Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

MySensors and Arduino IDE 1.6.7

Tom71 last edited by Tom71

Hello, i have Problems to compile MySensors Serial Gateway with the latest Adruino IDE 1.6.7 and the development Version from MySensors. There is no USBDevice.init() anymore. I disabled the call in MyMainDefault.cpp and it compiles an works fine. Is this an workaround?
Thomas
Reply Quote 0
1 Reply Last reply

1
Posts

822
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3303
Views

No one has replied
Sensebender Gateway (SAMD21)
Development • • pikim

10

0
Votes

10
Posts

54
Views

Just for completeness: the right way to do this is to add the json under ~/.platformio/boards and the other files as described in https://community.platformio.org/t/how-use-a-same-chip-but-with-different-environment/18082/4
Serial Gateway woes
Development • • OldSurferDude

1

0
Votes

1
Posts

9
Views

No one has replied
problem with Dallas temperature
Development • • mickaelr30

3

0
Votes

3
Posts

17
Views

hello, I just deleted the eeprom but I still have the problem.
MYSBootloader 1.3 pre-release & MYSController 1.0.0beta
Development • ota myscontroller mysbootloader • • tekka

198

13
Votes

198
Posts

84985
Views

@tekka Is there any changelog to it also or it was just made officially available again? although last online status was 22 AUG 2020, so anyone else can confirm anything about it? I'd just be cautious without confirmation.
How control W5500/W5100 (with STM32) by mysensors library
Development • • Marcin

2

0
Votes

2
Posts

17
Views

I found procedure gatewayTransportInit(), it works great. However, I cannot find a procedure that will enable detection of a network connection at level mysensors. I noticed that disconnecting the network plug or resetting the W5500 (37 pin to ground) changes the device's IP address to 0.0.0.0 - then I call gatewayTransportInit() - but mysensor's library must have such procedures - please tell me how to diagnose ethernet connection.

MySensors and Arduino IDE 1.6.7

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Sensebender Gateway (SAMD21)
Development • • pikim

Serial Gateway woes
Development • • OldSurferDude

problem with Dallas temperature
Development • • mickaelr30

MYSBootloader 1.3 pre-release & MYSController 1.0.0beta
Development • ota myscontroller mysbootloader • • tekka

How control W5500/W5100 (with STM32) by mysensors library
Development • • Marcin

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts

MySensors and Arduino IDE 1.6.7

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

Sensebender Gateway (SAMD21) Development • • pikim

Serial Gateway woes Development • • OldSurferDude

problem with Dallas temperature Development • • mickaelr30

MYSBootloader 1.3 pre-release & MYSController 1.0.0beta Development • ota myscontroller mysbootloader • • tekka

How control W5500/W5100 (with STM32) by mysensors library Development • • Marcin

0Online

11.2kUsers

11.1kTopics

112.5kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Sensebender Gateway (SAMD21)
Development • • pikim

Serial Gateway woes
Development • • OldSurferDude

problem with Dallas temperature
Development • • mickaelr30

MYSBootloader 1.3 pre-release & MYSController 1.0.0beta
Development • ota myscontroller mysbootloader • • tekka

How control W5500/W5100 (with STM32) by mysensors library
Development • • Marcin

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts