Ok man, where is connection to NFR24l01????
From picture i see you are use SPI but never see where is configure it ?
1st. check are you have a spidev0.0 or another. then config need to be like this:
./configure --spi-spidev-device=/dev/spidev0.0 --my-transport=rf24 --my-rf24-ce-pin=XX --my-rf24-cs-pin=YY
need to change XX and YY with your connection to the Pi.
You use SPI for connection but configure gateway as a serial input.
With this configuration never work. If you make external plate (arduino with NRF24l02) and connect it to serial port of
Pi will work but serial need to be one of real TTys.

Regards

Hi,
I am newbie in My sensors and have problem with BananaPi M1 Soc=A20.
When i try to configure MySensors Gateway always after compilation i receive that:

root@bananapi:/home/pi/install/MySensors# ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-rc.2
mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0-rc.2
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:DIS
mysgw: TSF:TDI:TSL

Compilation always OK without any errors.
Hardware is connected like need to be and connection work on RaspberryPi 2 (same GPIO pinout).
I try with many difference settings in compilation but without sucsses.
With gpio readall i see all GPIOs and can comand it .

root@bananapi:/home/pi/install/MySensors# gpio readall
+----------+-Rev3-+------+--------+------+-------+
| wiringPi | GPIO | Phys | Name   | Mode | Value |
+----------+------+------+--------+------+-------+
|      0   |  17  |  11  | GPIO 0 | OUT  | High  |
|      1   |  18  |  12  | GPIO 1 | IN   | Low   |
|      2   |  27  |  13  | GPIO 2 | ALT4 | Low   |
|      3   |  22  |  15  | GPIO 3 | IN   | Low   |
|      4   |  23  |  16  | GPIO 4 | OUT  | High  |
|      5   |  24  |  18  | GPIO 5 | IN   | Low   |
|      6   |  25  |  22  | GPIO 6 | IN   | Low   |
|      7   |   4  |   7  | GPIO 7 | IN   | Low   |
|      8   |   2  |   3  | SDA    | ALT5 | Low   |
|      9   |   3  |   5  | SCL    | ALT5 | Low   |
|     10   |   8  |  24  | CE0    | IN   | Low   |
|     11   |   7  |  26  | CE1    | ALT5 | Low   |
|     12   |  10  |  19  | MOSI   | IN   | Low   |
|     13   |   9  |  21  | MISO   | IN   | Low   |
|     14   |  11  |  23  | SCLK   | ALT5 | Low   |
|     15   |  14  |   8  | TxD    | OUT  | High  |
|     16   |  15  |  10  | RxD    | OUT  | High  |
|     17   |  28  |   3  | GPIO 8 | ALT0 | Low   |
|     18   |  29  |   4  | GPIO 9 | IN   | Low   |
|     19   |  30  |   5  | GPIO10 | IN   | Low   |
|     20   |  31  |   6  | GPIO11 | ALT4 | Low   |
+----------+------+------+--------+------+-------+

This is some of my configures:

 ./configure --spi-spidev-device=/dev/spidev0.0 --my-transport=nrf24 --my-rf24-ce-pin=8 --my-rf24-cs-pin=25 --my-gateway=ethernet --my-port=5003

./configure --spi-spidev-device=/dev/spidev0.0 --my-transport=nrf24 --my-rf24-ce-pin=24 --my-rf24-cs-pin=22 --my-gateway=ethernet --my-port=5003

./configure --spi-spidev-device=/dev/spidev0.0 --my-transport=nrf24 --my-rf24-ce-pin=10--my-rf24-cs-pin=6 --my-gateway=ethernet --my-port=5003

This is my answer on list devices

root@bananapi:/home/pi/install/MySensors# ls /dev/spi*
/dev/spidev0.0  /dev/spidev0.1

Everything need to be ok but is not :( .
Because thi is not a my 1st project i know all work on RaspberryPi 2 and Orange Pi PC - Soc=H3.
I have a problem with Soc= A20.

Please help

Kind Regards