hello .
I have problem with switch command.i am using this sketch:
/**
* The MySensors Arduino library handles the wireless radio link and protocol
* between your home built sensors/actuators and HA controller of choice.
* The sensors forms a self healing radio network with optional repeaters. Each
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
* network topology allowing messages to be routed to nodes.
*
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
* Copyright (C) 2013-2015 Sensnology AB
* Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
*
* Documentation: http://www.mysensors.org
* Support Forum: http://forum.mysensors.org
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
*******************************
*
* REVISION HISTORY
* Version 1.0 - Henrik Ekblad
*
* DESCRIPTION
* Example sketch for a "light switch" where you can control light or something
* else from both HA controller and a local physical button
* (connected between digital pin 3 and GND).
* This node also works as a repeader for other nodes
* http://www.mysensors.org/build/relay
*/
// Enable debug prints to serial monitor
#define MY_DEBUG
// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
// Enabled repeater feature for this node
#define MY_REPEATER_FEATURE
#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>
#define RELAY_PIN1 6 // Arduino Digital I/O pin number for relay
#define BUTTON_PIN1 3 // Arduino Digital I/O pin number for button
#define CHILD_ID1 1 // Id of the sensor child
#define RELAY_PIN2 7 // Arduino Digital I/O pin number for relay
#define BUTTON_PIN2 4 // Arduino Digital I/O pin number for button
#define CHILD_ID2 2 // Id of the sensor child
#define RELAY_PIN3 8 // Arduino Digital I/O pin number for relay
#define BUTTON_PIN3 5 // Arduino Digital I/O pin number for button
#define CHILD_ID3 3 // Id of the sensor child
#define RELAY_ON 1
#define RELAY_OFF 0
Bounce debouncer1 = Bounce();
int oldValue1 = 0;
bool state1;
Bounce debouncer2 = Bounce();
int oldValue2 = 0;
bool state2;
Bounce debouncer3 = Bounce();
int oldValue3 = 0;
bool state3;
MyMessage msg1(CHILD_ID1, V_LIGHT);
MyMessage msg2(CHILD_ID2, V_LIGHT);
MyMessage msg3(CHILD_ID3, V_LIGHT);
void setup()
{
// Setup the button
pinMode(BUTTON_PIN1, INPUT);
digitalWrite(BUTTON_PIN1, HIGH);
pinMode(BUTTON_PIN2, INPUT);
digitalWrite(BUTTON_PIN2, HIGH);
pinMode(BUTTON_PIN3, INPUT);
digitalWrite(BUTTON_PIN3, HIGH);
// After setting up the button, setup debouncer
debouncer1.attach(BUTTON_PIN1);
debouncer1.interval(5);
debouncer2.attach(BUTTON_PIN2);
debouncer2.interval(5);
debouncer3.attach(BUTTON_PIN3);
debouncer3.interval(5);
// Make sure relays are off when starting up
digitalWrite(RELAY_PIN1, RELAY_OFF);
pinMode(RELAY_PIN1, OUTPUT);
digitalWrite(RELAY_PIN2, RELAY_OFF);
pinMode(RELAY_PIN2, OUTPUT);
digitalWrite(RELAY_PIN3, RELAY_OFF);
pinMode(RELAY_PIN3, OUTPUT);
// Set relay to last known state (using eeprom storage)
state1 = loadState(CHILD_ID1);
digitalWrite(RELAY_PIN1, state1 ? RELAY_ON : RELAY_OFF);
state2 = loadState(CHILD_ID2);
digitalWrite(RELAY_PIN2, state2 ? RELAY_ON : RELAY_OFF);
state3 = loadState(CHILD_ID3);
digitalWrite(RELAY_PIN3, state3 ? RELAY_ON : RELAY_OFF);
}
void presentation() {
// Send the sketch version information to the gateway and Controller
sendSketchInfo("Relay & Button", "1.0");
// Register all sensors to gw (they will be created as child devices)
present(CHILD_ID1, S_LIGHT);
present(CHILD_ID2, S_LIGHT);
present(CHILD_ID3, S_LIGHT);
}
/*
* Example on how to asynchronously check for new messages from gw
*/
void loop()
{
{ debouncer1.update();
// Get the update value
int value1 = debouncer1.read();
if (value1 != oldValue1 && value1 == 0) {
send(msg1.set(state1 ? false : true), true); // Send new state and request ack back
}
oldValue1 = value1;
}
{ debouncer2.update();
// Get the update value
int value2 = debouncer2.read();
if (value2 != oldValue2 && value2 == 0) {
send(msg2.set(state2 ? false : true), true); // Send new state and request ack back
}
oldValue2 = value2;
}
{ debouncer3.update();
// Get the update value
int value3 = debouncer3.read();
if (value3 != oldValue3 && value3 == 0) {
send(msg3.set(state3 ? false : true), true); // Send new state and request ack back
}
oldValue3 = value3;
}
}
void receive(const MyMessage &message) {
// We only expect one type of message from controller. But we better check anyway.
if (message.isAck()) {
Serial.println("This is an ack from gateway");
}
if (message.type == V_LIGHT) {
switch (message.sensor) {
case 1:
state1 = message.getBool();
digitalWrite(message.sensor + 2, state1 ? RELAY_ON : RELAY_OFF);
break;
case 2:
state2 = message.getBool();
digitalWrite(message.sensor + 2, state2 ? RELAY_ON : RELAY_OFF);
break;
case 3:
state3 = message.getBool();
digitalWrite(message.sensor + 2, state3 ? RELAY_ON : RELAY_OFF);
break;
}
// Write some debug info
Serial.print("Incoming change for sensor:");
Serial.print(message.sensor);
Serial.print(", New status: ");
Serial.println(message.getBool());
}
}
this is a 3 channel relay with button.
some time commands sent and some time could not be sent and show "Error sending switch command, check device/hardware !" I did take steps in accordance site and use a 4.7uf capacitor between vcc and gnd in radio . now some time command sent . some time could not be sent and i wait for a time (1 min , 2 min and more) and again send command and this is ok ! also when for test i sent some consecutive command (on/off/on/off/on) so again i see "Error sending switch command, check device/hardware !" i wait again and after a while work again and ok !
I did search between topics and i see some suggest to use this module:
link text
so i use this but the problem did not solve for me .
also i use a repeater between node and gateway but...
Does anyone a proposal for my problem ?
Best Regards S_m .
