Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Ikea utrusta ansluta

Zachini last edited by

Does anyone have an ikea ansluta/utrusta remote controll to sell? The controll is no longer in production and I really need one.
Reply Quote 0
1 Reply Last reply
leonard last edited by

In mine the switch broke, so I replaced it.

But as I am going to tradfri, I replaced the whole transformer in the meantime, so I have a remote left... in germany...

Regards
Leonard
Reply Quote 0
1 Reply Last reply

2
Posts

39
Views

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

4

0
Votes

4
Posts

2577
Views

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
CHATGPT My new best friend!
General Discussion • • Tmaster

5

3
Votes

5
Posts

22
Views

@Tmaster I think it writes better code than a lot of code I've seen, and the documentation is a lot better. The latter, of course, is because most coders don't document. some key elements: good statement of work -- Purpose of the Code is key (did you write that? Good job!). This will guide the AI to write what you want. descriptive variables good documentation code is independent of reading sensors up-to-down/down-to-up I spent a couple hours analyzing, researching and writing and re-writing this and all I can say is that the AI didn't catch is, as far as I can see, if your sensors are too far apart or your magnet is too weak, you could get false readings. You, being the author of AI directive, are responsible for for the code. The AI is just a tool. I started my coding with assembly language, though at that time we still had to enter the binary on some machines (set 16 switches, then press commit). ForTran and COBOL were the first real high level languages and subsequent languages, pascal, c, java, etc. were improvements. AI is a quantum step. It's still coding, but you have to learn how to talk to the AI to get what you want. Good project! Let us know how it turns out and if you had to tweak the code. -OSD
AI: What is the future of Wikis and Forums?
General Discussion • • Eme

5

1
Votes

5
Posts

33
Views

@Homer I take care to say Good morning Sir, and Thank you Sir... You never know when it comes back to bite my tail.
set hostname using static IP
General Discussion • mysensors hostname static • • sandorhoffmann

2

0
Votes

2
Posts

9
Views

@sandorhoffmann I hope there is someone that can answer your question. But, I really recommend using DHCP. In that way, you can control all of your IPaddresses in one place, your DHCP server (almost always, your router) The huge advantage of ESP devices over Arduino is the WiFi. You don't need a big library. The MAC address is hard coded at the factory. I'm not sure that you can change it, which you would want to do if a device failed and you need an EXACT replacement. The downside of ESP is also the WiFi. Most home routers can only handle 20-30 WiFi devices My Asus routers start dropping WiFi devices resulting in difficult reconnects. The network becomes unusable. Because I have many ESP devices, I employed a Ubiquity access point that can handle 300 WiFi devices. The routers can handle 254 (253?) IP assignments, though some only allow 64 DHCP assignments. There is a discussion on this forum someplace on the number of clients there can be in a MySensors network. In theory 254 (253?) is the max, though I am unaware if anyone has tested it. I use an RPi as my gateway and haven't had problems with too many devices. If one is considering a very large number I would recommend starting each sensors one at a time because the gateway way will assign the NodeID which gets written into location 0 of the EEPROM. Or burn a NodeID into the Arduino EEPROM before running the actual code. bottom line, you didn't do anything wrong, its the nature of the beast.
Keen to build again
General Discussion • • Homer

9

0
Votes

9
Posts

54
Views

MySensors is an EXCELLENT project. It allows for complete control over the various sensors. It's extremely simple. Its drawback is that it's open source, so it's unfunded and development is slow, but I don't think there are any better projects than this at the moment.

Ikea utrusta ansluta

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

CHATGPT My new best friend!
General Discussion • • Tmaster

AI: What is the future of Wikis and Forums?
General Discussion • • Eme

set hostname using static IP
General Discussion • mysensors hostname static • • sandorhoffmann

Keen to build again
General Discussion • • Homer

14
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Ikea utrusta ansluta

Suggested Topics

Update RF24 library to latest version Bug Reports • • andriej

CHATGPT My new best friend! General Discussion • • Tmaster

AI: What is the future of Wikis and Forums? General Discussion • • Eme

set hostname using static IP General Discussion • mysensors hostname static • • sandorhoffmann

Keen to build again General Discussion • • Homer

14Online

11.7kUsers

11.2kTopics

113.0kPosts

Update RF24 library to latest version
Bug Reports • • andriej

CHATGPT My new best friend!
General Discussion • • Tmaster

AI: What is the future of Wikis and Forums?
General Discussion • • Eme

set hostname using static IP
General Discussion • mysensors hostname static • • sandorhoffmann

Keen to build again
General Discussion • • Homer

14
Online

11.7k
Users

11.2k
Topics

113.0k
Posts