Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

debug info for radio (rfm69)

copperleaf last edited by

I'm in the process of constructing a couple of development sensors and am looking to confirm that they radio is properly connected.

Is there any debug info that can confirm (or reject) that I have an rfm69 correctly connected to my arduino?

Regards,
Bill
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by mfalkvidd @copperleaf

Hi @copperleaf, welcome to the MySensors community!

Yes. TSM INIT FAIL means the microcontroller cannot communicate with the radio. TSM INIT OK means communication with the radio is good.

Detailed info on log messages: https://www.mysensors.org/apidocs/group__MyTransportgrp.html#details

More useful info for troubleshooting: https://forum.mysensors.org/topic/666/debug-faq-and-how-ask-for-help/
Reply Quote 0
1 Reply Last reply
copperleaf last edited by

Thanks for the info. That really helped!
Reply Quote 1
1 Reply Last reply

3
Posts

924
Views

Log in to reply

Suggested Topics

MQTT GW - QOS
Development • • Soloam

7

0
Votes

7
Posts

1337
Views

Hi @Soloam, not sure if you managed to solve your problem. I would recommend using Mosquitto MQTT broker open source or Pro version since they both support all MQTT QoS levels (including QoS 0, QoS 1, QoS 2).
PlatformIO, nRF52832 and MyBoardNRF5
Development • • Stig

10

0
Votes

10
Posts

51
Views

@electrik upload_port does not specify the target. It just selects if you'll use the gdb port or the uart port from the BMP. The target I'm talking about is what comes up when trying to do upload. Configuring upload protocol... AVAILABLE: blackmagic, cmsis-dap, jlink, nrfjprog, nrfutil, stlink CURRENT: upload_protocol = blackmagic Looking for BlackMagic port... Auto-detected: COM2 Uploading .pio\build\MyBoardNRF5\firmware.hex Target voltage: 3.45V Available Targets: No. Att Driver 1 Nordic nRF52 M3/M4 2 Nordic nRF52 Access Port 0x000020d8 in transportProcessFIFO() () Loading section .text, size 0x895c lma 0x0 Loading section .ARM.exidx, size 0x8 lma 0x895c Loading section .data, size 0x23c lma 0x8964 Start address 0x32e0, load size 35744 Transfer rate: 42 KB/sec, 916 bytes/write. Section .text, range 0x0 -- 0x895c: matched. Section .ARM.exidx, range 0x895c -- 0x8964: matched. Section .data, range 0x8964 -- 0x8ba0: matched. Kill the program being debugged? (y or n) [answered Y; input not from terminal] If I don't do #define MYBOARDNRF5 then PlatformIO complains about undefined reference to 'g_ADigitalPinMap', which is in compat_pin_mapping.h and is called from MyBoardNRF5.cpp when MYBOARDNRF5 is defined. But I see that your variant.h/.cpp is different than the ones coming with ArduinoHwNRF5, which I'm using. Maybe try your version instead and see what happens...
Node to node communication fails if gateway is not reachable
Development • • Heizelmann

30

0
Votes

30
Posts

5409
Views

the Node To Node must be seen as a Gateway to node the controller is not mandatory. so we rethink the topology. Gateway (node0) <---> Node1 <---> Node2 <---> 3.. 4... The Gateway in 2022/2023 must be used, how to do!!?!! ...... a Node Useful (yes an old message, but to refresh the ideas ) happy holidays to you all
Please I need some help
Development • • Emmanuel Abraham

15

0
Votes

15
Posts

127
Views

@gulshan212 how can i do this by using mysensors library coz i need also to save battery power.
Compilation failure
Development • • mtedds

3

0
Votes

3
Posts

22
Views

Wow - given the age of the most recent messages on here, I wondered if I would get a response. Many thanks for responding so quickly and my problem is resolved. [ Note I now also have PlatformIO installed and that compiled the sketch at the first attempt. I can't work out which version of the board it is using, as it uses different naming conventions, but I think it is the most recent. ]
Help, version 2.4-alpha, PI-4 64bits & Mac OS
Development • 2.4 pi 4 64bits macos • • briseis

2

0
Votes

2
Posts

14
Views

@briseis I would just switch back to 2.3.2 I also believe 2.4 on the gateway should work with nodes on 2.3.2. what kind of errors did you get when doing this?
MYSBootloader 1.3 pre-release & MYSController 1.0.0beta
Development • ota myscontroller mysbootloader • • tekka

196

13
Votes

196
Posts

84949
Views

If anyone is getting "Property 'bootloader.tool.' is undefined" error with arduino 2.x when trying to burn bootloader, then you just have to add another row in bold below to boards.txt file MYSBL.upload.tool=avrdude MYSBL.upload.protocol=arduino MYSBL.upload.maximum_size=30720 MYSBL.upload.maximum_data_size=2048 MYSBL.bootloader.tool=avrdude MYSBL.bootloader.tool.default=avrdude
433 mhz from Arduino to Raspberry
Development • • martin1234567

3

0
Votes

3
Posts

18
Views

I would recommend to switch to a nrf24l01 or rfm69/95, where you will have bidirectional communication and you can use the mysensors framework

78
Online

10.9k
Users

11.0k
Topics

112.1k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1