Weather Station with Scene Activator!!!

[korttoma]

@BulldogLowell

Hi Jim, Yeah I finished it. there is a few posts about it over in heks scene controller thread -> http://forum.mysensors.org/topic/446/scene-controller

[BulldogLowell]

Tomas,

My business has kept me away from this, I guess I didn't notice how far along you took it... brilliant job!

I'll check in when it's done.

Thanks mate.

jim

[BulldogLowell]

Tomas,

Again, thanks for your example. I have to say, it helped a lot.

I am however struggling with radio communication it seems and I am wondering at this point what I am doing wrong, having spent a couple hours trying to find my errors.

Would you mind to take a look for anything you may see:

#define STATES 7
#define HUMIDITY_SENSOR_DIGITAL_PIN 4
#define DEBUG

#ifdef DEBUG
#define DEBUG_SERIAL(x) Serial.begin(x)
#define DEBUG_PRINT(x) Serial.print(x)
#define DEBUG_PRINTLN(x) Serial.println(x)
#else
#define DEBUG_SERIAL(x)
#define DEBUG_PRINT(x) 
#define DEBUG_PRINTLN(x) 
#endif

#include <Wire.h>
#include <Time.h>
#include <SPI.h>
#include <MySensor.h>
#include <LiquidCrystal_I2C.h>
#include <DHT.h> 
//
#define RADIO_ID 11
#define CHILD_ID_SCENE 3
//
LiquidCrystal_I2C lcd(0x27,16,2);  // set the LCD address to 0x20 for a 16 chars and 2 line display
//
void (*lcdDisplay[STATES])();
//
byte state = 0;
byte lastState;
byte timeCounter = 0;
unsigned long lastTime;
unsigned long refreshInterval = 3000UL;
unsigned long lastClockSet;
boolean isMessage = false;
float insideTemperature;
float humidity;
int OutdoorTemp = -99;
int OutdoorHumidity = -99;
int todayHigh = -99; 
int todayLow = -99;
String conditions = "Not yet Reported";
String FreeMessage = "No Message recieved"; //*****
int ledStatus = 1;// to toggle LCD backlight led
//int ledLevel = 254;
boolean buttonPushed = false;
//
MySensor gw;
DHT dht;
//
MyMessage msgOn(CHILD_ID_SCENE, V_SCENE_ON);
MyMessage msgOff(CHILD_ID_SCENE, V_SCENE_OFF);
MyMessage msgVAR1(CHILD_ID_SCENE, V_VAR1);
MyMessage msgVAR2(CHILD_ID_SCENE, V_VAR2);
MyMessage msgVAR3(CHILD_ID_SCENE, V_VAR3);
MyMessage msgVAR4(CHILD_ID_SCENE, V_VAR4);
MyMessage msgVAR5(CHILD_ID_SCENE, V_VAR5);
//
void setup()  
{ 
  DEBUG_SERIAL(115200);
  DEBUG_PRINTLN(F("Serial started"));
  attachInterrupt(1, PushButton, CHANGE);
  //
  lcdDisplay[0] = lcdDisplay0;
  lcdDisplay[1] = lcdDisplay1;
  lcdDisplay[2] = lcdDisplay2;
  lcdDisplay[3] = lcdDisplay3;
  lcdDisplay[4] = lcdDisplay4;
  lcdDisplay[5] = lcdDisplay5;
  lcdDisplay[6] = lcdDisplay6;
  //
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN);
  gw.begin(TempStatus, RADIO_ID);
  gw.sendSketchInfo("WeatherClock", "1.0");
  gw.present(CHILD_ID_SCENE, S_SCENE_CONTROLLER);
  int clockTimer;
  while(timeStatus() != timeSet && clockTimer < 10)
  {
    gw.requestTime(receiveTime);
    Serial.println("getting Time");
    delay(500);
    clockTimer++;
  }
  //
  lcd.init();
  lcd.clear();
  lcd.backlight();
  lcd.setCursor(0, 0);
  lcd.print("Hello World!!!");
  delay(2000);
  lcd.clear();
  lastTime = millis();
}
void loop()      
{
  gw.process();
  if (millis() - lastClockSet >= 60000UL)
  {
    gw.requestTime(receiveTime);
    lastClockSet = millis();
  }
  if (millis() - lastTime >= refreshInterval)
  {
    state++;
    if (state > STATES - 1) state = 0;
    DEBUG_PRINTLN(F("State:")); 
    DEBUG_PRINTLN(state);
    lastTime += refreshInterval;
    getTempHumidity();
  }
  if (state != lastState) 
  {
    fastClear();
    lcdDisplay[state]();
  }
  lastState = state;
  if (buttonPushed)
  {
    activateScene();
  }
}
void fastClear()
{
  lcd.setCursor(0,0);
  lcd.print("                ");
  lcd.setCursor(0,1);
  lcd.print("                ");
}
//
void lcdDisplay0()
{
  lcd.setCursor(0,0);
  lcd.print(F("Time: "));
  if (hourFormat12() < 10) lcd.print("0");
  lcd.print(hourFormat12());
  lcd.print(":");
  if (minute() < 10) lcd.print("0");
  lcd.print(minute());
  DEBUG_PRINT(F("Time:"));
  DEBUG_PRINTLN(hourFormat12());
  lcd.setCursor(0,1);
  lcd.print(F("Date: "));
  if (month() < 10) lcd.print("0");
  lcd.print(month());
  lcd.print("/");
  if (day() < 10) lcd.print("0");
  lcd.print(day());
  lcd.print("/");
  lcd.print(year());
  DEBUG_PRINTLN(F("Date: 01.11.2014"));
}
void lcdDisplay1()
{
  lcd.setCursor(0,0);
  lcd.print(F("Indoor Temp:"));
  lcd.print(int(insideTemperature));
  lcd.print(char(223));
  DEBUG_PRINT(F("Indoor Temp:")); 
  DEBUG_PRINT(int(insideTemperature)); 
  DEBUG_PRINTLN(F("F"));
  lcd.setCursor(0,1);
  lcd.print("   Humidity:");
  lcd.print(int(humidity));
  lcd.print(F("%"));
  DEBUG_PRINT("   Humidity:");
  DEBUG_PRINT(int(humidity));
  DEBUG_PRINTLN(F("F"));
}
void lcdDisplay2()
{
  lcd.setCursor(0,0);
  lcd.print("Outdoor Temp:"); 
  lcd.print(OutdoorTemp); 
  lcd.print(char(223));
  DEBUG_PRINT(F("Outdoor Temp:"));
  DEBUG_PRINTLN(OutdoorTemp);
  lcd.setCursor(0,1);
  lcd.print(F("    Humidity:")); 
  lcd.print(OutdoorHumidity); 
  lcd.print(F("%"));
  DEBUG_PRINT(F("    Humidity:"));
  DEBUG_PRINTLN(OutdoorHumidity);
}
void lcdDisplay3()
{
  lcd.setCursor(0,0);
  lcd.print(F("Today's HI:"));
  lcd.print(todayHigh); 
  lcd.print(char(223));
  DEBUG_PRINT(F("Today's HIGH"));
  DEBUG_PRINTLN(todayHigh);
  lcd.setCursor(0,1);
  lcd.print(F("        LO:"));
  lcd.print(todayLow); 
  lcd.print(char(223));
  DEBUG_PRINT(F("Today's LOW"));
  DEBUG_PRINTLN(todayLow);
}
void lcdDisplay4()
{
  lcd.setCursor(0,0);
  lcd.print(F("Today's Weather is"));
  DEBUG_PRINTLN(F("Today's Weather:"));
  lcd.setCursor(0,1);
  lcd.print(conditions);
  DEBUG_PRINTLN(F("EXAMPLE"));
}
void lcdDisplay5()
{
  if (isMessage)
  {
    lcd.setCursor(0,0);
    lcd.print(F("****Message****"));
    DEBUG_PRINTLN(F("****Message****"));
    lcd.setCursor(0,1);
    lcd.print(F("Custom Message"));
    DEBUG_PRINTLN(F("Custom Message"));
  }
  else
  {
    lcd.setCursor(0,0);
    lcd.print(F("****Message****"));
    DEBUG_PRINTLN(F("****Message****"));
    lcd.setCursor(0,1);
    lcd.print(F("Have a Nice Day"));
    DEBUG_PRINTLN(F("Have a Nice Day"));
  }
}
void lcdDisplay6()
{
  lcd.setCursor(0,0);
  lcd.print(F(" Weather & Time "));
  DEBUG_PRINTLN(F(" Weather & Time "));
  lcd.setCursor(0,1);
  lcd.print(F("by BulldogLowell"));
  DEBUG_PRINTLN(F("by BulldogLowell")); 
}

//
void getTempHumidity()
{
  insideTemperature = dht.toFahrenheit(dht.getTemperature());
  if (isnan(insideTemperature)) 
  {
    DEBUG_PRINTLN(F("Failed reading temperature from DHT"));
  } 
  humidity = dht.getHumidity();
  if (isnan(humidity)) 
  {
    DEBUG_PRINTLN(F("Failed reading humidity from DHT"));
  } 
}
//
void receiveTime(unsigned long time)
{
  DEBUG_PRINTLN(F("Time value received: "));
  DEBUG_PRINTLN(time);
  setTime(time);
}
//
void PushButton()
{
  static unsigned long last_interrupt_time = 0;
  unsigned long interrupt_time = millis();
  if (interrupt_time - last_interrupt_time > 200)
  {
    buttonPushed = true;
  }
  last_interrupt_time = interrupt_time;
}
//
void activateScene()
{
  DEBUG_PRINTLN(F("ButtonPushed"));
  fastClear();
  for (byte i = 0; i < 10; i++)
  {
    lcd.noBacklight();
    delay(50);
    lcd.backlight();
    delay(50);
  }
  lcd.setCursor(0,0);
  lcd.print(F(" A/C Boost Mode "));
  lcd.setCursor(0,1);
  lcd.print(F("**** ACTIVE ****"));
  delay(2000);
  buttonPushed = false;
  lastTime = millis(); //Reset the timer to even out display interval
}
//
void TempStatus(const MyMessage &message)
{
  if (message.type == V_VAR1)
  {
    OutdoorTemp = atoi(message.data);
    DEBUG_PRINTLN(F("OutdoorTemp recieved:"));
    DEBUG_PRINTLN(OutdoorTemp);
  }
  if (message.type == V_VAR2)
  {
    OutdoorHumidity = atoi(message.data);
    DEBUG_PRINT(F("OutdoorHumidity recieved:"));
    DEBUG_PRINTLN(OutdoorHumidity);
  }
  if (message.type == V_VAR3)
  {
    todayLow = atoi(message.data);
    DEBUG_PRINT(F("Today's LOW:"));
    DEBUG_PRINTLN(todayLow);
  }

  if (message.type == V_VAR4)
  {
    todayHigh = atoi(message.data);
    DEBUG_PRINT(F("Today's HIGH:"));
    DEBUG_PRINTLN(todayHigh);
  }
  if (message.type == V_VAR5)
  {
    conditions = String(message.data);
  }
}

my error looks like this:

Serial started
sensor started, id 11
send: 11-11-0-0 s=255,c=0,t=17,pt=0,l=3,st=fail:1.4
send: 11-11-0-0 s=255,c=3,t=6,pt=1,l=1,st=fail:0
send: 11-11-0-0 s=255,c=3,t=11,pt=0,l=12,st=fail:WeatherClock
send: 11-11-0-0 s=255,c=3,t=12,pt=0,l=3,st=fail:1.0
send: 11-11-0-0 s=3,c=0,t=25,pt=0,l=3,st=fail:1.4
send: 11-11-0-0 s=255,c=3,t=1,pt=0,l=3,st=fail:1.4
getting Time
send: 11-11-0-0 s=255,c=3,t=1,pt=0,l=3,st=fail:1.4
send: 11-11-255-255 s=255,c=3,t=7,pt=0,l=0,st=fail:
getting Time
send: 11-11-0-0 s=255,c=3,t=1,pt=0,l=0,st=fail:
getting Time
send: 11-11-0-0 s=255,c=3,t=1,pt=0,l=0,st=fail:
getting Time
send: 11-11-0-0 s=255,c=3,t=1,pt=0,l=0,st=fail:
getting Time
send: 11-11-0-0 s=255,c=3,t=1,pt=0,l=0,st=fail:
getting Time
send: 11-11-0-0 s=255,c=3,t=1,pt=0,l=0,st=fail:
getting Time
State:
1
Indoor Temp:71F
   Humidity:46F
State:
2
Outdoor Temp:-99
    Humidity:-99
State:
3
Today's HIGH-99
Today's LOW-99
State:

My lua code server-side is this:

local temp = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 60)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_1", value=temp}, 85)

 local humid = luup.variable_get("urn:micasaverde-com:serviceId:HumiditySensor1","CurrentLevel", 63)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_2", value=humid}, 85)

local low = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 61)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_3", value=low}, 85)

local high = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 62)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_4", value=high}, 85)

local conditions = luup.variable_get("urn:upnp-org:serviceId:Weather1","CurrentTemperature", 59)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_5", value=conditions}, 85)

[BulldogLowell]

I added delays in the lua code and that seemed to help a lot:

local temp = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 60)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_1", value=temp}, 85)

luup.sleep(750)

local humid = luup.variable_get("urn:micasaverde-com:serviceId:HumiditySensor1","CurrentLevel", 63)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_2", value=humid}, 85)

luup.sleep(750)

local low = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 61)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_3", value=low}, 85)

luup.sleep(750)

local high = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 62)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_4", value=high}, 85)

luup.sleep(750)

local conditions = luup.variable_get("urn:upnp-org:serviceId:Weather1","CurrentTemperature", 59)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_5", value=conditions}, 85)

still struggling with this, however:

if (message.type == V_VAR5)
{
  conditions = String(message.data);
  DEBUG_PRINT(F("Received today's Conditions:"));
  DEBUG_PRINTLN(conditions);
}

not returning the present conditions....

[BulldogLowell]

also noticed that variable5 (V_VAR5) does not show up here (in device 85):

[korttoma]

@BulldogLowell

I do have all 5 variables listed under my scene-controler device. Do you still get the failed for getting time in your serial print? Seems like you might have "general" communication issues, you have cap on the radio? Try a different power source or temporarily move your device closer to the gateway. I had some similar problems when trying to use the PA+LNA radio module so I switched to a regular one and that one works fine. I wanted to use the PA+LNA version because the device is quite far from GW and I did not think the regular one could handle the distance but it did.

Thanks for showing me how to add a delay to the lua code btw, I newer figured that out so I only ewer sent two variables at a time. Btw, does the delay affect vera in any way? I thought I read somewhere that the unit does not do anything during sleep.

[BulldogLowell]

Tomas,

(and I'm opening this up to anyone who knows how to work messages into more than one device )

well, I figured out the problem of "conditions" which was the wrong serviceId in the lua coding for that variable.

Regarding the delay, if you luup.sleep() for anything that approaches a second, your Vera will restart :( so I figure that the 750ms would be OK. I am concerned about it being incommunicado so often, so I'll probably put the transmissions into different scenes.

I definitely have a communication issue... and it bothers me a bit. I have all that, capacitors on the antenna, etc. I think I have a bad node and its likely my PhoneyTV. Whenever I 'manually' toggle the lights using the Vera interface, it seems to lock up the gateway.... More on that to come.

I really appreciate your sharing the code. In retrospect, it seems that the latest mySensors implementation is a lot more elegant with respect to setting up communications like these, but the example helped immensely.

I'm now tripping up on using variables in the second device: Can I recycle the variables here (e.g. V_VAR1) or must I create another instance of gw?

MySensor gw;
DHT dht;
//
MyMessage msgOn(CHILD_ID_SCENE, V_SCENE_ON);
MyMessage msgOff(CHILD_ID_SCENE, V_SCENE_OFF);
MyMessage msgVAR1(CHILD_ID_SCENE, V_VAR1);// outdoor temperature
MyMessage msgVAR2(CHILD_ID_SCENE, V_VAR2);// outdoor humidity
MyMessage msgVAR3(CHILD_ID_SCENE, V_VAR3);//today's low
MyMessage msgVAR4(CHILD_ID_SCENE, V_VAR4);// today's high
MyMessage msgVAR5(CHILD_ID_SCENE, V_VAR5);//conditions
//
MyMessage lightMsg(CHILD_ID_LED, V_LIGHT);
//MyMessage msgMOTD(CHILD_ID_LED, V_VAR1); // message of the day//<<<<<<<<<<<<<<<<<
//MyMessage msgAlarm(CHILD_ID_LED, V_VAR2); // alarm status//<<<<<<<<<<<<<<<<<<<<<<<<
//MyMessage msgBrite(CHILD_ID_LED, V_VAR3); // led briteness (nice idea!!!!)<<<<<<<<<<<<<<<
//

setup() bit:

   //
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN);
  gw.begin(getVariables, RADIO_ID);
  gw.sendSketchInfo("WeatherClock", "1.0");
  gw.present(CHILD_ID_SCENE, S_SCENE_CONTROLLER);
  gw.present( CHILD_ID_LED, S_LIGHT);
  int clockTimer;

used here:

void getVariables(const MyMessage &message)
{  
  if (message.type == V_VAR1)
  {
    OutdoorTemp = atoi(message.data);
    DEBUG_PRINTLN(F("OutdoorTemp recieved:"));
    DEBUG_PRINTLN(OutdoorTemp);
  }
  if (message.type == V_VAR2)
  {
    OutdoorHumidity = atoi(message.data);
    DEBUG_PRINT(F("OutdoorHumidity recieved:"));
    DEBUG_PRINTLN(OutdoorHumidity);
   }
   if (message.type == V_VAR3)
  etc...

any advice?

best,

Jim

[korttoma]

Did not try it but how about this:

void getVariables(const MyMessage &message)
    {
        if (message.sensor==CHILD_ID_SCENE){  
            if (message.type == V_VAR1){
                OutdoorTemp = atoi(message.data);
                DEBUG_PRINTLN(F("OutdoorTemp recieved:"));
                DEBUG_PRINTLN(OutdoorTemp);
           }
           if (message.type == V_VAR2){
               OutdoorHumidity = atoi(message.data);
               DEBUG_PRINT(F("OutdoorHumidity recieved:"));
               DEBUG_PRINTLN(OutdoorHumidity);
          }
          if (message.type == V_VAR3)
              etc...

        if (message.sensor==CHILD_ID_LED){  
            if (message.type == V_VAR1){
                DayMessage = atoi(message.data);
                DEBUG_PRINTLN(DayMessage);
           }
           if (message.type == V_VAR2){
               AlarmStatus = atoi(message.data);
               DEBUG_PRINT(F("House is:"));
               DEBUG_PRINTLN(AlarmStatus);
          }
          if (message.type == V_VAR3)
             etc...

[BulldogLowell]

@korttoma

thanks, I'll give it a shot.

another method for dispatching messages (with delays in between) from Vera with this type of lua function:

(thanks to @RexBeckett for the assistance)

function SendWeatherData(strstep)
	local step = tonumber(strstep)
	if step == 1 then
		local temp = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 60)
		luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_1", value=temp}, 85)
	elseif step == 2 then
		local humid = luup.variable_get("urn:micasaverde-com:serviceId:HumiditySensor1","CurrentLevel", 63)
		luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_2", value=humid}, 85)
	elseif step == 3 then
		local low = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 61)
		luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_3", value=low}, 85)
	elseif step == 4 then
		local high = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 62)
		luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_4", value=high}, 85)
	elseif step == 5 then
		local conditions = luup.variable_get("urn:upnp-micasaverde-com:serviceId:Weather1","Condition", 59)
		luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_5", value=conditions}, 85)
	end
	step = step + 1
	if step <= 5 then
		luup.call_delay(1,tostring(step))
	end
end

SendWeatherData("1")

[korttoma]

wow, don't understand what that lua function does but I'll give it a try. Thanks @RexBeckett

[BulldogLowell]

@korttoma

"The following code calls the function SendWeatherData immediately and the function calls itself with a one second delay. Each time the function runs, it uses a step counter to chose a value to be read and sent. The step gets incremented on each run until it exceeds five after which the function stops calling itself." - rex

This way, it shouldn't affect vera's watchdog.

Rex is really helpful on matters of lua ;)

[BulldogLowell]

@korttoma

I was thinking that perhaps it may be easier/better to recycle V_VAR1 and transmit messages to the node with a leading char. then have the arduino sort out the message based on the header:

for example:

local conditions = luup.variable_get("urn:upnp-micasaverde-com:serviceId:Weather1","Condition", 59)
conditions = "#" .. conditions
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_5", value=conditions}, 85)

then sort and strip out the char arduino-side... you could move a lot more message types through one variable

new message types need to be hard coded into Arduino and Vera, so if we want to expand the data flow... it becomes easier this way, no? Perhaps there is a better message type to use for this type of effort...

This device is in our guest house and since I have it open I want to add capabilities like:

1: Message of the day
2: quick SMS type of message
3: alarm clock settable by mobile app
4: twitter feed

stuff like that...

[BulldogLowell]

@korttoma

Tomas, I just wanted to say thanks for the help. My (almost 100% completed) code is here and a couple of videos showing how it works:

first

link text

#define STATES 7
#define HUMIDITY_SENSOR_DIGITAL_PIN 4
#define DEBUG

#ifdef DEBUG
#define DEBUG_SERIAL(x) Serial.begin(x)
#define DEBUG_PRINT(x) Serial.print(x)
#define DEBUG_PRINTLN(x) Serial.println(x)
#else
#define DEBUG_SERIAL(x)
#define DEBUG_PRINT(x) 
#define DEBUG_PRINTLN(x) 
#endif

#include <avr/pgmspace.h>
#include <Wire.h>
#include <Time.h>
#include <SPI.h>
#include <MySensor.h>
#include <LiquidCrystal_I2C.h>
#include <DHT.h> 
//
#define RADIO_ID 11
#define CHILD_ID_SCENE 3
#define CHILD_ID_LED 4
//
LiquidCrystal_I2C lcd(0x27,16,2);  // set the LCD address to 0x27 for a 16 chars and 2 line display
//
void (*lcdDisplay[STATES])();
//
byte state = 0;
byte lastState;
byte timeCounter = 0;
unsigned long lastTime;
unsigned long refreshInterval = 3000UL;
unsigned long lastClockSet;
boolean isMessage = false;
float insideTemperature;
float humidity;
int OutdoorTemp = -99;
int OutdoorHumidity = -99;
int todayHigh = -99; 
int todayLow = -99;
String conditions = "Not yet Reported";
String tomorrowWeather = "Not yet Reported";
String messageOfTheDay = "**Hello There!**";
unsigned long motdTimer;
int ledStatus;// to toggle LCD backlight led
boolean buttonPushed = false;
//
MySensor gw;
DHT dht;
//
MyMessage msgOn(CHILD_ID_SCENE, V_SCENE_ON);
MyMessage msgOff(CHILD_ID_SCENE, V_SCENE_OFF);
MyMessage msgVAR1(CHILD_ID_SCENE, V_VAR1);// outdoor temperature
MyMessage msgVAR2(CHILD_ID_SCENE, V_VAR2);// outdoor humidity
MyMessage msgVAR3(CHILD_ID_SCENE, V_VAR3);//today's low
MyMessage msgVAR4(CHILD_ID_SCENE, V_VAR4);// today's high
MyMessage msgVAR5(CHILD_ID_SCENE, V_VAR5);//conditions
//
MyMessage lightMsg(CHILD_ID_LED, V_LIGHT);
MyMessage msgMOTD(CHILD_ID_LED, V_VAR1); // message of the day
MyMessage msgAlarm(CHILD_ID_LED, V_VAR2); // alarm status
MyMessage msgBrite(CHILD_ID_LED, V_VAR3); // led briteness (nice idea!!!!)
//
void setup()  
{ 
  DEBUG_SERIAL(115200);
  DEBUG_PRINTLN(F("Serial started"));
  attachInterrupt(1, PushButton, CHANGE);
  //
  lcdDisplay[0] = lcdDisplay0;
  lcdDisplay[1] = lcdDisplay1;
  lcdDisplay[2] = lcdDisplay2;
  lcdDisplay[3] = lcdDisplay3;
  lcdDisplay[4] = lcdDisplay4;
  lcdDisplay[5] = lcdDisplay5;
  lcdDisplay[6] = lcdDisplay6;
  //
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN);
  gw.begin(getVariables, RADIO_ID);
  gw.sendSketchInfo("WeatherClock", "1.0");
  gw.present(CHILD_ID_SCENE, S_SCENE_CONTROLLER);
  gw.present( CHILD_ID_LED, S_LIGHT);
  //
  lcd.init();
  lcd.clear();
  lcd.backlight();
  lcd.setCursor(0, 0);
  lcd.print("Syncing Time");
  lcd.setCursor(0, 1);
  int clockCounter = 0;
  while(timeStatus() == timeNotSet && clockCounter < 60)
  {
    gw.process();
    gw.requestTime(receiveTime);
    Serial.println("getting Time");
    delay(1000);
    lcd.print(".");
    clockCounter++;
    if (clockCounter > 16)
    {
      lcd.clear();
      lcd.print(F("**Failed Clock**"));
      lcd.setCursor(0,1);
      lcd.print(F("*Syncronization*"));
      delay(2000);
      break;
    }
  }
  lcd.clear();
  lastTime = millis();
}
void loop()      
{
  gw.process();
  if (millis() - lastClockSet >= 60000UL)
  {
    gw.requestTime(receiveTime);
    lastClockSet = millis();
  }
  if (millis() - lastTime >= refreshInterval)
  {
    state++;
    if (state > STATES - 1) state = 0;
    DEBUG_PRINTLN(F("State:")); 
    DEBUG_PRINTLN(state);
    lastTime += refreshInterval;
    getTempHumidity();
  }
  if (state != lastState) 
  {
    fastClear();
    lcdDisplay[state]();
  }
  lastState = state;
  if (buttonPushed)
  {
    activateScene();
  }
  if (isMessage)
  {
    if (millis() - motdTimer > 86400 * 1000UL)
    {
      isMessage = false;
    }
  }
}
void fastClear()
{
  lcd.setCursor(0,0);
  lcd.print("                ");
  lcd.setCursor(0,1);
  lcd.print("                ");
}
//
void lcdDisplay0()
{
  lcd.setCursor(0,0);
  lcd.print(F("Time: "));
  if (hourFormat12() < 10) lcd.print("0");
  lcd.print(hourFormat12());
  lcd.print(":");
  if (minute() < 10) lcd.print("0");
  lcd.print(minute());
  if (isAM()) lcd.print(F("am"));
  else lcd.print(F("pm"));
  DEBUG_PRINT(F("Time:"));
  DEBUG_PRINTLN(hourFormat12());
  lcd.setCursor(0,1);
  lcd.print(F("Date: "));
  if (month() < 10) lcd.print("0");
  lcd.print(month());
  lcd.print("/");
  if (day() < 10) lcd.print("0");
  lcd.print(day());
  lcd.print("/");
  lcd.print(year());
  DEBUG_PRINTLN(F("Date: ")); 
  DEBUG_PRINT(month()); 
  DEBUG_PRINT("/"); 
  DEBUG_PRINT(day()); 
  DEBUG_PRINT("/"); 
  DEBUG_PRINTLN(year());
}
void lcdDisplay1()
{
  lcd.setCursor(0,0);
  lcd.print(F(" Indoor Temp:"));
  lcd.print(int(round(insideTemperature)));
  lcd.print(char(223));
  DEBUG_PRINT(F("Indoor Temp:")); 
  DEBUG_PRINT(int(round(insideTemperature))); 
  DEBUG_PRINTLN(F("F"));
  lcd.setCursor(0,1);
  lcd.print("    Humidity:");
  lcd.print(int(round(humidity)));
  lcd.print(F("%"));
  DEBUG_PRINT("   Humidity:");
  DEBUG_PRINT(int(round(humidity)));
  DEBUG_PRINTLN(F("F"));
}
void lcdDisplay2()
{
  lcd.setCursor(0,0);
  lcd.print("Outdoor Temp:"); 
  lcd.print(OutdoorTemp); 
  lcd.print(char(223));
  DEBUG_PRINT(F("Outdoor Temp:"));
  DEBUG_PRINTLN(OutdoorTemp);
  lcd.setCursor(0,1);
  lcd.print(F("    Humidity:")); 
  lcd.print(OutdoorHumidity); 
  lcd.print(F("%"));
  DEBUG_PRINT(F("    Humidity:"));
  DEBUG_PRINTLN(OutdoorHumidity);
}
void lcdDisplay3()
{
  lcd.setCursor(0,0);
  lcd.print(F("Today's High:"));
  lcd.print(todayHigh); 
  lcd.print(char(223));
  DEBUG_PRINT(F("Today's High: "));
  DEBUG_PRINTLN(todayHigh);
  lcd.setCursor(0,1);
  lcd.print(F("         Low:"));
  lcd.print(todayLow); 
  lcd.print(char(223));
  DEBUG_PRINT(F("Today's Low: "));
  DEBUG_PRINTLN(todayLow);
}
void lcdDisplay4()
{
  lcd.setCursor(0,0);
  lcd.print(F("Today's Weather"));
  DEBUG_PRINTLN(F("Today's Weather: "));
  lcd.setCursor(0,1);
  lcd.print(conditions);
  DEBUG_PRINTLN(conditions);
}
void lcdDisplay5()
{
  lcd.setCursor(0,0);
  lcd.print(F("Forcast Tomorrow"));
  DEBUG_PRINTLN(F("Tomorrow's Forecast: "));
  lcd.setCursor(0,1);
  lcd.print(tomorrowWeather);
  DEBUG_PRINTLN(tomorrowWeather);
}
void lcdDisplay6()
{
  if (isMessage)
  {
    lcd.setCursor(0,0);
    lcd.print(F("**NEW  MESSAGE**"));
    DEBUG_PRINTLN(F("****Message****"));
    lcd.setCursor(0,1);
    lcd.print(messageOfTheDay);
    DEBUG_PRINTLN(messageOfTheDay);
    motdTimer = millis();
  }
  else
  {
    lcd.setCursor(0,0);
    lcd.print(F("****Welcome!****"));
    DEBUG_PRINTLN(F("****Message****"));
    lcd.setCursor(0,1);
    lcd.print(F("Have a Nice Day!"));
    DEBUG_PRINTLN(F("Have a Nice Day"));
  }
}
//
void getTempHumidity()
{
  insideTemperature = dht.toFahrenheit(dht.getTemperature());
  if (isnan(insideTemperature)) 
  {
    DEBUG_PRINTLN(F("Failed reading temperature from DHT"));
  } 
  humidity = dht.getHumidity();
  if (isnan(humidity)) 
  {
    DEBUG_PRINTLN(F("Failed reading humidity from DHT"));
  } 
}
//
void receiveTime(unsigned long time)
{
  DEBUG_PRINTLN(F("Time value received: "));
  DEBUG_PRINTLN(time);
  setTime(time);
}
//
void PushButton()
{
  static unsigned long last_interrupt_time = 0;
  unsigned long interrupt_time = millis();
  if (interrupt_time - last_interrupt_time > 200)
  {
    buttonPushed = true;
  }
  last_interrupt_time = interrupt_time;
}
//
void activateScene()
{
  DEBUG_PRINTLN(F("ButtonPushed"));
  fastClear();
  for (byte i = 0; i < 10; i++)
  {
    lcd.noBacklight();
    delay(50);
    lcd.backlight();
    delay(50);
  }
  lcd.setCursor(0,0);
  lcd.print(F(" A/C Boost Mode "));
  lcd.setCursor(0,1);
  lcd.print(F("**** ACTIVE ****"));
  delay(2000);
  buttonPushed = false;
  lastTime = millis(); //Reset the timer to even out display interval
  ledStatus = gw.loadState(CHILD_ID_LED);
  if (ledStatus > 0)
  {
    lcd.backlight();
  }
  else
  {
    lcd.noBacklight();
  }
}
//
void getVariables(const MyMessage &message)
{
  if (message.sensor == CHILD_ID_SCENE)
  { 
    if (message.type == V_VAR1)
    {
      OutdoorTemp = atoi(message.data);
      DEBUG_PRINTLN(F("OutdoorTemp recieved:"));
      DEBUG_PRINTLN(OutdoorTemp);
    }
    if (message.type == V_VAR2)
    {
      OutdoorHumidity = atoi(message.data);
      DEBUG_PRINT(F("OutdoorHumidity recieved:"));
      DEBUG_PRINTLN(OutdoorHumidity);
    }
    if (message.type == V_VAR3)
    {
      todayLow = atoi(message.data);
      DEBUG_PRINT(F("Received Today's LOW:"));
      DEBUG_PRINTLN(todayLow);
    }

    if (message.type == V_VAR4)
    {
      todayHigh = atoi(message.data);
      DEBUG_PRINT(F("Received Today's HIGH:"));
      DEBUG_PRINTLN(todayHigh);
    }
    if (message.type == V_VAR5)
    {
      String newMessage = String(message.data);
      int locator = newMessage.indexOf("@");
      newMessage = newMessage.substring(0, locator);
      conditions = newMessage;
      DEBUG_PRINT(F("Received today's Conditions:"));
      DEBUG_PRINTLN(conditions);
    }
  }
  if (message.sensor == CHILD_ID_LED)
  {
    if (message.type == V_LIGHT)
    {
      int ledState = atoi(message.data);
      if (ledState > 0)
      {
        lcd.backlight();
      }
      else
      {
        lcd.noBacklight();
      }
    }
    if (message.type == V_VAR1)
    {
      // led briteness (nice idea!!!!)
    }
    if (message.type == V_VAR2)
    {
      // Extended Forecast
      String newMessage = String(message.data);
      int locator = newMessage.indexOf("@");
      newMessage = newMessage.substring(0, locator);
      tomorrowWeather = newMessage;
      DEBUG_PRINT(F("Received Two Day Forecast:"));
      DEBUG_PRINTLN(tomorrowWeather);
    }
    if (message.type == V_VAR3)
    {
      // message of the day
      String newMessage = String(message.data);
      int locator = newMessage.indexOf("@");
      newMessage = newMessage.substring(0, locator);
      messageOfTheDay = newMessage;
      DEBUG_PRINT(F("Received Message of the Day:"));
      DEBUG_PRINTLN(messageOfTheDay);
      isMessage = true;
    }
  }
}

fixed it

[korttoma]

4 spaces in front of every line will be displayed as code. Please update your post. And I could not play the videos either.

[BulldogLowell]

@korttoma

all fixed. I had to take the text into another editor

here is the lua

 local temp = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 60)
 luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_1", value=temp}, 85)

 luup.sleep(750)

 local humid = luup.variable_get("urn:micasaverde-com:serviceId:HumiditySensor1","CurrentLevel", 63)
 luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_2", value=humid}, 85)

 luup.sleep(750)

 local low = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 61)
 luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_3", value=low}, 85)

 luup.sleep(750)

 local high = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 62)
 luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_4", value=high}, 85)

 luup.sleep(750)

 local conditions = luup.variable_get("urn:upnp-micasaverde-com:serviceId:Weather1","Condition", 59)
 luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_5", value=conditions}, 85)

 luup.sleep(750)  

 local conditions = luup.variable_get("urn:upnp-micasaverde-com:serviceId:Weather1","Forecast.1.Condition", 59)
 luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;4", variableId="VAR_2", value=conditions}, 85)

 luup.sleep(750)

[korttoma]

Nice job on the sketch Jim, I especially liked the idea with "#define DEBUG". There were allso some other ideas I will be stealing some day when I find time to update my sketch.

So I guess you did not use the function by @RexBeckett then? I could not get it to work either. I'll try your suggestion with the delays.

[BulldogLowell]

@korttoma

Thanks for your help and time, you made it a lot easier! I'm trying to write the code for an audience rather than myself so I'm focused more on what I'm putting into the sketch versus just 'getting it to work.' I'm going to get that led dimming next!

I messed around with the function but lost patience with it,,. I'll get my lua book out and tackle that one rainy day. Meanwhile, I have been using these delays without any issues (no Vera re-starts) and can probably work on shortening the delay times now that I have my Ethernet gateway working so well!!!

best network performance ever for me since I started with MySensors :)

I keep looking at your scene controller (and the one Henrik did) and I guess I just have to pick one to make!!

[korttoma]

It was all my pleasure Jim, it is nice to have someone to exchange ideas with. I take it you mean the dimming of the backlight right? Let me know if you need some details.

I have also put together a Ethernet GW some time ago but newer got around to take it in to use. And then there was all this about the SPI issue so I guess I need to take it on again at some point. A bit unclear if it will work with the Ethernet board I have anyway.

[BulldogLowell]

@korttoma

yeah, I meant dimming the LED backlight, a nice touch to your project.

your ethernet board uses the same Wiznet chipset, so you may want to try what was posted on the other thread. I got frustrated with my Serial gateway losing its communication with Vera.

[cleight]

Hello, I am building this same thing and have used the sketch and luup code above thanks to @BulldogLowell & @korttoma!

I am having issues though pulling a variable to send to the lcd screen via luup. I put this device under the Light Variable 4 code is at the bottom of the Lua below. This device is another mysensor that is visible in Vera so I am not sure what is wrong, any help someone could provide would be great.

Luup code:

local temp = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 7)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_1", value=temp}, 103)
luup.sleep(750)
local humid = luup.variable_get("urn:micasaverde-com:serviceId:HumiditySensor1","CurrentLevel", 10)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_2", value=humid}, 103)
luup.sleep(750)
local low = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 61)
    luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_3", value=low}, 103)
 luup.sleep(750)
local high = luup.variable_get("urn:upnp-org:serviceId:TemperatureSensor1","CurrentTemperature", 62)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_4", value=high}, 103)
luup.sleep(750)
local conditions = luup.variable_get("urn:upnp-micasaverde-com:serviceId:Weather1","Condition", 6)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;3", variableId="VAR_5", value=conditions}, 103)
luup.sleep(750)  
local conditions = luup.variable_get("urn:upnp-micasaverde-com:serviceId:Weather1","Forecast.1.Condition", 59)
luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;4", variableId="VAR_2", value=conditions}, 103)
 luup.sleep(750)
  local conditions = luup.variable_get("urn:upnp-micasaverde-com:serviceId:TemperatureSensor1","CurrentTemperature", 98)
 luup.call_action("urn:upnp-arduino-cc:serviceId:arduino1", "SendCommand", {radioId="11;4", variableId="VAR_4", value=HTTemp}, 103)
  luup.sleep(750)

Sketch: weather_station.ino