The kickstarter project Airboard
A "Shield" with RF24 and most of the node is done?
What did you think about it?

ATmega328P processor @ 8MHz
Peripherals and I/Os
16-million colors user-defined RGB LED, 2240mcd max, 120° viewing angle
7x GPIO, 3x PWM, 2x 10-bit ADC, I2C, SPI solderless proto connector
Up to 18x GPIOs, 6x 10-bit analog inputs or 6x PWMs

Power Management System
Autonomy in communication: 6 months @ 1 data/minute
Autonomy in sleep mode: up to 3 years
Charge time: 40-60 minutes
150mAh rechargeable lithium-ion battery
Built-in lithium-ion battery charger
Charging via micro USB from computer system or power adapter
Battery protection circuitry (Over Current, Over Charge, Over Discharge)
USB voltage, charge status and battery level indicators
5VUSB/500mA and 3.3V/200mA regulated power outputs for prototyping board
3.3V/1A switchable regulated power output for wireless shield

Hi, I 'm stating with Jeedom, installed on a Synology DS313J.
After installaing jeedom, and installed the Mysensors plugin, I try to configure my serial gateway, attached with a USB / serial on the NAS.
I ve installed some USB./Serial drivers and it seems that the Virtual Serial port mounted is USB_SERIAL for me (checked with " ls /dev" on Nas SSH console.
So when I configure the Serial port to be .dev/USB_SERIAL, save it I always have a message that NODEJS is not running...
Did you have any idea?
On the diskstation software, I can see that NODEJS is running... Maybe a problem of the acces? On the wiki we can see that NODEJS is not needed now?
Please help me.
BR.

I have seen the same issue with 1.4 when using DHT or Dallas ...
I have try to clean EEPROM, change on Vera from metric to Imperial and back to metric without any succes...
So hardcode temperature in C was the solution for me...

Hi,
I'm trying to make exactly the same thing with another reader, RC-522.
I was using Mysensor 1.3 and that works for most things but without possibillity to change status from my Vera.
So I decided to turn on 1.4.
I've update my gateway, change the Vera files, delete all nodes and sensors related to Mysensors in Vera. (just keep the MySensorGW Module.

And rewrite MyRFID code...

The problem is this reader is only SPI... But I'm not sure this is here my problem...

The code I'm using now:
MYRFID.ino

So the first problem is when using 1.4, I have make a test with DHT source code, launch node searching... This find 2 modules: One for temp and one for humidity... Those modules are working... I'm just surprized not to see the module "Arduino Node"...

I ve tested with my code and launch node searching, this have just created me the Arduino Node Module and not the Lock module...

When I check the serial debug information on my node I can see:

Setup is starting Up
sensor started, id 1
send: 1-1-0-0 s=255,c=0,t=17,pt=0,l=15,st=ok:1.4b1 (18848a2)
send: 1-1-0-0 s=255,c=3,t=6,pt=1,l=1,st=fail:0
send: 1-1-0-0 s=255,c=3,t=11,pt=0,l=11,st=fail:MYRFID Lock
send: 1-1-0-0 s=255,c=3,t=12,pt=0,l=3,st=fail:1.0
send: 1-1-0-0 s=1,c=0,t=19,pt=0,l=15,st=fail:1.4b1 (18848a2)
Close lock
send: 1-1-0-0 s=1,c=1,t=36,pt=2,l=2,st=fail:0
RF24 initialized and GW contacted
RFID Reader initialized
 
------- SETUP IS DONE --------
 
Cardnumber Read : 151612433071
Open lock
send: 1-1-0-0 s=1,c=1,t=36,pt=2,l=2,st=fail:1
Close lock
send: 1-1-0-0 s=1,c=1,t=36,pt=2,l=2,st=fail:0
send: 1-1-255-255 s=255,c=3,t=7,pt=0,l=0,st=fail:
Open lock
send: 1-1-0-0 s=1,c=1,t=36,pt=2,l=2,st=fail:1
Close lock
send: 1-1-0-0 s=1,c=1,t=36,pt=2,l=2,st=fail:0
Open lock
send: 1-1-0-0 s=1,c=1,t=36,pt=2,l=2,st=fail:1
Close lock
send: 1-1-0-0 s=1,c=1,t=36,pt=2,l=2,st=fail:0
Open lock
send: 1-1-0-0 s=1,c=1,t=36,pt=2,l=2,st=fail:1
Close lock
send: 1-1-0-0 s=1,c=1,t=36,pt=2,l=2,st=fail:0
send: 1-1-255-255 s=255,c=3,t=7,pt=0,l=0,st=fail:
Open lock
send: 1-1-0-0 s=1,c=1,t=36,pt=2,l=2,st=fail:1
Close lock
send: 1-1-0-0 s=1,c=1,t=36,pt=2,l=2,st=fail:0
Open lock

So As I understand, as the Sensor node could not receive the ack from the GW, it change back the status of the lock...

Did you have any recommandation? Idea?

Thank you.

Hi,
I think the Value is the pressure in Pa...
Maybe you can divide it by 100 to turn it in Hpa to let it working with Vera...
You can see the comment on the bottom of the page..
http://www.mysensors.org/build/pressure
BR.

Hi, Thank you for your ideas.
I'm not sure but as I have understand your script, in fact, the script is client and ask to the Mysensor gateway the values which have been send back to the domoticz script and sent to pachube.

So: perl script => MysensorGW => perl script => Pachube
the refrech rate is done by the perl script

The problem of this, if i'm not wrong is to have a high speed in case you would like to see a door opening and manage alarm system for example. The problem is also for me to be able to receive action from external system to send relay action for exemple => so need gateway to be both server and client...

On the same way, i dont understand how and where are stored the values inside the gateway if not used on each reception, are they stored somewhere to be able to answer them when serial request arrive?
BR.

Hello,

I have started Home automation one year ago and I'm really interested on this project.
As soon as understood, the gateway are always "server" gateway and are not sending data automatically like a "client" can send information on each reception.

My idea is to be able to use gateway to send informations from sensors to a storage place in order to be able to make charts and generate actions.

My first idea is to use the ethernet gateway and make sketch to make a html request to a php server with Post argument as var to be integrated inside a database. like this project: http://www.instructables.com/id/Save-data-of-temperature-and-humidity-on-MySQL-wit/
I already have make this kind of plateform with lots of sensors on same arduino but the idea to be able to place sensors everywhere with RF transmition is really a good view, missing at home for me!

The second idea is to make pachube request to store datas. using this kind of sketch => http://arduino.cc/en/Tutorial/PachubeCient )

I don't know if someone have think about a similar idea?
What are your opinion about this? Some recommendation?

Thank you.