Hi,

The strange behavior is no longer present and I can't replicate the problem. I suspect there was a general communication problem with the gateway.
Anyway, please see the following debug prints.

 
 __  __       ____
|  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
| |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
| |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
|_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
        |___/                      2.3.2

16 MCO:BGN:INIT NODE,CP=RNNNA-Q-,FQ=16,REL=255,VER=2.3.2
26 TSM:INIT
28 TSF:WUR:MS=0
34 TSM:INIT:TSP OK
36 TSF:SID:OK,ID=1
38 TSM:FPAR
41 ?TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
247 TSF:MSG:READ,0-0-1,s=255,c=3,t=8,pt=1,l=1,sg=0:0
252 TSF:MSG:FPAR OK,ID=0,D=1
2050 TSM:FPAR:OK
2051 TSM:ID
2052 TSM:ID:OK
2054 TSM:UPL
2057 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2068 TSF:MSG:READ,0-0-1,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2073 TSF:MSG:PONG RECV,HP=1
2075 TSM:UPL:OK
2077 TSM:READY:ID=1,PAR=0,DIS=1
2081 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2100 TSF:MSG:READ,0-0-1,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2110 TSF:MSG:SEND,1-1-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.3.2
2118 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2179 TSF:MSG:READ,0-0-1,s=255,c=3,t=6,pt=0,l=1,sg=0:M
2186 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=11,pt=0,l=18,sg=0,ft=0,st=OK:Stairs Wall Lights
2198 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.2
2209 TSF:MSG:SEND,1-1-0-0,s=0,c=0,t=4,pt=0,l=10,sg=0,ft=0,st=OK:Top_Lights
2318 TSF:MSG:SEND,1-1-0-0,s=1,c=0,t=4,pt=0,l=13,sg=0,ft=0,st=OK:Bottom_Lights
2427 TSF:MSG:SEND,1-1-0-0,s=2,c=0,t=3,pt=0,l=17,sg=0,ft=0,st=OK:Top_Lights_Switch
2537 TSF:MSG:SEND,1-1-0-0,s=3,c=0,t=3,pt=0,l=20,sg=0,ft=0,st=OK:Bottom_Lights_Switch
2648 TSF:MSG:SEND,1-1-0-0,s=4,c=0,t=23,pt=0,l=23,sg=0,ft=0,st=OK:Top_Lights_Switch_Level
2758 TSF:MSG:SEND,1-1-0-0,s=5,c=0,t=23,pt=0,l=25,sg=0,ft=0,st=OK:Bottom_Lights_Switch_Leve
2866 MCO:REG:REQ
2871 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
2877 TSF:MSG:READ,0-0-1,s=255,c=3,t=27,pt=1,l=1,sg=0:1
2882 MCO:PIM:NODE REG=1
2884 MCO:BGN:STP
Setup Started.
2888 TSF:MSG:SEND,1-1-0-0,s=2,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
2995 TSF:MSG:SEND,1-1-0-0,s=3,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
Top Switch level: 100
3103 TSF:MSG:SEND,1-1-0-0,s=4,c=1,t=24,pt=1,l=1,sg=0,ft=0,st=OK:100
Bottom Switch level: 100
3211 TSF:MSG:SEND,1-1-0-0,s=5,c=1,t=24,pt=1,l=1,sg=0,ft=0,st=OK:100
3318 TSF:MSG:SEND,1-1-0-0,s=0,c=2,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
3364 TSF:MSG:READ,0-0-1,s=0,c=1,t=3,pt=0,l=1,sg=0:0
V_Dimmer received: 0
Fade to Level: 0:0-->0
3425 TSF:MSG:SEND,1-1-0-0,s=1,c=2,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
3469 TSF:MSG:READ,0-0-1,s=1,c=1,t=3,pt=0,l=1,sg=0:0
V_Dimmer received: 1
Fade to Level: 1:0-->0
Setup Colplete.
3531 MCO:BGN:INIT OK,TSP=1
Switch 1 pressed.
11350 TSF:MSG:SEND,1-1-0-0,s=2,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:1
Fade to Level: 0:0-->100
Sensor Update received: 0
12360 TSF:MSG:SEND,1-1-0-0,s=0,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:1
12466 TSF:MSG:SEND,1-1-0-0,s=0,c=1,t=3,pt=1,l=1,sg=0,ft=0,st=OK:100
Switch 1 pressed.
14713 TSF:MSG:SEND,1-1-0-0,s=2,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
Fade to Level: 0:100-->0
Sensor Update received: 0
15726 TSF:MSG:SEND,1-1-0-0,s=0,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
15832 TSF:MSG:SEND,1-1-0-0,s=0,c=1,t=3,pt=1,l=1,sg=0,ft=0,st=OK:0

Thanks

Hi mfalkvidd,

Thank you for the prompt response.

The code is the following:

//#define MY_DEBUG   

#define MY_RADIO_NRF24
#define MY_RX_MESSAGE_BUFFER_FEATURE
#define MY_RF24_IRQ_PIN 2
#include <MySensors.h>
#include <Bounce2.h>
#include <elapsedMillis.h>

#define SN "Stairs Wall Lights"
#define SV "1.2"

#define TopLED_ID 0
#define BottomLED_ID 1
#define TopSwitch_ID 2
#define BottomSwitch_ID 3
#define TopSwitchLev_ID 4
#define BotSwitchLev_ID 5

#define TopLED_PIN 3   
#define BottomLED_PIN 5
#define TopSwitch_PIN A3  // External switch 1
#define BottomSwitch_PIN A4  // External switch 2
#define FADE_DELAY 10  // Delay in ms for each percentage fade up/down (10ms = 1s full-range dim)
#define Light_On 100
#define Light_Off 0
#define HEARTBEAT_TIME 605000 // 10 minutes
#define HEARTBEAT_NO_RETURN 3

uint8_t CurrentLevel[2];  // Current dim level...
bool LastState[2];
byte updateSensor;

MyMessage TopDimmerMsg(TopLED_ID, V_DIMMER);
MyMessage TopLightMsg(TopLED_ID, V_LIGHT);
MyMessage BotDimmerMsg(BottomLED_ID, V_DIMMER);
MyMessage BotLightMsg(BottomLED_ID, V_LIGHT);
MyMessage TopSwitchMsg(TopSwitch_ID, V_STATUS);
MyMessage BotSwitchMsg(BottomSwitch_ID, V_STATUS);
MyMessage TopSwitchLevMsg(TopSwitchLev_ID, V_VAR1);
MyMessage BotSwitchLevMsg(BotSwitchLev_ID, V_VAR1);

elapsedMillis heartBeatTimer; 
byte heartBeatReturn;
Bounce debouncer1 = Bounce(); 
Bounce debouncer2 = Bounce();

void(* resetFunc) (void) = 0; //declare reset function @ address 0

void setup()
{
#ifdef MY_DEBUG
  Serial.begin(115200);
  Serial.println("Setup Started.");
#endif  
  pinMode(TopSwitch_PIN, INPUT_PULLUP);
  pinMode(BottomSwitch_PIN, INPUT_PULLUP);
  LastState[TopLED_ID] = digitalRead(TopSwitch_PIN);
  LastState[BottomLED_ID] =  digitalRead(BottomSwitch_PIN);
  // switch off lights
  analogWrite(TopLED_PIN, 0); CurrentLevel[TopLED_ID] = 0; 
  analogWrite(BottomLED_PIN, 0); CurrentLevel[BottomLED_ID] = 0;

  send(TopSwitchMsg.set(LastState[TopLED_ID])); wait(100);
  send(BotSwitchMsg.set(LastState[BottomLED_ID])); wait(100);
  byte b = loadState(TopSwitchLev_ID);
#ifdef MY_DEBUG
  Serial.print("Top Switch level: ");
  Serial.println(b);
#endif  
  if (b == Light_Off) {b = Light_On; saveState(TopSwitchLev_ID, Light_On);}
  send(TopSwitchLevMsg.set(b)); wait(100);
  b = loadState(BotSwitchLev_ID);
#ifdef MY_DEBUG
  Serial.print("Bottom Switch level: ");
  Serial.println(b);
#endif  
  if (b == Light_Off) {b = Light_On; saveState(BotSwitchLev_ID, b);}
  send(BotSwitchLevMsg.set(b)); wait(100);

  debouncer1.attach(TopSwitch_PIN);
  debouncer1.interval(5);
  debouncer2.attach(BottomSwitch_PIN);
  debouncer2.interval(5);
  heartBeatTimer = 0;
  heartBeatReturn = 0;
  updateSensor = 255;
  request(TopLED_ID, V_DIMMER); wait(100);
  request(BottomLED_ID, V_DIMMER); wait(100);
#ifdef MY_DEBUG
  Serial.println("Setup Colplete.");
#endif  
}

void presentation()
{
  sendSketchInfo(SN, SV);
  present(TopLED_ID, S_DIMMER, "Top_Lights"); wait(100);
  present(BottomLED_ID, S_DIMMER, "Bottom_Lights"); wait(100);
  present(TopSwitch_ID, S_BINARY, "Top_Lights_Switch");  wait(100);
  present(BottomSwitch_ID, S_BINARY, "Bottom_Lights_Switch");  wait(100);
  present(TopSwitchLev_ID, S_CUSTOM, "Top_Lights_Switch_Level");  wait(100);
  present(BotSwitchLev_ID, S_CUSTOM, "Bottom_Lights_Switch_Level");  wait(100);
}

void loop()
{
  debouncer1.update();
  bool CurrentState = debouncer1.read();
  if (CurrentState != LastState[TopLED_ID]) {
    #ifdef MY_DEBUG
      Serial.println("Switch 1 pressed.");
    #endif  
    send(TopSwitchMsg.set(CurrentState));
    LastState[TopLED_ID] = CurrentState;
    if (CurrentLevel[TopLED_ID] > Light_Off) {
      fadeToLevel(Light_Off, TopLED_ID);
    }
    else {
      byte b = loadState(TopSwitchLev_ID);  
      fadeToLevel(b, TopLED_ID);
    }
  }
  debouncer2.update();
  CurrentState = debouncer2.read();
  if (CurrentState != LastState[BottomLED_ID]) {
    #ifdef MY_DEBUG
      Serial.println("Switch 2 pressed.");
    #endif  
    send(BotSwitchMsg.set(CurrentState));
    LastState[BottomLED_ID] = CurrentState; 
    if (CurrentLevel[BottomLED_ID] > 0) {
      fadeToLevel(Light_Off, BottomLED_ID);
    }
    else {
      byte b = loadState(BotSwitchLev_ID);  
      fadeToLevel(b, BottomLED_ID);
    }
  }
  if (heartBeatTimer > HEARTBEAT_TIME) {
    heartBeatTimer = 0;
    if (!sendHeartbeat()) {
        #ifdef MY_DEBUG
          Serial.println("Hearbeat echo NOT received.");
        #endif  
      heartBeatReturn++;
      if (heartBeatReturn == HEARTBEAT_NO_RETURN) resetFunc();
    } else {
        #ifdef MY_DEBUG
          Serial.println("Hearbeat echo received.");
        #endif  
        heartBeatReturn = 0;
        request(TopLED_ID, V_DIMMER); wait(200);
        request(BottomLED_ID, V_DIMMER); wait(200);
    }
  }
  if (updateSensor != 255) {
    #ifdef MY_DEBUG
      Serial.print("Sensor Update received: ");
      Serial.println(updateSensor);
    #endif  
    if (updateSensor == TopLED_ID) {
      send(TopLightMsg.set(CurrentLevel[updateSensor] > 0));wait(100);
      send(TopDimmerMsg.set(CurrentLevel[updateSensor])); 
    }
    else if (updateSensor == BottomLED_ID){
      send(BotLightMsg.set(CurrentLevel[updateSensor] > 0));wait(100);
      send(BotDimmerMsg.set(CurrentLevel[updateSensor]));       
    }
    updateSensor = 255;
  }
}

void receive(const MyMessage &message)
{
	if (message.type == V_LIGHT) {
    bool requestedLevel = message.getBool();
    #ifdef MY_DEBUG
      Serial.print("V_Light received: ");
      Serial.println(message.sensor);
    #endif  
    int lvl;
    if (requestedLevel == LOW) lvl = Light_Off; else lvl = Light_On;
		fadeToLevel(lvl, message.sensor);
	 }
  else if (message.type == V_DIMMER) {
    #ifdef MY_DEBUG
      Serial.print("V_Dimmer received: ");
      Serial.println(message.sensor);
    #endif  
    int requestedLevel = message.getInt();
    fadeToLevel(requestedLevel, message.sensor);
  }
  else if (message.type == V_VAR1) {
    #ifdef MY_DEBUG
      Serial.print("V_VAR1 received: ");
      Serial.println(message.sensor);
    #endif  
    byte b = message.getByte();
    if (b > Light_On) b = Light_On;
    if (message.sensor == TopSwitchLev_ID) {
      saveState(TopSwitchLev_ID, b);
    }
    else if (message.sensor == BotSwitchLev_ID) {
      saveState(BotSwitchLev_ID, b);
    }
  }
}

void fadeToLevel(int toLevel, byte SensorID)
{
  #ifdef MY_DEBUG
    Serial.print("Fade to Level: ");
    Serial.print(SensorID);
    Serial.print(":");
    Serial.print(CurrentLevel[SensorID]);
    Serial.print("-->");
    Serial.println(toLevel);
  #endif  
  byte SensorPIN; 
  if (SensorID == TopLED_ID) SensorPIN = TopLED_PIN; 
  else if (SensorID == BottomLED_ID) SensorPIN = BottomLED_PIN;
  int delta = (toLevel - CurrentLevel[SensorID]) < 0 ? -1 : 1;
  if (CurrentLevel[SensorID] != toLevel) {
    updateSensor = SensorID;
    while (CurrentLevel[SensorID] != toLevel) {
      CurrentLevel[SensorID] += delta;
      analogWrite(SensorPIN, (int)(CurrentLevel[SensorID] / 100. * 255));
//      delay(FADE_DELAY);
      wait(FADE_DELAY);
    }
  }
}

There is no send() inside receive().

Any ideas?

Hi all,

I've got the same message when call wait(xx);

while (CurrentLevel[SensorID] != toLevel) {
	CurrentLevel[SensorID] += delta;
	analogWrite(SensorPIN, (int)(CurrentLevel[SensorID] / 100. * 255));
//    delay(FADE_DELAY);
	wait(FADE_DELAY);

23902 TSF:MSG:READ,0-0-1,s=0,c=1,t=3,pt=0,l=1,sg=0:5
23907 !MCO:PRO:RC=1
23909 !MCO:PRO:RC=1
23911 !MCO:PRO:RC=1
23913 !MCO:PRO:RC=1
23915 !MCO:PRO:RC=1
23916 !MCO:PRO:RC=1
23918 !MCO:PRO:RC=1
23920 !MCO:PRO:RC=1
23922 !MCO:PRO:RC=1
23924 !MCO:PRO:RC=1
23926 !MCO:PRO:RC=1
23928 !MCO:PRO:RC=1
23930 !MCO:PRO:RC=1
23931 !MCO:PRO:RC=1
23933 !MCO:PRO:RC=1
23936 !MCO:PRO:RC=1
23938 !MCO:PRO:RC=1
23940 !MCO:PRO:RC=1
23942 !MCO:PRO:RC=1
23944 !MCO:PRO:RC=1
23946 !MCO:PRO:RC=1
23948 !MCO:PRO:RC=1
23949 !MCO:PRO:RC=1
23951 !MCO:PRO:RC=1
23953 !MCO:PRO:RC=1
23955 !MCO:PRO:RC=1
23957 !MCO:PRO:RC=1

When I replace wait with delay the message doesn't appear.

Why is that?

Regards,
Radi