Sensor node not working without #define MyDebug

[delinend]

@tekka
BN: Unknown board
VID: 10C4
PID EA60
SN: Upload any sketch to obtain it

Btw. I use OpTiboot loader

[ayo]

So I tried to see if I make one last attempt to fix this problem again, I tried the Alex option using a delay(10) in the for loop. So I put a delay(10) in the for loop of my gateway code whoa it works fully well. I guess their is truly a timely issues here and the enable my_debug it's somehow doing a slowing things down work.
But using a delay(10) in the loop isn't really an efficient way though.
@delinend said:

I have solved it, with the fix from Alex, with a delay(10) in the loop() :-) Thanks

UPDATE: Using a delay(1) also works for me too

[tekka]

@delinend Still not the right thing. Sorry for bugging you with that ;)

You'll find the requested information under:

In Arduino IDE under Tools | Board | Boards Manager => Arduino AVR Boards Built-in by Arduino version 1.6.xx

[delinend]

@tekka
It's: Arduino AVR Board Built-In by Arduino version 1.6.14 installed.

[tekka]

@delinend I've tried your setup but cannot reproduce your issue. Are you on the latest dev branch (from today)? What board did you choose in the settings?

Out of curiosity, please upload this sketch:

#define MY_CORE_ONLY
#define MY_DEBUG
#include <MySensors.h>

void setup() {
  Serial.begin(115200);
  Serial.println("***");
  Serial.print("V=");
  Serial.println(hwCPUVoltage());
  Serial.print("F=");
  Serial.println(hwCPUFrequency());  
  Serial.println("***");
}

void loop() {}

and post the serial output.

[delinend]

Here the output.

---

V=3726
F=89

---

The board name is: [Optiboot] Arduino Pro or Pro Mini (3.3V, 8 MHz) w/ ATmega328
As I use Optiboot bootloader.

##############################################################

pro328o.name=[Optiboot] Arduino Pro or Pro Mini (3.3V, 8 MHz) w/ ATmega328
pro328o.upload.tool=avrdude
pro328o.upload.protocol=arduino
pro328o.upload.maximum_size=32256
pro328o.upload.maximum_data_size=2048
pro328o.upload.speed=57600
pro328o.bootloader.tool=avrdude
pro328o.bootloader.low_fuses=0xff
pro328o.bootloader.high_fuses=0xde
pro328o.bootloader.extended_fuses=0xfd
pro328o.bootloader.file=optiboot/optiboot_atmega328.hex
pro328o.bootloader.unlock_bits=0x3F
pro328o.bootloader.lock_bits=0x0F
pro328o.build.mcu=atmega328p
pro328o.build.board=AVR_PRO
pro328o.build.f_cpu=8000000L
pro328o.build.core=arduino
pro328o.build.variant=eightanaloginputs

##############################################################

[tekka]

@delinend Ok, so you have a slightly higher voltage and frequency - this could cause some timing issues, since the sketch is compiled at 8Mhz. Can you feed 3.3V, e.g. using a voltage regulator?

[delinend]

@tekka
This is with my Lab Powersupply to 3.3V

---

V=3300
F=89

---

[tekka]

@delinend ok, and still the same with MY_DEBUG and the latest dev branch?

[delinend]

@tekka
Hmm.. It works fine without the delay(10), at 3.3V! But if I rice the voltage to around 3.6-3.7V, I have to add the delay(10) again in the void loop(). ?!?!

Btw. The nRF24l01+ is attached Vcc on the Arduino Mini Pro board.