Windows GUI/Controller for MySensors

[novicit]

@tekka, problem solved! I took a debug log from the node per your suggestion and was surprised to get:
radio init fail
radio init fail
radio init fail
This of course surprised me after it just finished downloading 20kb+. Turns out after I made the first test of OTA which worked fine, my home network automatically synchronized my laptops & desktop. This brought over a copy of myconfig.h which had softspi enabled! (I had been setting up the gateway on a different computer). So when I went to OTA on the second and third nodes it picked up the synched myconfig.h. Ugh, such little strange things that take so much time to find.
@tekka, my apologies for using some of your time. And my Thanks for your great work and sharing with the community!! Hopefully others will avoid similar mistakes by reading this.

[korttoma]

Hi @tekka , I'm trying to create a simple thermostat device and I'm usually using your fantastic controller for prototype testing and debugging. Now I would need the possibility to send setpoint values from the controller and the current version of MYSController does not seem to support the following:

V_HVAC_SETPOINT_COOL 44 HVAC cold setpoint S_HVAC
V_HVAC_SETPOINT_HEAT 45 HVAC/Heater setpoint S_HVAC, S_HEATER
V_HVAC_FLOW_MODE 46 Flow mode for HVAC ("Auto", "ContinuousOn", "PeriodicOn") S_HVAC

I would greatly appreciate it is these features were implemented to your fantastic controller also.

Best regards,
Tomas

[mvader]

sorry if this has been asked before.
but I have a nano with mySbootloader installed and when i look at it in the serial monitor its just all gibberish.
i tried different speeds, but still the same.
is it not possible if you have that bootloader installed? or do i need to do something else.?
thx

[tekka]

@korttoma is implemented in 0.1.2.284 - release pending

[tekka]

@mvader this is not related to MYSBootloader. Try doubling the baud rate setting, i.e. 230400....

[Anticimex]

@tekka Would it be possible in a future version to have the controller save the detected network nodes? Right know, I have to re-present the nodes in order for them to appear properly in the tree every time MYSController is restarted since it starts up with an empty tree.

[rubal]

Hi @tekka , I've gone through the steps in your guide using MQTTGateway as gw sketch.
When I start my new node (burned with mysbootloader) I only see the repeating message "FIND_PARENT" in MySensor Debug window and "RX 0;0;3;0;9;read: 0-0-255 s=255,c=3,t=7,pt=0,l=0,sg=0:" in the MYSController Debug window.
The message appears every time the led is blinking on the node (approx every 2 seconds).

Any idea why it doesn't request node id? Have also tried with AutoID without success.

Thx!

[tekka]

@Anticimex is implemented in the upcoming release :)

[tekka]

@rubal MYSController does not support MQTT gw. Please use a different controller or change to a serial/tcp gw.

[Anticimex]

@tekka sweet! Any ETA on the next release?

[tekka]

@Anticimex wanna beta-test? ;)

[Anticimex]

@tekka for sure :)

[mvader]

@tekka - i do :) i use it every day

[petewill]

@cdr said:

I changed the channel in the mysensors config.h to 77, this was the reason no node would ever show up since the default mysbootloader uses the default channel 76.

I think I am running into the same thing. How did you fix this? I have many nodes so switching back to 76 is not a good option for me.

[cdr]

@petewill said:

running into the sam

You can edit myconfig.h and have te recompile after change.

[petewill]

@cdr I've never recompiled a bootloader before but when I did some searching it seems that I need the .c file to do this. Maybe I'm missing something and I can recompile the .hex? How did you end up doing it? Thanks!

[petewill]

I did some more testing and my issue definitely appears to be a result of changing the channel in MyConfig.h. I just built a serial gateway with channel 76 selected and everything worked perfectly. The only problem is I have over 20 nodes located throughout my house so re-uploading the code so they use that channel is not something I'd like to do if I can avoid it. Does anyone know how I can recompile the bootloader so I can change the channel?

I tried the files @siklosi posted here http://forum.mysensors.org/topic/2319/how-to-make-complie-mysbootloader/7 but it did not work.

[niccodemi]

in firmware_config.csv file what is the first column "type" for? And where do I get "type" codes?

[tekka]

@niccodemi type can be any numeric value used to identify a specific firmware type - this value (together with FW version and the FW CRC) is used to automatically update the nodes.

[niccodemi]

@petewill did you have any success finding out how to change default channel?