Help troubleshooting code

[martinhjelmare]

@barduino

Don't confuse MOTION_A_TRIGGER_PIN with MOTION_A_CHILD_ID.

[barduino]

@martinhjelmare

You're right it should be MOTION_A_TRIGGER_PIN. And it should be -1 not -2 confirm?

[martinhjelmare]

@barduino

The interrupt number is usually pin - 2 on our boards. But I would rather use the function provided by arduino to get the correct interrupt number for a pin, digitalPinToInterrupt.

[Cliff Karlsson]

Thanks for the help, the sketch complies and runs now. But where and how do I specify the timing in the sketch. This is what I want.

1 PIR detects movement
2 PIR is disabled for 30 seconds
3 Both ultrasonic sensors is enbabled for 30 seconds
4 Ultrasonic sensors OFF PIR ON
5 --> Step one

[Cliff Karlsson]

I don't really understand how the sketch that I posted works. After motionsensor detects movement the loop under

if (tripped)

runs, but for how long are the ultrasonic sensors active? And how do I make it so that they are active for 30 sec before they are disabled and the PIR starts again.

[martinhjelmare]

@Cliff-Karlsson

Should the node sleep in between pinging during the 30 secs that the sonars should be active?

[Cliff Karlsson]

@Cliff-Karlsson said:

I don't really understand how the sketch that I posted works. After motionsensor detects movement the loop under

No I only want the sensor to sleep until it gets interrupted from the PIR. Then I want the ultrasonic sensors to ping continuously during the 30 secs.

[martinhjelmare]

Right now there's a call to wait method in between A and B pings, waiting 1 second. Is that intended? For 30 secs, ping A and B alternatively every 1 second?

[Cliff Karlsson]

@martinhjelmare

Well I thing the sketch was created mostly using copy/paste so that bit is not exactly what I wanted.

For 30secs, ping A and B alternatively every 100ms would probably be better.

[Cliff Karlsson]

I don't understand where and how I should specify that the ultrasonic part should run for 30 sec.

void loop()      
{     
  
  boolean tripped = digitalRead(MOTION_A_TRIGGER_PIN) == HIGH; 
  
    
  Serial.println(tripped);
  send(MOTION_A_msg.set(tripped?"1":"0"));  // Send tripped value to gw 
 if(tripped)  {
  
  int SONAR_A_dist = metric?sonar_A.ping_cm():sonar_A.ping_in();
  Serial.print("Ping Sonar A: ");
  Serial.print(SONAR_A_dist); // Convert ping time to distance in cm and print result (0 = outside set distance range)
  Serial.println(metric?" cm":" in");

  if (SONAR_A_dist != SONAR_A_lastDist) {
      send(SONAR_A_msg.set(SONAR_A_dist));
      SONAR_A_lastDist = SONAR_A_dist;
  }
  
  wait(1000);

  int SONAR_B_dist = metric?sonar_B.ping_cm():sonar_B.ping_in();
  Serial.print("Ping Sonar B: ");
  Serial.print(SONAR_B_dist); // Convert ping time to distance in cm and print result (0 = outside set distance range)
  Serial.println(metric?" cm":" in");

  if (SONAR_B_dist != SONAR_B_lastDist) {
      send(SONAR_B_msg.set(SONAR_B_dist));
      SONAR_B_lastDist = SONAR_B_dist;
  }

  sleep(SLEEP_TIME);
}
            }
//else{
  // Sleep until interrupt comes in on motion sensor. Send update every two minute. 
  sleep(INTERRUPT,CHANGE, MOTION_SLEEP_TIME);```

[martinhjelmare]

You have to add a timer, and an if statement. Start the timer after motion is tripped. If time is less than 30 s, ping. Else reset timer and sleep with motion interrupt.

I can post some example code later perhaps.