Thanks for the feedback. I have several graphs in my XTension Webremote that are showing my temperatures as a seesaw between whole degrees. Accuracy is fine, the half degree C is more than close enough, I just want the graphs to be smoother.
Posts made by robertober
RE: How to force DS18B20s to use 12 bit outputs.
How to force DS18B20s to use 12 bit outputs.
I have a string of 6 DS18x20s on an arduino reader. The output from the Arduino is reporting all sensors with 9 bit resolution. How can I force it to the full 12 bit resolution on the DS18B20s? If one of the sensors is a 9 bit DS18S20, will that force the reader to convert all the other sensors at the same resolution?
RE: Soft WDT reset on ESP8266
@robertober I think that my issue is one of two things, one of the pins not properly connected, or a problem in the software. I started out using the sketch that is in the mySensor library, but found that the file ESP8266wifi.h was missing. I downloaded a file named https://github.com/ekstrand/ESP8266wifi/archive/master.zip and installed it into my library. I also noticed that the instructions built into the ESP8244Gateway Skecth gives two different connections for GPIO15. Is the pulldown resistor needed to run or only for uploading?
My controller (XTension running on a Mac Mini) seems to be receiving a different port request each time the 8266 resets. Anyone know why?
The log in Tension shows the following:
1/5/16 1:57:39 PM mySensor WiFi: IP Open to 10.0.1.149:63444 failed.
1/5/16 1:57:41 PM Interface mySensor WiFi has been unexpectedly disconnected from XTension.
1/5/16 1:57:41 PM Interface "mySensor WiFi" has quit: (with no message) code: 0
1/5/16 1:57:46 PM Retry connection to interface "mySensor WiFi". Tries left: 9
1/5/16 1:57:46 PM Helper Command: (/XTension/XTension.app/Contents/Pitchers/mysensors.isf/mysensors.isf IP 127.0.0.1 52301 340 10.0.1.149 57580)
1/5/16 1:57:46 PM Starting Interface "mySensor WiFi"
1/5/16 1:57:56 PM mySensor WiFi: IP Open to 10.0.1.149:63449 failed.
1/5/16 1:57:58 PM Received Temperature for TEMPERATURE ATTIC of 38.7F (RFX)
1/5/16 1:57:59 PM Interface mySensor WiFi has been unexpectedly disconnected from XTension.
1/5/16 1:57:59 PM Interface "mySensor WiFi" has quit: (with no message) code: 0
1/5/16 1:58:04 PM Retry connection to interface "mySensor WiFi". Tries left: 9
1/5/16 1:58:04 PM Helper Command: (/XTension/XTension.app/Contents/Pitchers/mysensors.isf/mysensors.isf IP 127.0.0.1 52301 341 10.0.1.149 57580)
1/5/16 1:58:04 PM Starting Interface "mySensor WiFi"
Soft WDT reset on ESP8266
I've built my own WiFi Gateway using an ESP-07. The sketch loaded without error, but the program won't run. I put in my network and port data. all else is on default settings. All my sensors are currently reporting(successfully) to a SerialGateway. Both controllers are set up to report through an interface to my XTension HA program. The Serial Gateway works fine, the 8266 gateway connects to XTension, but then reboots, disconnects and reconnects about every 7 seconds or so. Can anyone point me towards probable corrections?
I get the following output to the serial monitor:
ESP8266 MySensors Gateway
Connecting to Oberhaus
Soft WDT reset
sp: 3ffefe10 end: 3fff0030 offset: 01b0
3ffeffc0: 00000000 00000001 3ffeee00 402034fc
3ffeffd0: 00000000 402020cc 00000001 40205308
3ffeffe0: 9501000a 00ffffff 0101000a 3ffef004
3ffefff0: 3ffe84a9 3ffeeef4 3fff0080 4020251b
3fff0000: 3ffe8860 9501000a 00000000 00000000
3fff0010: 3fffdc20 00000000 3ffeeffc 402052d2
3fff0020: 00000000 00000000 3ffef010 40100114
ets Jan 8 2013,rst cause:2, boot mode:(3,6)
load 0x4010f000, len 1264, room 16
Following is my pinouts and connections to the 8266.
ESP8266 Module Esp-07 AP+STA WC
Rest 10K to VCC/Switch to Ground
CH_PD 10K to VCC
GPIO0 10K to VCC/Switch to Ground
GPIO2 10K to VCC