Motion/actuator sensor

[Hausner]

Hi

I need some help now. I have been staring at the below code for quiet some time now, but I just can find the error.

The code should be sending a tripped signal to the controller, and the controller should return an ON/OFF to 1 of the 2 actuators. I can control the actuators just fine ON/OFF from the controller, but the motion sensor then start to flip HIGH/LOW at the interval assigned from the sensitivity potmeter.

Here is the code

  #include <MySensor.h>
  #include <SPI.h>

 #define RELAY_1 6  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
 #define NUMBER_OF_RELAYS 2 // Total number of attached relays
 #define RELAY_ON 1  // GPIO value to write to turn on attached relay
 #define RELAY_OFF 0 // GPIO value to write to turn off attached relay

  // Motion sensor defs
  unsigned long SLEEP_TIME = 10000; // Sleep time between reports (in milliseconds)
 #define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
 #define INTERRUPT DIGITAL_INPUT_SENSOR-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define CHILD_ID 3   // Id of the sensor child
volatile int state = LOW;
boolean lockLow = true;
boolean lastTripped = 0;

MySensor gw;
MyMessage msgMotion(CHILD_ID, V_TRIPPED);
//MyMessage msgRelay(CHILD_ID, V_LIGHT);
MyMessage msg(CHILD_ID, V_LIGHT);

void setup()  
{   
// Initialize library and add callback for incoming messages
  gw.begin(incomingMessage, AUTO, true);
  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo("Relay/Motion Sensor", "1.0");

  // Fetch relay status
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
// Register all sensors to gw (they will be created as child devices)
gw.present(sensor, S_LIGHT);
// Then set relay pins in output mode
pinMode(pin, OUTPUT);   
// Set relay to last known state (using eeprom storage) 
digitalWrite(pin, gw.loadState(sensor)?RELAY_ON:RELAY_OFF);
 }

  pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
 // Register all sensors to gw (they will be created as child devices)
gw.present(CHILD_ID, S_MOTION);
// attachInterrupt(DIGITAL_INPUT_SENSOR, ON, CHANGE);
delay(30000);
}


void loop() 
{
// Alway process incoming messages whenever possible
gw.process();

boolean tripped = (digitalRead(DIGITAL_INPUT_SENSOR) == HIGH);
if (lastTripped != tripped ) {
gw.send(msgMotion.set(tripped?"1":"0")); // Send new state
lastTripped=tripped;
 }
}


void incomingMessage(const MyMessage &message) {
// We only expect one type of message from controller. But we better check anyway.
 if (message.type==V_LIGHT) {
 // Change relay state
 digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
 // Store state in eeprom
 gw.saveState(message.sensor, message.getBool());
 // Write some debug info
 Serial.print("Incoming change for sensor:");
 Serial.print(message.sensor);
 Serial.print(", New status: ");
 Serial.println(message.getBool());
 }
}

With the above code I get this on the sensor serial:

send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:0
send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:1
send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:0
send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:1
send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:0
send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:1
send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:0
send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:1
send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:0
send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:1
send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:0
send: 30-30-0-0 s=3,c=1,t=16,pt=0,l=1,st=ok:1

every ~4 second.. PLS help

[jendrush]

@Hausner Have you considered sensor failure?

[BulldogLowell]

@Hausner said:

but the motion sensor then start to flip HIGH/LOW at the interval assigned from the sensitivity potmeter.

so you want to trigger on only one side of the motion sensor's output?

[Hausner]

@jendrush said:

@Hausner Have you considered sensor failure?

Yes, but I've tried to load the default actuator and motion sensor sketches from the library, and both works fine, so I don't think I have faulty sensors.

[Hausner]

Turned out that the Nano was faulty.

I rebuilded the setup with a new Nano, and it's now working as designed