Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

New Sensor Domoticz

arduino_89_89 last edited by

Hi everyone, I have two sensors I can not configure them in Domoticz.
Mq2 gpl and rain sensor Mhrd. How can I do?
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by @arduino_89_89

@arduino_89_89 welcome to the MySensors community.

What did you do and what were the results?
Reply Quote 0
1 Reply Last reply
arduino_89_89 last edited by

I followed the Mq2 Sensor Tutorial, but I'm only out of the kids and not on devices. Instead, for the rain sensor I did not find anything.
Reply Quote 0
1 Reply Last reply

3
Posts

1010
Views

Log in to reply

Suggested Topics

MYSBootloader 1.3 pre-release & MYSController 1.0.0beta
Development • ota myscontroller mysbootloader • • tekka

196

13
Votes

196
Posts

84949
Views

If anyone is getting "Property 'bootloader.tool.' is undefined" error with arduino 2.x when trying to burn bootloader, then you just have to add another row in bold below to boards.txt file MYSBL.upload.tool=avrdude MYSBL.upload.protocol=arduino MYSBL.upload.maximum_size=30720 MYSBL.upload.maximum_data_size=2048 MYSBL.bootloader.tool=avrdude MYSBL.bootloader.tool.default=avrdude
GatewayESP32MQTT with local sensor crashes
Development • • Stig

11

0
Votes

11
Posts

38
Views

@Stig I wouldn't bet on anything soon.
Help, version 2.4-alpha, PI-4 64bits & Mac OS
Development • 2.4 pi 4 64bits macos • • briseis

2

0
Votes

2
Posts

14
Views

@briseis I would just switch back to 2.3.2 I also believe 2.4 on the gateway should work with nodes on 2.3.2. what kind of errors did you get when doing this?
Compilation failure
Development • • mtedds

3

0
Votes

3
Posts

22
Views

Wow - given the age of the most recent messages on here, I wondered if I would get a response. Many thanks for responding so quickly and my problem is resolved. [ Note I now also have PlatformIO installed and that compiled the sketch at the first attempt. I can't work out which version of the board it is using, as it uses different naming conventions, but I think it is the most recent. ]
Buttler/Jenkins error I don't understand
Development • • eiten

1

0
Votes

1
Posts

9
Views

No one has replied
433 mhz from Arduino to Raspberry
Development • • martin1234567

3

0
Votes

3
Posts

18
Views

I would recommend to switch to a nrf24l01 or rfm69/95, where you will have bidirectional communication and you can use the mysensors framework
Node to node communication fails if gateway is not reachable
Development • • Heizelmann

30

0
Votes

30
Posts

5409
Views

the Node To Node must be seen as a Gateway to node the controller is not mandatory. so we rethink the topology. Gateway (node0) <---> Node1 <---> Node2 <---> 3.. 4... The Gateway in 2022/2023 must be used, how to do!!?!! ...... a Node Useful (yes an old message, but to refresh the ideas ) happy holidays to you all
PlatformIO, nRF52832 and MyBoardNRF5
Development • • Stig

10

0
Votes

10
Posts

51
Views

@electrik upload_port does not specify the target. It just selects if you'll use the gdb port or the uart port from the BMP. The target I'm talking about is what comes up when trying to do upload. Configuring upload protocol... AVAILABLE: blackmagic, cmsis-dap, jlink, nrfjprog, nrfutil, stlink CURRENT: upload_protocol = blackmagic Looking for BlackMagic port... Auto-detected: COM2 Uploading .pio\build\MyBoardNRF5\firmware.hex Target voltage: 3.45V Available Targets: No. Att Driver 1 Nordic nRF52 M3/M4 2 Nordic nRF52 Access Port 0x000020d8 in transportProcessFIFO() () Loading section .text, size 0x895c lma 0x0 Loading section .ARM.exidx, size 0x8 lma 0x895c Loading section .data, size 0x23c lma 0x8964 Start address 0x32e0, load size 35744 Transfer rate: 42 KB/sec, 916 bytes/write. Section .text, range 0x0 -- 0x895c: matched. Section .ARM.exidx, range 0x895c -- 0x8964: matched. Section .data, range 0x8964 -- 0x8ba0: matched. Kill the program being debugged? (y or n) [answered Y; input not from terminal] If I don't do #define MYBOARDNRF5 then PlatformIO complains about undefined reference to 'g_ADigitalPinMap', which is in compat_pin_mapping.h and is called from MyBoardNRF5.cpp when MYBOARDNRF5 is defined. But I see that your variant.h/.cpp is different than the ones coming with ArduinoHwNRF5, which I'm using. Maybe try your version instead and see what happens...

85
Online

10.9k
Users

11.0k
Topics

112.1k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1