After changing IRQ pin in Mysensors setup everything falls apart

[Richard van der Plas]

Issue partially resolved (scroll down for info)

Steps Taken:
stopped the gateway,
renamed the MySensors folder
Followed the instalation steps for branch development.
Problem i get now is that My Gatway receives all data as normally, but every send from the GW gets a NACK
Small Snippet:

an 20 13:17:44 raspberrypi mysgw: TSF:MSG:FPAR REQ,ID=4
Jan 20 13:17:44 raspberrypi mysgw: TSF:CKU:OK,FCTRL
Jan 20 13:17:44 raspberrypi mysgw: TSF:MSG:GWL OK
Jan 20 13:17:44 raspberrypi mysgw: !TSF:MSG:SEND,0-0-4-4,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0
Jan 20 13:17:44 raspberrypi mysgw: TSF:MSG:READ,3-3-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
Jan 20 13:17:44 raspberrypi mysgw: TSF:MSG:PINGED,ID=3,HP=1
Jan 20 13:17:44 raspberrypi mysgw: !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=NACK:1
Jan 20 13:17:46 raspberrypi mysgw: TSF:MSG:READ,4-4-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
Jan 20 13:17:46 raspberrypi mysgw: TSF:MSG:BC
Jan 20 13:17:46 raspberrypi mysgw: TSF:MSG:FPAR REQ,ID=4
Jan 20 13:17:46 raspberrypi mysgw: TSF:CKU:OK,FCTRL
Jan 20 13:17:46 raspberrypi mysgw: TSF:MSG:GWL OK
Jan 20 13:17:46 raspberrypi mysgw: !TSF:MSG:SEND,0-0-4-4,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0
Jan 20 13:17:48 raspberrypi mysgw: TSF:MSG:READ,4-4-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
Jan 20 13:17:48 raspberrypi mysgw: TSF:MSG:BC
Jan 20 13:17:48 raspberrypi mysgw: TSF:MSG:FPAR REQ,ID=4
Jan 20 13:17:48 raspberrypi mysgw: TSF:CKU:OK,FCTRL
Jan 20 13:17:48 raspberrypi mysgw: TSF:MSG:GWL OK

more log:
[https://hastebin.com/isedudoren.swift](link url)
It seems to recieve stuff, but all sending gets a NACK back

i went from
MySensors Library v2.2.0-beta
to
MySensors Library v2.2.0-rc.2

Going back to the stable to test, but that gave me:

mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG--Q,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT
mysgw: TSM:FAIL:RE-INIT

As read in the manual the stable version hass issues with jessie.
Also updated 1 node to the dev version of the arduino library. and cleared the eeprom of that one
his debug shows:

        |___/                      2 /*!< Major release version*/.2 /*!< Minor release version*/.0 /*!< Patch version*/-rc.2

23 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2 /*!< Major release version*/.2 /*!< Minor release version*/.0 /*!< Patch version*/-39 TSM:INIT
40 TSF:WUR:MS=0
48 TSM:INIT:TSP OK
49 TSM:INIT:STATID=8
51 TSF:SID:OK,ID=8
53 TSM:FPAR
89 TSF:MSG:SEND,8-8-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2097 !TSM:FPAR:NO REPLY
2099 TSM:FPAR
2135 TSF:MSG:SEND,8-8-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4143 !TSM:FPAR:NO REPLY
4145 TSM:FPAR
4180 TSF:MSG:SEND,8-8-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6189 !TSM:FPAR:NO REPLY
6191 TSM:FPAR
6226 TSF:MSG:SEND,8-8-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8235 !TSM:FPAR:FAIL

Seeing everything running for a while shows my sensor wich i updated to the beta lib, keeps being searched through a repeater node (which i nowhere near atm).

What to do now ?
Small update, reverted back to 2.2.0 beta without IRQ configured and now i still have the same strange thing:

mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0

mysgw: TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:

mysgw: Client 0: 4;1;1;0;2;0
mysgw: !TSF:MSG:SEND,0-0-4-4,s=1,c=1,t=2,pt=0,l=1,sg=0,ft=0,st=NACK:0

Again a small update, added --my-rf24-pa-level=RF24_PA_LOW to the command.
That fixed the issue
I thought a Pi3 could handle the power on the 5V rail with a regulator to 3.3 ....

[gohan]

If it is a standard nrf24 it can, if it is a PA lna you need an additional regulator. In both cases a good capacitor is needed on the radio vcc

[Richard van der Plas]

Its a PA, used a regulator from 5volt Pi3 pin to 3.3 to the NRF24 and a capacitor on the VCC of the radio (47uF)

[gohan]

That's odd, I have a PA lna that uses an Ams1117 regulator and 2 4.7uF caps, it is set to max power and it works fine

[Richard van der Plas]

@gohan said in After changing IRQ pin in Mysensors setup everything falls apart:

Ams1117

Did u user a higher power source maybe? im capped out on 2.1amps on my Pi3 power source.
i use a LD117

[gohan]

The RPI3 usually draws between 0.2 to 0.7A so you should be fine on that side.