@mfalkvidd Wow, thanks that works!

@mfalkvidd Wow, thanks that works!

@gohan Tried it again
configure now recognizes the rpi:

pi@raspberrypi:~/mys_dev $ ./configure --my-gateway=ethernet --my-port=5003 --my-transport=nrf24 --my-rf24-ce-pin=22 --my-rf24-cs-pin=24
[SECTION] Detecting target machine.
  [OK] machine detected: SoC=BCM2836, Type=rpi2, CPU=armv7l.
[SECTION] Detecting SPI driver.
  [OK] SPI driver detected:BCM.
[SECTION] Detecting init system.
  [OK] init system detected: systemd.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.

But make fails with the following error:

-I./core -I./drivers/Linux -I./drivers/BCM -c drivers/BCM/bcm2835.c -o build/drivers/BCM/bcm2835.o
drivers/BCM/bcm2835.c: In function ‘bcm2835_delayMicroseconds’:
drivers/BCM/bcm2835.c:441:40: error: expected ‘)’ before ‘PRIu64’
   printf("bcm2835_delayMicroseconds %" PRIu64 "\n", micros);
                                        ^
drivers/BCM/bcm2835.c:441:40: warning: spurious trailing ‘%’ in format [-Wformat=]
Makefile:102: recipe for target 'build/drivers/BCM/bcm2835.o' failed
make: *** [build/drivers/BCM/bcm2835.o] Error 1
pi@raspberrypi:~/mys_dev $ 

What to do about it?

@gohan yes. Interesting though when I used git to switch between branches it said all files where the same?
Do you think the fault is in the gateway somehow?

Hello all!

I'm trying to build a gateway with a Raspberry pi2, ethernet and Domoticz.
It looks like the gateway is beeing built ok and seems to run fine but nodes can not communicate with it.
I have read most of the postings here but I can not find any solution.
Hope you guys can help? Please!

I run raspbian (Jessie)
pi@raspberrypi:~/MySensors/bin $ uname -a
Linux raspberrypi 4.9.35-v7+ #1014 SMP Fri Jun 30 14:47:43 BST 2017 armv7l GNU/Linux

Using master branch

https://www.mysensors.org/build/raspberry
git clone https://github.com/mysensors/MySensors.git --branch master

Configuring like this

pi@raspberrypi:~/MySensors $ ./configure --my-gateway=ethernet --my-port=5003 --my-transport=nrf24 --my-rf24-ce-pin=22 --my-rf24-cs-pin=24
[SECTION] Detecting target machine.
  [OK] machine detected: SoC=unknown, Type=unknown, CPU=armv7l.
[SECTION] Checking GPIO Sysfs.
  [OK] /sys/class/gpio/export found
[SECTION] Detecting SPI driver.
  [OK] SPI driver detected:SPIDEV.
[SECTION] Detecting init system.
  [OK] init system detected: systemd.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.

Obs! No Raspberry identification, why not? Maybe that is the culprit?
After make I start the gateway and get this:

pi@raspberrypi:~/MySensors $ cd bin
pi@raspberrypi:~/MySensors/bin $ sudo ./mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: New connection from 127.0.0.1
mysgw: Client 0 connected
mysgw: Client 0: 0;0;3;0;2;
mysgw: Client 0: 0;0;3;0;2;Get Version
mysgw: Client 0: 0;0;3;0;18;PING

Seems nice and dandy and Domoticz connecting fine.
Trying with this example node:

#define MY_RADIO_NRF24
#define MY_RF24_PA_LEVEL RF24_PA_LOW
#define MY_DEBUG
#define MY_NODE_ID 42
//#define MY_DEBUG_VERBOSE_RF24
#define MY_BAUD_RATE 9600

#include <MySensors.h>
#include<Arduino.h>

#define OPEN 1
#define CLOSE 0
#define CHILD_ID 1

MyMessage msg(CHILD_ID, V_TRIPPED);

uint8_t value = OPEN;

void setup()
{
  Serial.print("setup()\n");
}

void presentation()
{
  sendSketchInfo("Door", "2.1.1");
  present(CHILD_ID, S_DOOR);
  Serial.print("presentation()\n");
}

void loop()
{
  value = value == OPEN ? CLOSE : OPEN;
  send(msg.set(value));
  Serial.print("message sent");
  Serial.print(value + "\n");
  sleep(1000);
}

And recieve this when running:

--- Miniterm on /dev/ttyUSB0 9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
40 TSM:INIT
55 TSF:WUR:MS=0
77 TSM:INIT:TSP OK
96 TSM:INIT:STATID=42
120 TSF:SID:OK,ID=42
141 TSM:FPAR
190 TSF:MSG:SEND,42-42-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2267 !TSM:FPAR:NO REPLY
2291 TSM:FPAR
2340 TSF:MSG:SEND,42-42-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:

4417 !TSM:FPAR:NO REPLY
4442 TSM:FPAR
4491 TSF:MSG:SEND,42-42-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6569 !TSM:FPAR:NO REPLY
6594 TSM:FPAR
6643 TSF:MSG:SEND,42-42-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8720 !TSM:FPAR:FAIL
8740 TSM:FAIL:CNT=1
8761 TSM:FAIL:PDT

And no output in gateway either.
Both radio modules using capacitors.

What have I missed?

Thanks, Andreas!