Navigation

    • Register
    • Login
    • OpenHardware.io
    • Categories
    • Recent
    • Tags
    • Popular
    1. Home
    2. jmmorgan
    • Profile
    • Following
    • Followers
    • Topics
    • Posts
    • Best
    • Groups

    jmmorgan

    @jmmorgan

    0
    Reputation
    22
    Posts
    619
    Profile views
    0
    Followers
    0
    Following
    Joined Last Online

    jmmorgan Follow

    Best posts made by jmmorgan

    This user hasn't posted anything yet.

    Latest posts made by jmmorgan

    • RE: Adding a light switch to Openhab/MQTT gateway

      I had also tried adding the mapping statement, but it had no effect. I have no idea what to try next.? Do you think it could be a problem with the node sketch up?
      Thanks

      posted in OpenHAB
      jmmorgan
      jmmorgan
    • Adding a light switch to Openhab/MQTT gateway

      I am currently running Openhab with Mysensor MQTT gateway and it reads the sensors fine. I have added a light switch to a node and Openhab. When I switch the light on, I see in the Openhab log state "received command on", but nothing shows up in the MQTT output, which I monitor with MQTT-spy. The item line in Openhab is :Switch node2_sw2 "sw2" {mqtt=">[mysensor:MyMQTT/2/5/V_LIGHT:command:ON:1],>[mysensor:MyMQTT/2/5/V_LIGHT:command:OFF:0]"}, where the node is 2 and the child_ID is 5. I do not know what to check next. Any help will be appreciated.
      John

      posted in OpenHAB
      jmmorgan
      jmmorgan
    • Do the Ethernet modules listed in the Store work???

      These modules do not have a SS pin, but rather NSS. Per this topic http://forum.mysensors.org/topic/466/ethernet-gateway-problem/37, these modules may not work. "Checked the board but I see no invertor IC on it so I think NSS is connected to /SCS pin (pin 29). Too bad. I think the shopping list should be updated to a board that has SPI_EN pin (pin 31) connected."

      John

      posted in Troubleshooting
      jmmorgan
      jmmorgan
    • Can't connect to MQTT gateway

      My Sensor:
      I am trying to get the MQTT gateway to work. I have followed the instruction and I can ping the gateway, but I cannot connect. I know this has been discussed and I search the form, but none of the answers work for me. As the labels on the contact of the W5100 differ from what is on mysensor website, I wanted to check to make sure I was connect everything correct (Mysensor documentation-W5100).

      1. GRD=GRD I know this is correct
      2. VCC=V+5 This is supposed to be connected to 3.3 v, but it only works when connect to 5V (I assume that is why change the label to (v+5)
      3. SCK=SOK???
      4. MISO/SO=MI???
      5. MOSI/SI=MO??
      6. SS/CS=NSS???
        Any help would be appreciated.
        Thanks
      posted in Troubleshooting
      jmmorgan
      jmmorgan
    • RE: Pinging Ethernet Wiznet gateway 1.4

      It did change the IP in the new sketch. I finally got it to ping, but I am not quite sure how. Probably too many different version of the gateway in effort to get it to work.
      Thanks

      posted in Troubleshooting
      jmmorgan
      jmmorgan
    • Pinging Ethernet Wiznet gateway 1.4

      I am trying to ping my Ethernet Wiznet gateway version 1.4 from my PC. It says the destination is not found. Hence, my gateway does not work with my Vera. I was using gateway version 1.3 and I was able to ping it without problems. So it is not a hardware issue. The sketch for version 1.3 and 1.4 have the same settings. What am I missing?
      Thanks
      John

      posted in Troubleshooting
      jmmorgan
      jmmorgan
    • RE: Upgrade Ethernet GW -> 1.4 (wiznet)

      I have a similar problem. I upgraded from 1.3 to 1.4 and my Wiznet gateway does not work. I can ping version 1.3 from my PC and it see the gateway. When I ping 1.4 from my PC it says that the destination address can not be found. I have downloaded the latest Ethernet gateway sketch, but it did not help. Has any other file change that could effect this.
      Thanks
      John

      posted in Troubleshooting
      jmmorgan
      jmmorgan
    • RE: VERA 2 Device Install

      Does anyone with a Vera2 have that file?

      posted in Vera
      jmmorgan
      jmmorgan
    • RE: VERA 2 Device Install

      Can anyone tell me what setting they have in the /etc/cmh/serproxy.port file?

      posted in Vera
      jmmorgan
      jmmorgan
    • RE: VERA 2 Device Install

      @wmylionel: Are you using Vera 2? If so what lines do you have in the /etc/cmh/serproxy.port file?
      Thanks
      John

      posted in Vera
      jmmorgan
      jmmorgan