Ok, so as temperature/humidity sensor it works ok :)

But I can't get it to work as relay node.
Rx led is blinking when I push the button but nothing else is happening (no affection @ relay).

repeater started, id 0
send: 0-0-0-0 s=255,c=0,t=18,pt=0,l=5,st=fail:1.4.1
send: 0-0-0-0 s=255,c=3,t=6,pt=1,l=1,st=fail:0
send: 0-0-0-0 s=255,c=3,t=11,pt=0,l=14,st=fail:Relay & Button
send: 0-0-0-0 s=255,c=3,t=12,pt=0,l=3,st=fail:1.0
send: 0-0-0-0 s=1,c=0,t=3,pt=0,l=5,st=fail:1.4.1
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,st=fail:
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,st=fail:
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-0-0 s=1,c=1,t=2,pt=2,l=2,st=fail:0
send: 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,st=fail:```

Wow :) TimO thx a lot !!! it's alive :+1: I've connected humidity and temp sensor for testing,

What exactly should i change?

shouldn't I change sth in RF24_config.h ?

nothing has changed

Hi guys :)

First of all, I thank u very much for such a briliant site !
I do at home overhaul, so I decided a few things to automate. I have Mysensors serial gw (Arduino Uno) connected to Raspbery Pi with Domoticz on it. With simple sketches it works like a charm (with Arduino Nano nodes). But not with my Arduino Mega :(

I'd like to make arduino mega node which will be connected to 16 channel (or more) relay board witch will controll lights all over my house. The perfect sketch for it is RelayWithButtonActuator (so I could control it both from standard buttons and Domoticz). And it works perfect with arduino nano board (I've tried unmodyfied sketch). I' cant even start with Mega because all I can get from it's serial port is "check wires" message...

I know that Mega has diferent pinout then nano/uno/pro... but i've connected it like below

pin D8-----------CE (chip enable in)
SS pin D53----------CSN (chip select in)
SCK pin D52----------SCK (SPI clock in)
MOSI pin D51----------SDI (SPI Data in)
MISO pin D50----------SDO (SPI data out)

But what with IRQ pin ? And should I change sth . in sketch file? I'm just getting started with all that Arduino stuff so thank u in advance for guiding me :) And sry for my English.