Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

I am planning to use this PCB to power 8 x Servo motors consuming max 850mA each so around 7A Peak, I see the PCB is designed for a 1,8A max, do you think it makes any sense ?

veynacal last edited by

Re: Power path manager and battery charger w/ 5V and 3.3V output
Reply Quote 0
1 Reply Last reply

1
Posts

13
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50408
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
Which one should i choose? PIR or microwave sensor
Hardware • • h01

8

0
Votes

8
Posts

69
Views

Supposedly PIR doesn't work through glass (e.g. if looking for motion through a window), whereas I presume a microwave sensor might still work.
Sleep mode for bmp280
Hardware • • fishermans

7

4
Votes

7
Posts

3279
Views

Just wanted to say thanks for this, it is still relevant and useful six years later !
Sensors and more
Hardware • • Robert Leverett

1

0
Votes

1
Posts

15
Views

No one has replied
hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

5

0
Votes

5
Posts

27
Views

@Tmaster Never assume the original PCB was just a circuit of components, the PCB can incorporate RF shields and antenna radio ground planes...
"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

10

0
Votes

10
Posts

42
Views

@wrendral said in "Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design": I will go with a Li-Po Battery type: 304048 3.7V 1200mAh Might work, but maybe the internal protection will trigger with the high current peaks. I'd suggest you plan a 0 Ohm, (2512/THT) resistor as R2 and then replace it with a 100Ohm/1Watt if the protection triggers.

I am planning to use this PCB to power 8 x Servo motors consuming max 850mA each so around 7A Peak, I see the PCB is designed for a 1,8A max, do you think it makes any sense ?

Suggested Topics

Over the air updates
General Discussion • • ToSa

Which one should i choose? PIR or microwave sensor
Hardware • • h01

Sleep mode for bmp280
Hardware • • fishermans

Sensors and more
Hardware • • Robert Leverett

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

23
Online

11.2k
Users

11.1k
Topics

112.5k
Posts

I am planning to use this PCB to power 8 x Servo motors consuming max 850mA each so around 7A Peak, I see the PCB is designed for a 1,8A max, do you think it makes any sense ?

Suggested Topics

Over the air updates General Discussion • • ToSa

Which one should i choose? PIR or microwave sensor Hardware • • h01

Sleep mode for bmp280 Hardware • • fishermans

Sensors and more Hardware • • Robert Leverett

hlk-pm01 are to noisy for rfm69? Hardware • • Tmaster

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design" Hardware • • wrendral

23Online

11.2kUsers

11.1kTopics

112.5kPosts

Over the air updates
General Discussion • • ToSa

Which one should i choose? PIR or microwave sensor
Hardware • • h01

Sleep mode for bmp280
Hardware • • fishermans

Sensors and more
Hardware • • Robert Leverett

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

23
Online

11.2k
Users

11.1k
Topics

112.5k
Posts