MyS not working on solar sensor board

[ceech]

I don't, sorry.

[Sergio Rius]

What I can't understand is why the board has been working more than one week with the SFE_BMP180 library, to the point that I was doing adjustments and now I must work with sparkfun one's.

Well, then that sensor will be of no use.

Temperature: 28.39 degrees C
Temperature: 83.10 degrees F
Pressure: 101515.85 Pa
Altitude: -16.42m
Altitude: -53.86ft
%RH: 55.80 %

The temperature and humidity are off more than three points and altitude by 50mts.

[ceech]

Give it a while. It's new. It will calibrate in time. Also you can calibrate it yourself.

[ceech]

The BMP180 sensor is from the same family. Parts of the code probably works on both.

[Sergio Rius]

Ok, so leaving the sensor aside, this is the correct position for the NRF radio module?

First I'd directly soldered it, but as it wasn't working I desoldered it, resoldered a connector and tested with all my NRF modules, even with the ones on duty. The board always outputs a radio error:

0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
4 TSM:INIT
4 TSF:WUR:MS=0
6 RF24:write register, reg=0, value=14
14 RF24:write register, reg=3, value=3
18 RF24:write register, reg=4, value=95
22 RF24:write register, reg=5, value=76
26 RF24:write register, reg=6, value=39
30 RF24:write register, reg=16, value=115
36 RF24:write register, reg=29, value=6
40 RF24:read register, reg=6, value=255
45 RF24:read register, reg=5, value=255
49 !RF24:INIT:SANCHK FAIL
51 !TSM:INIT:TSP FAIL
53 TSM:FAIL:CNT=1
55 TSM:FAIL:PDT
57 RF24:write register, reg=0, value=12
61 RF24:PD

Also with MySensors version 2.0.0:

Starting sensor (RNNNA-, 2.0.0)
TSM:INIT
RF24:write register, reg=0, value=14
RF24:write register, reg=3, value=3
RF24:write register, reg=4, value=95
RF24:write register, reg=5, value=76
RF24:write register, reg=6, value=39
RF24:read register, reg=6, value=255
RF24:read register, reg=5, value=255
RF24:Sanity check failed: configuration mismatch! Check wiring, replace module or non-P version
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
RF24:write register, reg=0, value=12
RF24:power down

@ceech Do you have a mysensors working board? Which version?
Could this be a faulty one or something must be configured for mysensors?

[ceech]

I can't say what's wrong. Can you send it back and I'll take a look at it?

[Sergio Rius]

I can, just send me your address through MP or to my email.

Is the following configuration right for the resistor values you modified for my 7.2v batt?

float R1 = 47000.0; // resistance of R1
float R2 = 10000.0; // resistance of R2

You can also send me a working sketch and I'll upload and test it for you.

[ramwal]

@Sergio-Rius
It is a long time ago, but did you ever get a chance to solve the problem with this board? I have exactly the same problem as you explained in your message. In the past I bought a few of these boards, but never got so far to use them. Now I want to try them and @ceech is not appearing anymore on the forum.

[skywatch]

@ramwal Have you made the line "const float ALTITUDE = " correct for your location in the sketch?

[ramwal]

@skywatch
Yes, I did filled in the altitude, but I think that's not the problem, because after starting the program it stays with the sanity check fail of the radio Nrf24l01, with the verbose debug. So it has definitely to do with this particular board and the radio. The radio's I use are working on other standard Arduino's. So the radio is OK. It is sad, that the board is not supported anymore by its creator!!

I do not know how to go further! I can not make sense of the output. Anyway thanks for reacting.
See here the verbose debug output:

15:19:06.087 ->  
15:19:06.087 ->  __  __       ____
15:19:06.087 -> |  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
15:19:06.087 -> | |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
15:19:06.123 -> | |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
15:19:06.123 -> |_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
15:19:06.123 ->         |___/                      2.3.2
15:19:06.123 -> 
15:19:06.123 -> 16 MCO:BGN:INIT NODE,CP=RNNNA---,FQ=8,REL=255,VER=2.3.2
15:19:06.123 -> 28 TSM:INIT
15:19:06.123 -> 28 TSF:WUR:MS=0
15:19:06.123 -> 30 RF24:INIT:PIN,CE=9,CS=10
15:19:06.123 -> 34 RF24:SBY
15:19:06.157 -> 34 RF24:WBR:REG=0,VAL=14
15:19:06.157 -> 43 RF24:WBR:REG=3,VAL=3
15:19:06.157 -> 45 RF24:WBR:REG=4,VAL=95
15:19:06.157 -> 47 RF24:WBR:REG=5,VAL=76
15:19:06.157 -> 51 RF24:WBR:REG=6,VAL=37
15:19:06.157 -> 53 RF24:WBR:REG=29,VAL=4
15:19:06.157 -> 55 RF24:RBR:REG=29,VAL=255
15:19:06.157 -> 59 RF24:WBR:REG=16,VAL=115
15:19:06.157 -> 61 RF24:WBR:REG=29,VAL=4
15:19:06.157 -> 63 RF24:RBR:REG=6,VAL=255
15:19:06.157 -> 67 !RF24:INIT:SANCHK FAIL
15:19:06.157 -> 69 !TSM:INIT:TSP FAIL
15:19:06.190 -> 71 TSM:FAIL:CNT=1
15:19:06.190 -> 73 TSM:FAIL:DIS
15:19:06.190 -> 75 TSF:TDI:TSL
15:19:06.190 -> 77 RF24:SLP
15:19:06.190 -> 77 RF24:WBR:REG=0,VAL=12
15:19:16.161 -> 10082 TSM:FAIL:RE-INIT
15:19:16.161 -> 10084 TSM:INIT
15:19:16.161 -> 10086 RF24:INIT:PIN,CE=9,CS=10
15:19:16.194 -> 10088 RF24:SBY
15:19:16.194 -> 10090 RF24:WBR:REG=0,VAL=14
15:19:16.194 -> 10098 RF24:WBR:REG=3,VAL=3
15:19:16.194 -> 10100 RF24:WBR:REG=4,VAL=95
15:19:16.194 -> 10104 RF24:WBR:REG=5,VAL=76
15:19:16.194 -> 10106 RF24:WBR:REG=6,VAL=37
15:19:16.194 -> 10110 RF24:WBR:REG=29,VAL=4
15:19:16.194 -> 10113 RF24:RBR:REG=29,VAL=255
15:19:16.194 -> 10117 RF24:WBR:REG=16,VAL=115
15:19:16.194 -> 10119 RF24:WBR:REG=29,VAL=4
15:19:16.194 -> 10123 RF24:RBR:REG=6,VAL=255
15:19:16.194 -> 10125 !RF24:INIT:SANCHK FAIL
15:19:16.227 -> 10129 !TSM:INIT:TSP FAIL
15:19:16.227 -> 10131 TSM:FAIL:CNT=2
15:19:16.227 -> 10133 TSM:FAIL:DIS
15:19:16.227 -> 10135 TSF:TDI:TSL
15:19:16.227 -> 10137 RF24:SLP

[rvendrame]

@ramwal

These boards use a different CE and CS pins in Arduino. Try to add this BEFORE the #include <MySensors.h>:

#define MY_RF24_CE_PIN 7 // Ceech Arista board 
#define MY_RF24_CS_PIN 8 // Ceech Arista board
// Includes -------------------------------------------
#include <MySensors.h> 

[skywatch]

@ramwal I have no experience of that board. You can only test all attached modules on other known working nodes. You could also try without mysensors in the sketch just to see. Finally the usual magnifying glass inspection of the PCB and all connections, solder joints etc.... But while typing this you got a really good lead from @rvendrame :)

[ramwal]

@rvendrame
That was IT!! All working splendid now. I am very grateful to you. The debug log gives information on the CE and CS pin. I never knew this!!

@skywatch
Indeed a really good lead from @rvendrame.
Both thanks for your attention.

[rvendrame]

@ramwal I'm glad you got it working!

[Sergio Rius]

@ramwal I'm sorry for my late response. And I'm glad you solved your problem.
In my case, the board just kept giving problems and problems.
It started with aberrant readings from the sensors. I sent it back only to be told that the board was perfect.
When it came back I had a condenser failure and after the fix, intermittent serial bus fail (all leds on and hangs at simple debug prints)...

...until one day, it mysteriously jumped into a rain puddle (while still connected to the battery pack, from a considerable height). So I said bye and never look back.
:blush: