.set(0));
       send(msg.set(0));  
   } else if (message.type==V_STOP) {
     Serial.println("Servo STOP command");
     myservo.detach();
     attachedServo = false;

   }
   timeOfLastChange = millis();
}

[Corvl]

Thanks a lot , that is a big re-assurance , since that servo is hooked up on my heating system...... and it is still winter.

Still , there are 2 or 3 threads here on this forum saying they cab's get version 2.x to work with vera on Ui7.

I have a spare vera lite on Ui7 I will try this version 2.x on the vera lite first. But it will be for next week.

Thanks a lot so far!,
Cor