RFID Garage door opener

Anticimex

Cool stuff! You probably what some signing in there as well :) would be a shame if someone snooped the open command from your controller and decided to pay a visit.

BartE

@SVLoneStar That should work, did you try the sketch shown in the topic?

The function recallEeprom(); reads the EEPROM content and after closing the program mode this function storeEeprom();
writes the EEPROM. Please add some debug info (Serial.print) and validate that these functions actually are called on

recallEeprom(); --> on start up
storeEeprom(); --> ending program mode.

BartE

@Anticimex yes your right but when i wrote this sketch signing was not in the released branch.

Rod MacPherson

Nice work. I have yet to pick up an RFID reader to give that part of it a try, but I've modified it a little to have reed sensors for the 2 doors so that I can easily see if the door is open on my phone, and get notifications when the door opens at an unexpected time, like when the controller is set to vacation mode, or at times of night when we would not normally be coming and going.
I'll be watching for someone to post up a signing version.

Here's my 2 relay, 2 door sensor version.

/*
 RFID Garagedoor opener by Bart Eversdijk
 Modified to add door sensors by Rod MacPherson
 
 This sketch is to open a Garage door with an mifare RIFD-tag 
  
  For an Arduino Nano v3
  Connection wiring :
    - nrf24l01+ as descibed on the MySensors website
    - MFRC522 reader/writer MOSI, MISO, SCK, 3.3V and GND as they are on the nrf24101+, but connect RST to pin D7 and connect SDA(SS) to pin D8 
    - LED with 470ohm resistor between GND and pin A3 
    - push button between GND and pin D5
    - 5v relays coil between GND and  pin D4 -> switch pins of the relays should be connected in parallel with your garage door push button. 
    - second relay for second door on pin D3
    
  Features:
  This project can record up to 18 RFID-"tags"
  These card IDs are stored in to EEPROM by keeping them next to the RFID reader when the system in program mode. (Slow blinking LED) When a card is accepted as new card the LED will blink fast for a short time.
  To keep the master-tags (choose your own) next to the RFID reader when pressing the push button. To clear all cards (except the master card) press the push button in program mode for 6 seconds. The LED will now fast blink for a couple of seconds.
  
  Your garage your can be opened by keep a registered RFID tag next to the reader or by clicking the open icon on lock node presented by this plugin.
  By by-passing the alarm node presented by this plug in the RFID will be temporarily disabled.
  When an incorrect (not registered) RFID tag is scanned the alarm is triggered to detect illegal scan attempts   

*/

#include <SPI.h>
#include <MFRC522.h>
#include <MySensor.h> 
#include <Bounce2.h>

#define RF_INIT_DELAY   125
#define ONE_SEC         1000
#define MAX_CARDS       18
#define PROG_WAIT       10
#define HEARTBEAT       10
#define BAUD            115200

/*Pin definitions*/
#define LED_PIN         A3
#define SECONDRELAY     3
#define GARAGEPIN       4
#define SWITCH_PIN      5
#define RST_PIN         7       //  MFRC 
#define SS_PIN          8       //  MFRC 
#define DOOR_PIN_L  A0  // Arduino Digital I/O pin for button/reed switch
#define DOOR_PIN_R  A1  // Arduino Digital I/O pin for button/reed switch


MFRC522      mfrc522(SS_PIN, RST_PIN);  // Create MFRC522 instance
MFRC522::Uid olduid;
MFRC522::Uid masterkey = { 10, {0,0,0,0, 0,0,0,0, 0,0 },  0 };

byte       countValidCards  = 0;
MFRC522::Uid validCards[MAX_CARDS];

void       ShowCardData(MFRC522::Uid* uid);
bool       sameUid(MFRC522::Uid* old, MFRC522::Uid* check);
void       copyUid(MFRC522::Uid* src, MFRC522::Uid* dest);
bool       isValidCard(MFRC522::Uid* uid);
int        releasecnt = 0;

#define    CHILD_ID_ALARM    1
#define    CHILD_ID_LOCK     2
#define    CHILD_ID_LOCK2    3
#define    CHILD_ID_DOOR_L    4
#define    CHILD_ID_DOOR_R    5

MySensor   gw;
Bounce     debouncer = Bounce();
Bounce     debouncerDoorR = Bounce();
Bounce     debouncerDoorL = Bounce();
int oldValueR=-1;
int oldValueL=-1;

int        oldSwitchValue=-1;
int        switchValue = 0;
long       timer = -1;
bool       programmode = false;
bool       ledon;
int        programTimer = 0;
bool       armed = true;
unsigned long lastTime = 0;

MyMessage  lockMsg(CHILD_ID_LOCK,          V_LOCK_STATUS);
MyMessage  lock2Msg(CHILD_ID_LOCK2,          V_LOCK_STATUS);
MyMessage  lockArmMsg(CHILD_ID_ALARM,      V_ARMED);
MyMessage  wrongMsg(CHILD_ID_ALARM,        V_TRIPPED);
MyMessage  doorRmsg(CHILD_ID_DOOR_R, V_TRIPPED);
MyMessage  doorLmsg(CHILD_ID_DOOR_L, V_TRIPPED);

void setup() {
        Serial.begin(BAUD);     // Initialize serial communications with the PC
        pinMode(GARAGEPIN, OUTPUT);     // Initialise in/output ports
        pinMode(SECONDRELAY, OUTPUT);     // Initialise in/output ports
        
        // Make sure MFRC will be disabled on the SPI bus
        pinMode(RST_PIN, OUTPUT);     
        digitalWrite(RST_PIN, LOW);
        pinMode(SS_PIN, OUTPUT);     
        digitalWrite(SS_PIN, LOW);

        pinMode(LED_PIN, OUTPUT);
        digitalWrite(LED_PIN, LOW);
        // Setup the button
        pinMode(SWITCH_PIN, INPUT_PULLUP);

        // After setting up the button, setup debouncer
        debouncer.attach(SWITCH_PIN);
        debouncer.interval(5);

        // Setup the right door sensor
        pinMode(DOOR_PIN_R,INPUT);
        // Activate internal pull-up
        digitalWrite(DOOR_PIN_R,HIGH);
  
        // After setting up the button, setup debouncer
        debouncerDoorR.attach(DOOR_PIN_R);
        debouncerDoorR.interval(5);
        
        // Setup the left door sensor
        pinMode(DOOR_PIN_L,INPUT);
        // Activate internal pull-up
        digitalWrite(DOOR_PIN_L,HIGH);
  
        // After setting up the button, setup debouncer
        debouncerDoorL.attach(DOOR_PIN_L);
        debouncerDoorL.interval(5);
  

        // Init mysensors library
        gw.begin(incomingMessage, 5);
        gw.sendSketchInfo("RFID Garage", "1.2"); delay(RF_INIT_DELAY);
        
        // Register all sensors to gw (they will be created as child devices)
        gw.present(CHILD_ID_LOCK, S_LOCK);      delay(RF_INIT_DELAY);
        gw.present(CHILD_ID_LOCK2, S_LOCK);      delay(RF_INIT_DELAY);
        gw.present(CHILD_ID_ALARM, S_MOTION);   delay(RF_INIT_DELAY);
        gw.present(CHILD_ID_DOOR_R, S_DOOR); 
        gw.present(CHILD_ID_DOOR_L, S_DOOR); 
        
        recallEeprom();
        
        // Init MFRC RFID sensor
        SPI.begin();            // Init SPI bus
        mfrc522.PCD_Init();     // Init MFRC522
        ShowReaderDetails();            // Show details of PCD - MFRC522 Card Reader details

        gw.send(lockArmMsg.set(armed));
        Serial.println(F("Init done..."));
}

void loop() {
        timer++;
        delay(HEARTBEAT);
        gw.process();
        debouncer.update();
        debouncerDoorL.update();
        // Get the update value for Left
        int valueL = debouncerDoorL.read(); 
        if (valueL != oldValueL) {
           // Send in the new value for Left
           gw.send(doorLmsg.set(valueL==HIGH ? 1 : 0));
           oldValueL = valueL;
        }
        debouncerDoorR.update();
        // Get the update value for Right
        int valueR = debouncerDoorR.read();
        if (valueR != oldValueR) {
           // Send in the new value for Right
           gw.send(doorRmsg.set(valueR==HIGH ? 1 : 0));
           oldValueR = valueR;
        }

        // Get the update value
        int switchValue = debouncer.read();
        if (switchValue != oldSwitchValue) {
          // Send in the new value
          Serial.print (F("Switch "));
          Serial.println (switchValue);
          
          if (switchValue && programmode) {
               lastTime     = millis() / 1000;
          }
          
          if (!switchValue && programmode && lastTime > 0) {
               if ( (millis() / 1000) - lastTime > 3) {
                    Serial.println(F("Reset all cards"));  
                    countValidCards  = 0;
                    blinkFast(50);
               } else {
                  Serial.println(F("Program off"));  
                  digitalWrite(LED_PIN, LOW);
                  programmode = false;
                  
                  storeEeprom();
               }
          }
          
          if (!switchValue)   {
              programTimer = 0;
          }
          oldSwitchValue = switchValue;
        }
        
        if (programmode && ((timer % (ONE_SEC / HEARTBEAT)) == 0 ))  {
            ledon = !ledon;
            digitalWrite(LED_PIN, ledon);
            programTimer++;

            // Stop program mode after 20 sec inactivity
            if (programTimer > PROG_WAIT)  {
               programmode = false;
               digitalWrite(LED_PIN, false);
               Serial.println(F("Program expired"));  
            }
        }
        
        if ((timer % (200 / HEARTBEAT)) == 0 )   {
             // Look for new cards
             if ( ! mfrc522.PICC_IsNewCardPresent()) {
                  if (releasecnt > 0)   {
                      releasecnt--;
                      if (!releasecnt)  {
                          olduid.size = 0;
                          Serial.println(F("release"));
                      }
                    }
            return;
            }
            releasecnt = 5;
    
           // Select one of the cards
           if ( ! mfrc522.PICC_ReadCardSerial()) {
              return;
           }
    
           // Dump debug info about the card; PICC_HaltA() is automatically called
           //mfrc522.PICC_DumpToSerial(&(mfrc522.uid));
           if (!olduid.size || !sameUid(&(mfrc522.uid), &olduid))  {
                ShowCardData(&(mfrc522.uid));
                copyUid(&(mfrc522.uid), &olduid);
                if ( isValidCard(&olduid) )   {
                     OpenDoor(programmode);
                } else  {
                   if (sameUid(&(mfrc522.uid), &masterkey)) {
                       // Only switch in program mode when mastercard is found AND the program button is pressed
                       if (switchValue)  {
                         Serial.println(F("Program mode"));
                         programmode = true;
                         programTimer = 0;
                         lastTime     = 0;
                       } else {
                         OpenDoor2(programmode);
                       }
                   } else {
                       if (programmode) {
                         Serial.println(F("new card"));
                         programTimer = 0;
                         
                         if (countValidCards < MAX_CARDS)
                         {
                            // Add card to list...
                            copyUid(&(mfrc522.uid), &validCards[countValidCards]);
                            countValidCards++;
                            blinkFast(15);
                         }
                       } else {
                         Serial.println(F("Invalid card"));
                         if (armed) {
                            gw.send(wrongMsg.set(1));
                            delay(2000);
                            gw.send(wrongMsg.set(0));
                         }
                       }
                   }
                }
           }
        }
}

void ShowCardData(MFRC522::Uid* uid) 
{
    Serial.print(F("Card UID:"));
    for (byte i = 0; i < uid->size; i++) {
        if(uid->uidByte[i] < 0x10) {
            Serial.print(F(" 0"));
        } else {
            Serial.print(F(" "));
                }
        Serial.print(uid->uidByte[i], HEX);
    } 
    Serial.println();
}

void copyUid(MFRC522::Uid* src, MFRC522::Uid* dest)
{
    dest->size = src->size;
    dest->sak  = src->sak;
    
    for (byte i = 0; i < src->size; i++) {
    dest->uidByte[i] = src->uidByte[i];
    }
}

bool sameUid(MFRC522::Uid* old, MFRC522::Uid* check)
{
    if (old->size != check->size) {
       return false;
    }
    for (byte i = 0; i < old->size; i++) {
        if (old->uidByte[i] != check->uidByte[i]) {
            return false;
        }
    }
    return true;
}

bool isValidCard(MFRC522::Uid* uid)
{
      for (byte i = 0; i < countValidCards; i++)  {
          if (validCards[i].size != uid->size)  {
              break;
          }
          for (int j = 0; j < uid->size; j++) {
              if (validCards[i].uidByte[j] != uid->uidByte[j])  {
                  break;
              }
              if (j == (uid->size - 1)) {  
                  return true;
              }
          }
      }
      return false;
}


void storeEeprom()
{
    byte address = 0;
    gw.saveState(address++, countValidCards);
    
    for (byte i = 0; i < countValidCards; i++) {
       gw.saveState(address++, validCards[i].size);
       for (byte j = 0; j < 10; j++) {
          gw.saveState(address++, validCards[i].uidByte[j]);
       } 
    }
}

void recallEeprom()
{
    byte address = 0;
    
    countValidCards = gw.loadState(address++);
    if (countValidCards > MAX_CARDS) {
       Serial.println(F("Not a valid EEPROM reading set to default"));
       countValidCards = 0;
       storeEeprom();
       return;
    }
    
    for (byte i = 0; i < countValidCards; i++)  {
       validCards[i].size = gw.loadState(address++);
       for (byte j = 0; j < 10; j++)  {
          validCards[i].uidByte[j] = gw.loadState(address++);
       } 
    }
  
}

void blinkFast(int times)
{
    for (int i = 0; i < times; i++) { 
       ledon = !ledon;
       digitalWrite(LED_PIN, ledon);
       delay(100);
    }
}

void OpenDoor(bool fakeOpen)
{
    Serial.println(F("Open door!"));
    gw.send(lockMsg.set(false));
    
    if (!fakeOpen) { 
      digitalWrite(LED_PIN, HIGH);
      digitalWrite(GARAGEPIN, HIGH); 
    }
    delay(1000);
    
    if (!fakeOpen) { 
      digitalWrite(GARAGEPIN, LOW); 
      digitalWrite(LED_PIN, LOW);
    }
    
    gw.send(lockMsg.set(true));
}

void OpenDoor2(bool fakeOpen)
{
    Serial.println(F("Open door 2!"));
    gw.send(lock2Msg.set(false));
    
    if (!fakeOpen) { 
      digitalWrite(LED_PIN, HIGH);
      digitalWrite(SECONDRELAY, HIGH); 
    }
    delay(1000);
    
    if (!fakeOpen) { 
      digitalWrite(SECONDRELAY, LOW); 
      digitalWrite(LED_PIN, LOW);
    }
    
    gw.send(lock2Msg.set(true));
}

void ShowReaderDetails() {
    // Get the MFRC522 software version
    byte v = mfrc522.PCD_ReadRegister(mfrc522.VersionReg);
    Serial.print(F("MFRC522 Software Version: 0x"));
    Serial.print(v, HEX);
    if (v == 0x91) {
        Serial.print(F(" = v1.0"));
        } else if (v == 0x92) {
        Serial.print(F(" = v2.0"));
        } else {
        Serial.print(F(" (unknown)"));
        }
    Serial.println("");
    
        // When 0x00 or 0xFF is returned, communication probably failed
    if ((v == 0x00) || (v == 0xFF)) {
        Serial.println(F("WARNING: Communication failure, is the MFRC522 properly connected?"));
    }
}


void incomingMessage(const MyMessage &message) 
{
   if (message.type == V_LOCK_STATUS) {
     // Change relay state
     if (!message.getBool())  {
        switch (message.sensor)
        {
           case CHILD_ID_LOCK:
              OpenDoor(false);
              break;
           case CHILD_ID_LOCK2:
              OpenDoor2(false);
              break;
        }
     }
  
     // Write some debug info
     Serial.print(F("Lock:  "));
     Serial.print(message.sensor);
     Serial.print(F(" status: "));
     Serial.println(message.getBool());
   }
   else 
   {
     if (message.type == V_ARMED)  {
       // Change relay state
       armed = message.getBool();
  
       // Write some debug info
       Serial.print(F("Arm status: "));
       Serial.println(message.getBool());
     }
     else
     {
       // Write some debug info
       Serial.print(F("Incoming msg type: "));
       Serial.print(message.type);
       Serial.print(F(" id: "));
       Serial.print(message.sensor);
       Serial.print(F(" content: "));
       Serial.println(message.getInt());
     }
   }
}

codergirl56

Hi @BartE - thanks for putting this together! It has been very helpful.

I am working on a project with two wireless MFRC522 modules and RFID Reader. I want to be able to read PICC cards with the RFID reader and send it the UID between the modules. So essentially a more bare version of the code you have written with the garage door opening code. I was wondering if you could help me out in simplifying the code to just reading the UID off the PICC cards and outputting that date between the RCF522 modules.

Thanks in advance.

BartE

@codergirl56 there are a number of examples in the MFRC522 library which might help you.
You can find them here: https://github.com/miguelbalboa/rfid

Please feel free to ask questions if the examples does not help you further

codergirl56

@BartE thanks for getting back to me. I've looked through the examples on the MFRC522 library. I think the main thing I'm struggling with is setting up and initializing the N24L01 module and the RFID on the same arduino uno. My plan is to have one N24L01 and RFID on one arduino module, and a second N24L01 on a second arduino. I want the RFID to read the UID off of PICC cards and be able to wirelessly transmit the UID between the N24L01 modules. I think it's simpler than the code you have written here, but I'm struggling to simplify the code you have to only what I need. Could you possibly walk through what each function in your program is used for? Thanks in advance.

BartE

@codergirl56 Oke i will give it a try:

Basic IO pin set up

void setup() {
        Serial.begin(BAUD);     // Initialize serial communications with the PC
        pinMode(GARAGEPIN, OUTPUT);     // Initialise in/output ports
        pinMode(SECONDRELAY, OUTPUT);     // Initialise in/output ports

This part initializes the SPI I/O pins used by the RFID reader so it release the SPI bus for thr NFR radio

        // Make sure MFRC will be disabled on the SPI bus
        pinMode(RST_PIN, OUTPUT);     
        digitalWrite(RST_PIN, LOW);
        pinMode(SS_PIN, OUTPUT);     
        digitalWrite(SS_PIN, LOW);

Init LED and button I/O-pin

        pinMode(LED_PIN, OUTPUT);
        digitalWrite(LED_PIN, LOW);
        // Setup the button
        pinMode(SWITCH_PIN, INPUT_PULLUP);

        // After setting up the button, setup debouncer
        debouncer.attach(SWITCH_PIN);
        debouncer.interval(5);

Init radion module

        // Init mysensors library
        gw.begin(incomingMessage, 5);
        gw.sendSketchInfo("RFID Garage", "1.2"); delay(RF_INIT_DELAY);
        
        // Register all sensors to gw (they will be created as child devices)
        gw.present(CHILD_ID_LOCK, S_LOCK);      delay(RF_INIT_DELAY);
        gw.present(CHILD_ID_LOCK2, S_LOCK);      delay(RF_INIT_DELAY);
        gw.present(CHILD_ID_ALARM, S_MOTION);   delay(RF_INIT_DELAY);

Read eeprom settings

        recallEeprom();

nit SPI bus for MFRC RFID sensor

        SPI.begin();            // Init SPI bus
        mfrc522.PCD_Init();     // Init MFRC522
        ShowReaderDetails();            // Show details of PCD - MFRC522 Card Reader details

        gw.send(lockArmMsg.set(armed));
        Serial.println(F("Init done..."));
}

void loop() {
        timer++;
        delay(HEARTBEAT);
        gw.process();
        debouncer.update();

        // Get the update value
        int switchValue = debouncer.read();
        if (switchValue != oldSwitchValue) {
          // Send in the new value
          Serial.print (F("Switch "));
          Serial.println (switchValue);
          
          if (switchValue && programmode) {
               lastTime     = millis() / 1000;
          }
          
          if (!switchValue && programmode && lastTime > 0) {
               if ( (millis() / 1000) - lastTime > 3) {
                    Serial.println(F("Reset all cards"));  
                    countValidCards  = 0;
                    blinkFast(50);
               } else {
                  Serial.println(F("Program off"));  
                  digitalWrite(LED_PIN, LOW);
                  programmode = false;
                  
                  storeEeprom();
               }
          }
          
          if (!switchValue)   {
              programTimer = 0;
          }
          oldSwitchValue = switchValue;
        }
        
        if (programmode && ((timer % (ONE_SEC / HEARTBEAT)) == 0 ))  {
            ledon = !ledon;
            digitalWrite(LED_PIN, ledon);
            programTimer++;

            // Stop program mode after 20 sec inactivity
            if (programTimer > PROG_WAIT)  {
               programmode = false;
               digitalWrite(LED_PIN, false);
               Serial.println(F("Program expired"));  
            }
        }
        
        if ((timer % (200 / HEARTBEAT)) == 0 )   {
             // Look for new cards
             if ( ! mfrc522.PICC_IsNewCardPresent()) {
                  if (releasecnt > 0)   {
                      releasecnt--;
                      if (!releasecnt)  {
                          olduid.size = 0;
                          Serial.println(F("release"));
                      }
                    }
            return;
            }
            releasecnt = 5;

Check if a RFID card is held at the RFID reader if not: skip the rest and start over with loop()

           // Select one of the cards
           if ( ! mfrc522.PICC_ReadCardSerial()) {
              return;
           }
    
           // Dump debug info about the card; PICC_HaltA() is automatically called
           //mfrc522.PICC_DumpToSerial(&(mfrc522.uid));

Check if this card is the same as the previous loop if not enter the IF loop

           if (!olduid.size || !sameUid(&(mfrc522.uid), &olduid))  {
                ShowCardData(&(mfrc522.uid));
                copyUid(&(mfrc522.uid), &olduid);
                if ( isValidCard(&olduid) )   {
                     OpenDoor(programmode);
                } else  {

Check if the master card was presented and the button was pressed enter program mode

                   if (sameUid(&(mfrc522.uid), &masterkey)) {
                       // Only switch in program mode when mastercard is found AND the program button is pressed
                       if (switchValue)  {
                         Serial.println(F("Program mode"));
                         programmode = true;
                         programTimer = 0;
                         lastTime     = 0;
                       } else {
                         OpenDoor2(programmode);
                       }
                   } else {

If not the master card and this card in not known and we're in program mode add this as a new card

                       if (programmode) {
                         Serial.println(F("new card"));
                         programTimer = 0;
                         
                         if (countValidCards < MAX_CARDS)
                         {
                            // Add card to list...
                            copyUid(&(mfrc522.uid), &validCards[countValidCards]);
                            countValidCards++;
                            blinkFast(15);
                         }
                       } else {
                         Serial.println(F("Invalid card"));
                         if (armed) {
                            gw.send(wrongMsg.set(1));
                            delay(2000);
                            gw.send(wrongMsg.set(0));
                         }
                       }
                   }
                }
           }
        }
}

These are support functions

void ShowCardData(MFRC522::Uid* uid) 
{
    Serial.print(F("Card UID:"));
    for (byte i = 0; i < uid->size; i++) {
        if(uid->uidByte[i] < 0x10) {
            Serial.print(F(" 0"));
        } else {
            Serial.print(F(" "));
                }
        Serial.print(uid->uidByte[i], HEX);
    } 
    Serial.println();
}

void copyUid(MFRC522::Uid* src, MFRC522::Uid* dest)
{
    dest->size = src->size;
    dest->sak  = src->sak;
    
    for (byte i = 0; i < src->size; i++) {
    dest->uidByte[i] = src->uidByte[i];
    }
}

bool sameUid(MFRC522::Uid* old, MFRC522::Uid* check)
{
    if (old->size != check->size) {
       return false;
    }
    for (byte i = 0; i < old->size; i++) {
        if (old->uidByte[i] != check->uidByte[i]) {
            return false;
        }
    }
    return true;
}

bool isValidCard(MFRC522::Uid* uid)
{
      for (byte i = 0; i < countValidCards; i++)  {
          if (validCards[i].size != uid->size)  {
              break;
          }
          for (int j = 0; j < uid->size; j++) {
              if (validCards[i].uidByte[j] != uid->uidByte[j])  {
                  break;
              }
              if (j == (uid->size - 1)) {  
                  return true;
              }
          }
      }
      return false;
}


void storeEeprom()
{
    byte address = 0;
    gw.saveState(address++, countValidCards);
    
    for (byte i = 0; i < countValidCards; i++) {
       gw.saveState(address++, validCards[i].size);
       for (byte j = 0; j < 10; j++) {
          gw.saveState(address++, validCards[i].uidByte[j]);
       } 
    }
}

void recallEeprom()
{
    byte address = 0;
    
    countValidCards = gw.loadState(address++);
    if (countValidCards > MAX_CARDS) {
       Serial.println(F("Not a valid EEPROM reading set to default"));
       countValidCards = 0;
       storeEeprom();
       return;
    }
    
    for (byte i = 0; i < countValidCards; i++)  {
       validCards[i].size = gw.loadState(address++);
       for (byte j = 0; j < 10; j++)  {
          validCards[i].uidByte[j] = gw.loadState(address++);
       } 
    }
  
}

void blinkFast(int times)
{
    for (int i = 0; i < times; i++) { 
       ledon = !ledon;
       digitalWrite(LED_PIN, ledon);
       delay(100);
    }
}

void OpenDoor(bool fakeOpen)
{
    Serial.println(F("Open door!"));
    gw.send(lockMsg.set(false));
    
    if (!fakeOpen) { 
      digitalWrite(LED_PIN, HIGH);
      digitalWrite(GARAGEPIN, HIGH); 
    }
    delay(1000);
    
    if (!fakeOpen) { 
      digitalWrite(GARAGEPIN, LOW); 
      digitalWrite(LED_PIN, LOW);
    }
    
    gw.send(lockMsg.set(true));
}

void OpenDoor2(bool fakeOpen)
{
    Serial.println(F("Open door 2!"));
    gw.send(lock2Msg.set(false));
    
    if (!fakeOpen) { 
      digitalWrite(LED_PIN, HIGH);
      digitalWrite(SECONDRELAY, HIGH); 
    }
    delay(1000);
    
    if (!fakeOpen) { 
      digitalWrite(SECONDRELAY, LOW); 
      digitalWrite(LED_PIN, LOW);
    }
    
    gw.send(lock2Msg.set(true));
}

void ShowReaderDetails() {
    // Get the MFRC522 software version
    byte v = mfrc522.PCD_ReadRegister(mfrc522.VersionReg);
    Serial.print(F("MFRC522 Software Version: 0x"));
    Serial.print(v, HEX);
    if (v == 0x91) {
        Serial.print(F(" = v1.0"));
        } else if (v == 0x92) {
        Serial.print(F(" = v2.0"));
        } else {
        Serial.print(F(" (unknown)"));
        }
    Serial.println("");
    
        // When 0x00 or 0xFF is returned, communication probably failed
    if ((v == 0x00) || (v == 0xFF)) {
        Serial.println(F("WARNING: Communication failure, is the MFRC522 properly connected?"));
    }
}


void incomingMessage(const MyMessage &message) 
{
   if (message.type == V_LOCK_STATUS) {
     // Change relay state
     if (!message.getBool())  {
        switch (message.sensor)
        {
           case CHILD_ID_LOCK:
              OpenDoor(false);
              break;
           case CHILD_ID_LOCK2:
              OpenDoor2(false);
              break;
        }
     }
  
     // Write some debug info
     Serial.print(F("Lock:  "));
     Serial.print(message.sensor);
     Serial.print(F(" status: "));
     Serial.println(message.getBool());
   }
   else 
   {
     if (message.type == V_ARMED)  {
       // Change relay state
       armed = message.getBool();
  
       // Write some debug info
       Serial.print(F("Arm status: "));
       Serial.println(message.getBool());
     }
     else
     {
       // Write some debug info
       Serial.print(F("Incoming msg type: "));
       Serial.print(message.type);
       Serial.print(F(" id: "));
       Serial.print(message.sensor);
       Serial.print(F(" content: "));
       Serial.println(message.getInt());
     }
   }
}

Chakkie

@BartE

Hi BartE, I have the same issue regarding tags lost after power off. I run the debug instruction using Serial print as you mentioned. I found out that the storeEeprom line did not run after closing the program mode. I think this is why the tags are lost after power cycle.

send: 210-210-0-0 s=255,c=3,t=15,pt=2,l=2,sg=0,st=ok:0
send: 210-210-0-0 s=255,c=0,t=17,pt=0,l=5,sg=0,st=ok:1.5.4
send: 210-210-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
read: 0-0-210 s=255,c=3,t=6,pt=0,l=1,sg=0:M
sensor started, id=210, parent=0, distance=1
send: 210-210-0-0 s=255,c=3,t=11,pt=0,l=9,sg=0,st=ok:RFID Lock
send: 210-210-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.1
send: 210-210-0-0 s=2,c=0,t=19,pt=0,l=0,sg=0,st=ok:
send: 210-210-0-0 s=1,c=0,t=1,pt=0,l=0,sg=0,st=ok:
RecallEeprom
MFRC522 Software Version: 0x92 = v2.0
send: 210-210-0-0 s=1,c=1,t=15,pt=2,l=2,sg=0,st=ok:1
Init done...
Switch 1
Card UID: 26 13 80 41
Invalid card
send: 210-210-0-0 s=1,c=1,t=16,pt=2,l=2,sg=0,st=ok:1
send: 210-210-0-0 s=1,c=1,t=16,pt=2,l=2,sg=0,st=ok:0
release
Card UID: xx xx xx xx
Program mode
release
Card UID: xx xx xx xx
new card
release
Program expired

Thanks

Chakkie

@BartE

I've just solved the issue regarding tags lost after power off.

Simply add the line "StoreEeprom();" after the program mode function

  if (programmode && ((timer % (ONE_SEC / HEARTBEAT)) == 0 ))  {
            ledon = !ledon;
            digitalWrite(LED_PIN, ledon);
            programTimer++;

            // Stop program mode after 20 sec inactivity
            if (programTimer > PROG_WAIT)  {
               programmode = false;
               digitalWrite(LED_PIN, false);
               Serial.println(F("Program expired"));  

               storeEeprom();
               Serial.println(F("Store Card to EEPROM"));  ```

BartE

@Chakkie sorry for the slow response (i was on a pre summer holiday)

Thx for analyzing this report. The fix you did made is not what i meant with program expired.

The idea is that you start program mode by pressing the program button and holding the master card.
And now one can add one or more new RFID cards and when your oke press the program button for a short period to END the program mode and store the new cards.

If you wait too long the program mode will expire and the new cards are NOT stored. Off course you can change this behavior by adding this line as you suggested.

Michel - It

hello to all guys, I noticed some problems, if the power goes away there is a flaw in the system. I modified the source as needed to me, now you turn the sensor on domoticz when you turn on and off when you turn off. I modified the project to create an alarm homemade I configured via lua script the motion sensors. I mounted on the bell so as to turn on and off when I go out or within the home. thank you all

0_1464953864460_mysensor nano+radio+rfid_pcb.jpg

electromaker

Hi Everyone,
I have tested this code http://etabetastudio.blogspot.it/2016/07/tutorial-lettore-rfid-rc522-arduino-idea.html to test RFID RC-522 with Arduino 2009 and all is ok, also to registred RFID card on EEPROM...
I hope to help uo...bye

Mercury69

Dear All,

I'm a newbie and I found in MySensors website the project for RFID Lock Sensors that use PN532 RFID Reader, but as I already have with me a RC-522 RFID reader, searching on the forum I found this post that I thinked it will suit my case.

I assembled the various hardware parts as described on first post, but when I copied the sketch code in my arduino IDE, I'm not able to get it work.

I get some error message that is not so clear for me.

It's seems the sketch is for a previous version of MySensors Library or Arduino IDE, but I'm not sure of this.

As I use Arduino IDE 1.6.12 that has included MySensors Library 2.0.0, is the Sketch you included in the first post already valid for that setup ?

It' will be possible to have a valid sketch working with new setup or eventually to know how to proceed to make the actual one working ?

Thank you in advance for your attention.

Rod MacPherson

@Mercury69
It was written prior to the MySensors 2.0 update.

You can convert pre- 2.0 sketches by following the instructions on https://forum.mysensors.org/topic/4276/converting-a-sketch-from-1-5-x-to-2-0-x

If you need a hand just post here with your question, I'll try to help, but it's really not too bad once you get started. I'm in the process of converting all of my code to 2.0 as well.

Mercury69

@Rod-MacPherson
Dear Rod, thank you for the suggestion you gave me.
Following the instruction you indicated me, I was able to make the sketch working with new MySensors 2.0 library.

Considering that I'm not a programmer, it was quite easy to make the sketch working.

Thank you again for your suggestion and off course thank you to BartE for the good original work he did.

If someone need new sketch working with library 2.0, feel free to ask me.

Michel - It

@Mercury69 you can post the sketch ?

jeti

@Mercury69 I would also love to have a look at your scetch!

miro

@Mercury69

Please, I would also like to see your code if it possible.

cadet

Hi Rod

Can you modify your code for 2.0 lib ?

Thank you
Andrey

RFID Garage door opener

16

11.7k

11.2k

113.1k