Hello,

I get same message in the serial : 0;0;3;0;9;radio init fail

• IDE 1.6.4 on Yosemit

• MEGA2560

• Ethernet Shield W5100 (like this : https://www.arduino.cc/en/Guide/ArduinoEthernetShield)

• NRF24L01+ (1436AH)

• MySensors Arduino Library v1.5

• I uncommented #define SOFTSPI in MyConfig.h

// Enable SOFTSPI for NRF24L01 when using the W5100 Ethernet module
#define SOFTSPI
#ifdef SOFTSPI
	// Define the soft SPI pins used for NRF radio
	const uint8_t SOFT_SPI_MISO_PIN = 50;
    const uint8_t SOFT_SPI_MOSI_PIN = 51;
    const uint8_t SOFT_SPI_SCK_PIN = 52;
#endif

• EthernetGateway.ino

#define INCLUSION_MODE_TIME 1 // Number of minutes inclusion mode is enabled
#define INCLUSION_MODE_PIN  3 // Digital pin used for inclusion mode button

#define RADIO_CE_PIN        5  // radio chip enable
#define RADIO_SPI_SS_PIN    6  // radio SPI serial select

#define RADIO_ERROR_LED_PIN 7  // Error led pin
#define RADIO_RX_LED_PIN    8  // Receive led pin
#define RADIO_TX_LED_PIN    9  // the PCB, on board LED

// NRFRF24L01 radio driver (set low transmit power by default) 
MyTransportNRF24 transport(RADIO_CE_PIN, RADIO_SPI_SS_PIN, RF24_PA_LEVEL_GW);  

CE & CSN pin are différents configuration in MyConfig.h & EthernetGateway.ino. Can I change this?

Other idea please?

compilation OK !!!

In fact I move in directory /Volumes/Data/Documents/Arduino

• DigitalIO
• list itemMySensors (branch development)
• list itemPinChangeInt

ping OK

but I have fail msg in serial : 0;0;3;0;9;radio init fail

One suggestion please?

@hek said:

Development branch should be working for you.

Branch development is same :disappointed:

MyConfig.h

// Enable SOFTSPI for NRF24L01 when using the W5100 Ethernet module
#define SOFTSPI
#ifdef SOFTSPI
	// Define the soft SPI pins used for NRF radio
	const uint8_t SOFT_SPI_MISO_PIN = 50;
    const uint8_t SOFT_SPI_MOSI_PIN = 51;
    const uint8_t SOFT_SPI_SCK_PIN = 52;
#endif

And I use default example EthernetGateway.ino

Other suggestion please?

@bruno-araripe said:

hy guys,
i have a mega bord, and wiznet ethernet shield, and i want to use this whith ethernet getway. i try many configs, but nothing work. please help me.

Hy,

I have a same project and same problem.

please :sweat:

Hello,

DigitalIO
/Volumes/Data/Documents/Arduino/libraries/Arduino-master/DigitalIO

MySensors
/Volumes/Data/Documents/Arduino/libraries/Arduino-master/MySensors

I don't have utilities directory in MySensors

For information, if I use EthernetGatway exemple in mysensor site : http://www.mysensors.org/build/ethernet_gateway

If I comment "#include <DigitalIO.h>" I have a same problem with other include : MySigningNone.h, MyTransportRFM69.h ...

Only SPI.h is OK

Thanks for your help

Hello,

I'm Mysensors user newbie ;-) and I want create Ethernet Gateway

I use:

• Arduino 1.6.4 on Yosemit
  --> IDE in System/Applications
  --> library are in /Volumes/Data/Documents/Arduino/Arduino-master (or Arduino-development)
• MEGA2560
• Ethernet Shield W5100 (like this : https://www.arduino.cc/en/Guide/ArduinoEthernetShield)
• NRF24L01+ (1436AH)
• MySensors Arduino Library v1.5

Pin configuration:
CE : 10
CSN : 11
MISO : 50
MOSI : 51
SCK : 52

I uncommented #define SOFTSPI in MyConfig.h

But compilation doesn't work. Can you help me please?

EthernetGateway.ino:59:90: fatal error: DigitalIO.h: No such file or directory
compilation terminated.

For information:

• I tryed master and development branch and it's the same
• I tryed without Ethernet Shield W5100, same again

Thank you for your help,

Fabrice.