Multi Button Relay Sketch
-
@korttoma your sketch not working for me. I change numer relay to 2 and change pin buttons and relay and not control relay.
@Boots33
Ok i correct your sketch and use:Switch Bistable:
/** DESCRIPTION Sketch for 2x relay with buttons bistable. After back power all relays set OFF and send correct status OFF to controller. */ // Enable debug prints to serial monitor #define MY_DEBUG // Enable and select radio type attached #define MY_RADIO_NRF24 //#define MY_RADIO_RFM69 // Enabled repeater feature for this node #define MY_REPEATER_FEATURE #include <SPI.h> #include <MySensors.h> #include <Bounce2.h> // Define Relays #define RELAY_ON 1 // GPIO value to write to turn on attached relay #define RELAY_OFF 0 // GPIO value to write to turn off attached relay // Define Sensor ID's #define SSR_A_ID 1 // Id of the sensor child #define SSR_B_ID 2 // Id of the sensor child // Define buttons and relays const int buttonPinA = 3; const int buttonPinB = 4; const int relayPinA = 5; const int relayPinB = 6; // Define Variables int oldValueA = 0; int oldValueB = 0; bool stateA = false; bool stateB = false; int trigger = 0; Bounce debouncerA = Bounce(); Bounce debouncerB = Bounce(); MyMessage msgA(SSR_A_ID, V_STATUS); MyMessage msgB(SSR_B_ID, V_STATUS); void setup() { pinMode(buttonPinA, INPUT_PULLUP); // Setup the button Activate internal pull-up pinMode(buttonPinB, INPUT_PULLUP); // Setup the button Activate internal pull-up // After setting up the buttons, setup debouncer debouncerA.attach(buttonPinA); debouncerA.interval(5); debouncerB.attach(buttonPinB); debouncerB.interval(5); // Make sure relays are off when starting up digitalWrite(relayPinA, RELAY_OFF); digitalWrite(relayPinB, RELAY_OFF); // Then set relay pins in output mode pinMode(relayPinA, OUTPUT); pinMode(relayPinB, OUTPUT); /*--------------------- Added these lines for toggle switch-------------------------*/ oldValueA = digitalRead(buttonPinA); // set oldValueA to the current status of the toggle switch oldValueB = digitalRead(buttonPinB); // set oldValueB to the current status of the toggle switch // send(msgA.set(false)); // Send off state for relayA to ensure controller knows the switch is off // send(msgB.set(false)); // Send off state for relayB to ensure controller knows the switch is off } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("2xRelay with bistable", "1.1"); // Register all sensors to gw (they will be created as child devices) present(SSR_A_ID, S_LIGHT); present(SSR_B_ID, S_LIGHT); } /* Example on how to asynchronously check for new messages from gw */ void loop() { if (trigger == 0){ send(msgA.set(false)); // Send off state for relayA to ensure controller knows the switch is off send(msgB.set(false)); // Send off state for relayB to ensure controller knows the switch is off trigger = 1; } debouncerA.update(); // Get the update value int valueA = debouncerA.read(); if (valueA != oldValueA) { // send(msgA.set(stateA ? false : true), true); // Send new state and request ack back send(msgA.set(stateA ? false : true), false); // Send new state with no request for ack stateA = stateA ? false : true; // invert the state digitalWrite(relayPinA, stateA ? RELAY_ON : RELAY_OFF); // toggle the relay oldValueA = valueA; } debouncerB.update(); // Get the update value int valueB = debouncerB.read(); if (valueB != oldValueB) { //send(msgB.set(stateB ? false : true), true); // Send new state and request ack back send(msgB.set(stateB ? false : true), false); // Send new state with no request for ack stateB = stateB ? false : true; // invert the state digitalWrite(relayPinB, stateB ? RELAY_ON : RELAY_OFF); // toggle the relay oldValueB = valueB; } } void receive(const MyMessage &message) { // We only expect one type of message from controller. But we better check anyway. if (message.type == V_STATUS) { switch (message.sensor) { case 1: stateA = message.getBool(); digitalWrite(message.sensor + 4, stateA ? RELAY_ON : RELAY_OFF); break; case 2: stateB = message.getBool(); digitalWrite(message.sensor + 4, stateB ? RELAY_ON : RELAY_OFF); break; } // Write some debug info Serial.print("Incoming change for sensor:"); Serial.println(message.sensor); Serial.print("from node:"); Serial.println(message.sender); Serial.print(", New status: "); Serial.println(message.getBool()); } }Switch monostable:
/** DESCRIPTION Sketch for 2x relay with buttons monostable. After back power all relays set OFF and send correct status OFF to controller. */ // Enable debug prints to serial monitor #define MY_DEBUG // Enable and select radio type attached #define MY_RADIO_NRF24 //#define MY_RADIO_RFM69 // Enabled repeater feature for this node #define MY_REPEATER_FEATURE #include <SPI.h> #include <MySensors.h> #include <Bounce2.h> // Define Relays #define RELAY_ON 1 // GPIO value to write to turn on attached relay #define RELAY_OFF 0 // GPIO value to write to turn off attached relay // Define Sensor ID's #define SSR_A_ID 1 // Id of the sensor child #define SSR_B_ID 2 // Id of the sensor child // Define buttons and relays const int buttonPinA = 3; const int buttonPinB = 4; const int relayPinA = 5; const int relayPinB = 6; // Define Variables int oldValueA = 0; int oldValueB = 0; bool stateA = false; bool stateB = false; int trigger = 0; Bounce debouncerA = Bounce(); Bounce debouncerB = Bounce(); MyMessage msgA(SSR_A_ID, V_STATUS); MyMessage msgB(SSR_B_ID, V_STATUS); void setup() { pinMode(buttonPinA, INPUT_PULLUP); // Setup the button Activate internal pull-up pinMode(buttonPinB, INPUT_PULLUP); // Setup the button Activate internal pull-up // After setting up the buttons, setup debouncer debouncerA.attach(buttonPinA); debouncerA.interval(5); debouncerB.attach(buttonPinB); debouncerB.interval(5); // Make sure relays are off when starting up digitalWrite(relayPinA, RELAY_OFF); digitalWrite(relayPinB, RELAY_OFF); // Then set relay pins in output mode pinMode(relayPinA, OUTPUT); pinMode(relayPinB, OUTPUT); } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("2xRelay with monostable", "1.0"); // Register all sensors to gw (they will be created as child devices) present(SSR_A_ID, S_LIGHT); present(SSR_B_ID, S_LIGHT); } /* Example on how to asynchronously check for new messages from gw */ void loop() { if (trigger == 0){ send(msgA.set(false)); // Send off state for relayA to ensure controller knows the switch is off send(msgB.set(false)); // Send off state for relayB to ensure controller knows the switch is off trigger = 1; } debouncerA.update(); // Get the update value int valueA = debouncerA.read(); if (valueA != oldValueA && valueA == 0) { send(msgA.set(stateA ? false : true), true); // Send new state and request ack back } oldValueA = valueA; debouncerB.update(); // Get the update value int valueB = debouncerB.read(); if (valueB != oldValueB && valueB == 0) { send(msgB.set(stateB ? false : true), true); // Send new state and request ack back } oldValueB = valueB; } void receive(const MyMessage &message) { // We only expect one type of message from controller. But we better check anyway. if (message.type == V_STATUS) { switch (message.sensor) { case 1: stateA = message.getBool(); digitalWrite(message.sensor + 4, stateA ? RELAY_ON : RELAY_OFF); break; case 2: stateB = message.getBool(); digitalWrite(message.sensor + 4, stateB ? RELAY_ON : RELAY_OFF); break; } // Write some debug info Serial.print("Incoming change for sensor:"); Serial.println(message.sensor); Serial.print("from node:"); Serial.println(message.sender); Serial.print(", New status: "); Serial.println(message.getBool()); } }On this sketches it works ok. After power down and then power back all relays go to OFF and correct send info to Gateway and Domoticz that relays is OFF. But when Gateway is available.
But problem is when GATEWAY is not awailable when power for node come back.
If before lost power relay is ON and then power lost , and gateway is lost, and then power back to Node it goes to OFF all relay. It is ok.But when Gateway come back and now is available still show in Domoticz that relay is ON(on begin was ON). But Node should update status info after Gateway come back and is now available. But no update and show in Domoticz latest status.It is very need and then this sketches will be the best for lights :)
When power lost and then come back, Node with sketches faster start then start Raspberry with Domoticz and connect Gateway Serial MySensors. An in this situation status is not update in Gateway/Domoticz.
Please help us. please
-
@Boots33
ack is important , so we can not found any solution for this ? for exapmle add a code to this sketch , that when radio is disconnect so without ack work and when radio is ok this way stop and with ack work again.
this idea is for when a radio have problem or fail or other reason... so this light or other divece dont stop working and work handy when radio go to correct or change radio....if you can change your code and add this option , so your sketch is best code for light control
@rayan said:
@Boots33
ack is important , so we can not found any solution for this ? for exapmle add a code to this sketch , that when radio is disconnect so without ack work and when radio is ok this way stop and with ack work again.
this idea is for when a radio have problem or fail or other reason... so this light or other divece dont stop working and work handy when radio go to correct or change radio....if you can change your code and add this option , so your sketch is best code for light control
There have been a few threads about the issue of nodes not running the loop part of the sketch if a connection to the gateway cannot be established. Have a look Here and Here for a bit more info. It is a feature I am sure many would like to see in the next version of MySensors. For the moment MySensors does not support 100% what you want to do.
If you want to combine the two versions of the sketches you will need to have a method to check whether a connection to the gateway is present. You could try something like this in the loop.
if (isTransportOK()){ // put code to execute when connection is available here } else { // put code to execute when no connection is available here }You will be adding a fair bit of complexity to the sketch. Can you tell me why the ACK is so important for you.
-
What is ACK ?
And can you show me all code with your if transport is ok to send update status to gateway...but if transport is wrong example try send every 1 minut and stop when send is good.
I am begginner sorry
Did you know any info that this function will be implement in next version as you write in latest your post ?
-
@rayan said:
@Boots33
ack is important , so we can not found any solution for this ? for exapmle add a code to this sketch , that when radio is disconnect so without ack work and when radio is ok this way stop and with ack work again.
this idea is for when a radio have problem or fail or other reason... so this light or other divece dont stop working and work handy when radio go to correct or change radio....if you can change your code and add this option , so your sketch is best code for light control
There have been a few threads about the issue of nodes not running the loop part of the sketch if a connection to the gateway cannot be established. Have a look Here and Here for a bit more info. It is a feature I am sure many would like to see in the next version of MySensors. For the moment MySensors does not support 100% what you want to do.
If you want to combine the two versions of the sketches you will need to have a method to check whether a connection to the gateway is present. You could try something like this in the loop.
if (isTransportOK()){ // put code to execute when connection is available here } else { // put code to execute when no connection is available here }You will be adding a fair bit of complexity to the sketch. Can you tell me why the ACK is so important for you.
@Boots33
ack is a feedback . is this true ? so when i am out of home and i want turn on light , so ack show me that light is on or no ! also when there is a problem in connection and ack dont receive, so node search and found a new way for connection.
now i dont have a arduino and radio for test :) but do you think this code will be ok ?without else.void loop() { if (!isTransportOK()) { if (...) //if change switch to up or down ... //change state of relay if(isTransportOK()) send(msg.set(state ? true : false), true); // (last state) } debouncer.update(); // Get the update value int value = debouncer.read(); if (value != oldValue && value == 0) { send(msg.set(state ? false : true), true); // Send new state and request ack back } oldValue = value; }(i can not work with Bounce2 library :) ) please help to fill lines
in loop we add a "if (!isTransportOK())" and write when change switch (on/off) state of relay change and this is repeat until connection will be ok ! so send a ack and for continue follow your code...
is this right ? can you do this change ? -
Hi
I can test it but i must have finall code because i dont know what code i must put in (...). I am begginer user and i dont know how write programming. -
Ok but can you give me ready code which i must put in code to my relays and then i test it.
-
Guys I feel this thread has wandered a long way from the original topic and has taken up a lot of time. i really don't think there is a lot to be gained by turning the fairly simple relay sketch into what you now desire.
Even with the changes it still will not work if it boots up and can't find the gateway.
I am posting a final sketch which you may like to try, again it is untested so you may still need to work on it. I hope you understand I have a few of my own uncompleted projects that I want to get back to with the limited free time I have. Good luck with your MySensors journey.
#define MY_DEBUG #define MY_RADIO_NRF24 #define MY_REPEATER_FEATURE #include <SPI.h> #include <MySensors.h> #include <Bounce2.h> #define RELAY_ON 1 #define RELAY_OFF 0 #define SSR_A_ID 1 // Id of the sensor child #define SSR_B_ID 2 // Id of the sensor child const int buttonPinA = 18; const int buttonPinB = 19; const int relayPinA = 5; const int relayPinB = 6; int oldValueA = 0; int oldValueB = 0; bool stateA = false; bool stateB = false; int trigger = 0; Bounce debouncerA = Bounce(); Bounce debouncerB = Bounce(); MyMessage msgA(SSR_A_ID, V_STATUS); MyMessage msgB(SSR_B_ID, V_STATUS); void setup() { pinMode(buttonPinA, INPUT_PULLUP); // Setup the button Activate internal pull-up pinMode(buttonPinB, INPUT_PULLUP); // Setup the button Activate internal pull-up // Then set relay pins in output mode pinMode(relayPinA, OUTPUT); pinMode(relayPinB, OUTPUT); // After setting up the buttons, setup debouncer debouncerA.attach(buttonPinA); debouncerA.interval(5); debouncerB.attach(buttonPinB); debouncerB.interval(5); // Make sure relays are off when starting up digitalWrite(relayPinA, RELAY_OFF); digitalWrite(relayPinB, RELAY_OFF); /*--------------------- Added these lines for toggle switch-------------------------*/ oldValueA = digitalRead(buttonPinA); // set oldValueA to the current status of the toggle switch oldValueB = digitalRead(buttonPinB); // set oldValueB to the current status of the toggle switch // send(msgA.set(false)); // Send off state for relayA to ensure controller knows the switch is off // send(msgB.set(false)); // Send off state for relayB to ensure controller knows the switch is off } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("Mains Controller", "1.0"); // Register all sensors to gw (they will be created as child devices) present(SSR_A_ID, S_LIGHT); present(SSR_B_ID, S_LIGHT); } /* Example on how to asynchronously check for new messages from gw */ void loop() { if (trigger == 0){ send(msgA.set(false)); // Send off state for relayA to ensure controller knows the switch is off send(msgB.set(false)); // Send off state for relayB to ensure controller knows the switch is off trigger = 1; } if (isTransportOK()){ // put code to execute when connection is available here connectionPresent(); } else { // put code to execute when no connection is available here connectionLost(); } } void receive(const MyMessage &message) { // We only expect one type of message from controller. But we better check anyway. if (message.type == V_STATUS) { switch (message.sensor) { case 1: stateA = message.getBool(); digitalWrite(message.sensor + 4, stateA ? RELAY_ON : RELAY_OFF); break; case 2: stateB = message.getBool(); digitalWrite(message.sensor + 4, stateB ? RELAY_ON : RELAY_OFF); break; } // Write some debug info Serial.print("Incoming change for sensor:"); Serial.println(message.sensor); Serial.print("from node:"); Serial.println(message.sender); Serial.print(", New status: "); Serial.println(message.getBool()); } } void connectionPresent() { // put code to execute when connection is available here debouncerA.update(); // Get the update value int valueA = debouncerA.read(); if (valueA != oldValueA) { send(msgA.set(stateA ? false : true), true); // Send new state and request ack back oldValueA = valueA; } debouncerB.update(); // Get the update value int valueB = debouncerB.read(); if (valueB != oldValueB) { send(msgB.set(stateB ? false : true), true); // Send new state and request ack back oldValueB = valueB; } } void connectionLost() { // put code to execute when no connection is available here debouncerA.update(); // Get the update value int valueA = debouncerA.read(); if (valueA != oldValueA) { // send(msgA.set(stateA ? false : true), true); // Send new state and request ack back send(msgA.set(stateA ? false : true), false); // Send new state with no request for ack stateA = stateA ? false : true; // invert the state digitalWrite(relayPinA, stateA ? RELAY_ON : RELAY_OFF); // toggle the relay oldValueA = valueA; } debouncerB.update(); // Get the update value int valueB = debouncerB.read(); if (valueB != oldValueB) { //send(msgB.set(stateB ? false : true), true); // Send new state and request ack back send(msgB.set(stateB ? false : true), false); // Send new state with no request for ack stateB = stateB ? false : true; // invert the state digitalWrite(relayPinB, stateB ? RELAY_ON : RELAY_OFF); // toggle the relay oldValueB = valueB; } } -
Guys I feel this thread has wandered a long way from the original topic and has taken up a lot of time. i really don't think there is a lot to be gained by turning the fairly simple relay sketch into what you now desire.
Even with the changes it still will not work if it boots up and can't find the gateway.
I am posting a final sketch which you may like to try, again it is untested so you may still need to work on it. I hope you understand I have a few of my own uncompleted projects that I want to get back to with the limited free time I have. Good luck with your MySensors journey.
#define MY_DEBUG #define MY_RADIO_NRF24 #define MY_REPEATER_FEATURE #include <SPI.h> #include <MySensors.h> #include <Bounce2.h> #define RELAY_ON 1 #define RELAY_OFF 0 #define SSR_A_ID 1 // Id of the sensor child #define SSR_B_ID 2 // Id of the sensor child const int buttonPinA = 18; const int buttonPinB = 19; const int relayPinA = 5; const int relayPinB = 6; int oldValueA = 0; int oldValueB = 0; bool stateA = false; bool stateB = false; int trigger = 0; Bounce debouncerA = Bounce(); Bounce debouncerB = Bounce(); MyMessage msgA(SSR_A_ID, V_STATUS); MyMessage msgB(SSR_B_ID, V_STATUS); void setup() { pinMode(buttonPinA, INPUT_PULLUP); // Setup the button Activate internal pull-up pinMode(buttonPinB, INPUT_PULLUP); // Setup the button Activate internal pull-up // Then set relay pins in output mode pinMode(relayPinA, OUTPUT); pinMode(relayPinB, OUTPUT); // After setting up the buttons, setup debouncer debouncerA.attach(buttonPinA); debouncerA.interval(5); debouncerB.attach(buttonPinB); debouncerB.interval(5); // Make sure relays are off when starting up digitalWrite(relayPinA, RELAY_OFF); digitalWrite(relayPinB, RELAY_OFF); /*--------------------- Added these lines for toggle switch-------------------------*/ oldValueA = digitalRead(buttonPinA); // set oldValueA to the current status of the toggle switch oldValueB = digitalRead(buttonPinB); // set oldValueB to the current status of the toggle switch // send(msgA.set(false)); // Send off state for relayA to ensure controller knows the switch is off // send(msgB.set(false)); // Send off state for relayB to ensure controller knows the switch is off } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("Mains Controller", "1.0"); // Register all sensors to gw (they will be created as child devices) present(SSR_A_ID, S_LIGHT); present(SSR_B_ID, S_LIGHT); } /* Example on how to asynchronously check for new messages from gw */ void loop() { if (trigger == 0){ send(msgA.set(false)); // Send off state for relayA to ensure controller knows the switch is off send(msgB.set(false)); // Send off state for relayB to ensure controller knows the switch is off trigger = 1; } if (isTransportOK()){ // put code to execute when connection is available here connectionPresent(); } else { // put code to execute when no connection is available here connectionLost(); } } void receive(const MyMessage &message) { // We only expect one type of message from controller. But we better check anyway. if (message.type == V_STATUS) { switch (message.sensor) { case 1: stateA = message.getBool(); digitalWrite(message.sensor + 4, stateA ? RELAY_ON : RELAY_OFF); break; case 2: stateB = message.getBool(); digitalWrite(message.sensor + 4, stateB ? RELAY_ON : RELAY_OFF); break; } // Write some debug info Serial.print("Incoming change for sensor:"); Serial.println(message.sensor); Serial.print("from node:"); Serial.println(message.sender); Serial.print(", New status: "); Serial.println(message.getBool()); } } void connectionPresent() { // put code to execute when connection is available here debouncerA.update(); // Get the update value int valueA = debouncerA.read(); if (valueA != oldValueA) { send(msgA.set(stateA ? false : true), true); // Send new state and request ack back oldValueA = valueA; } debouncerB.update(); // Get the update value int valueB = debouncerB.read(); if (valueB != oldValueB) { send(msgB.set(stateB ? false : true), true); // Send new state and request ack back oldValueB = valueB; } } void connectionLost() { // put code to execute when no connection is available here debouncerA.update(); // Get the update value int valueA = debouncerA.read(); if (valueA != oldValueA) { // send(msgA.set(stateA ? false : true), true); // Send new state and request ack back send(msgA.set(stateA ? false : true), false); // Send new state with no request for ack stateA = stateA ? false : true; // invert the state digitalWrite(relayPinA, stateA ? RELAY_ON : RELAY_OFF); // toggle the relay oldValueA = valueA; } debouncerB.update(); // Get the update value int valueB = debouncerB.read(); if (valueB != oldValueB) { //send(msgB.set(stateB ? false : true), true); // Send new state and request ack back send(msgB.set(stateB ? false : true), false); // Send new state with no request for ack stateB = stateB ? false : true; // invert the state digitalWrite(relayPinB, stateB ? RELAY_ON : RELAY_OFF); // toggle the relay oldValueB = valueB; } } -
Guys I feel this thread has wandered a long way from the original topic and has taken up a lot of time. i really don't think there is a lot to be gained by turning the fairly simple relay sketch into what you now desire.
Even with the changes it still will not work if it boots up and can't find the gateway.
I am posting a final sketch which you may like to try, again it is untested so you may still need to work on it. I hope you understand I have a few of my own uncompleted projects that I want to get back to with the limited free time I have. Good luck with your MySensors journey.
#define MY_DEBUG #define MY_RADIO_NRF24 #define MY_REPEATER_FEATURE #include <SPI.h> #include <MySensors.h> #include <Bounce2.h> #define RELAY_ON 1 #define RELAY_OFF 0 #define SSR_A_ID 1 // Id of the sensor child #define SSR_B_ID 2 // Id of the sensor child const int buttonPinA = 18; const int buttonPinB = 19; const int relayPinA = 5; const int relayPinB = 6; int oldValueA = 0; int oldValueB = 0; bool stateA = false; bool stateB = false; int trigger = 0; Bounce debouncerA = Bounce(); Bounce debouncerB = Bounce(); MyMessage msgA(SSR_A_ID, V_STATUS); MyMessage msgB(SSR_B_ID, V_STATUS); void setup() { pinMode(buttonPinA, INPUT_PULLUP); // Setup the button Activate internal pull-up pinMode(buttonPinB, INPUT_PULLUP); // Setup the button Activate internal pull-up // Then set relay pins in output mode pinMode(relayPinA, OUTPUT); pinMode(relayPinB, OUTPUT); // After setting up the buttons, setup debouncer debouncerA.attach(buttonPinA); debouncerA.interval(5); debouncerB.attach(buttonPinB); debouncerB.interval(5); // Make sure relays are off when starting up digitalWrite(relayPinA, RELAY_OFF); digitalWrite(relayPinB, RELAY_OFF); /*--------------------- Added these lines for toggle switch-------------------------*/ oldValueA = digitalRead(buttonPinA); // set oldValueA to the current status of the toggle switch oldValueB = digitalRead(buttonPinB); // set oldValueB to the current status of the toggle switch // send(msgA.set(false)); // Send off state for relayA to ensure controller knows the switch is off // send(msgB.set(false)); // Send off state for relayB to ensure controller knows the switch is off } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("Mains Controller", "1.0"); // Register all sensors to gw (they will be created as child devices) present(SSR_A_ID, S_LIGHT); present(SSR_B_ID, S_LIGHT); } /* Example on how to asynchronously check for new messages from gw */ void loop() { if (trigger == 0){ send(msgA.set(false)); // Send off state for relayA to ensure controller knows the switch is off send(msgB.set(false)); // Send off state for relayB to ensure controller knows the switch is off trigger = 1; } if (isTransportOK()){ // put code to execute when connection is available here connectionPresent(); } else { // put code to execute when no connection is available here connectionLost(); } } void receive(const MyMessage &message) { // We only expect one type of message from controller. But we better check anyway. if (message.type == V_STATUS) { switch (message.sensor) { case 1: stateA = message.getBool(); digitalWrite(message.sensor + 4, stateA ? RELAY_ON : RELAY_OFF); break; case 2: stateB = message.getBool(); digitalWrite(message.sensor + 4, stateB ? RELAY_ON : RELAY_OFF); break; } // Write some debug info Serial.print("Incoming change for sensor:"); Serial.println(message.sensor); Serial.print("from node:"); Serial.println(message.sender); Serial.print(", New status: "); Serial.println(message.getBool()); } } void connectionPresent() { // put code to execute when connection is available here debouncerA.update(); // Get the update value int valueA = debouncerA.read(); if (valueA != oldValueA) { send(msgA.set(stateA ? false : true), true); // Send new state and request ack back oldValueA = valueA; } debouncerB.update(); // Get the update value int valueB = debouncerB.read(); if (valueB != oldValueB) { send(msgB.set(stateB ? false : true), true); // Send new state and request ack back oldValueB = valueB; } } void connectionLost() { // put code to execute when no connection is available here debouncerA.update(); // Get the update value int valueA = debouncerA.read(); if (valueA != oldValueA) { // send(msgA.set(stateA ? false : true), true); // Send new state and request ack back send(msgA.set(stateA ? false : true), false); // Send new state with no request for ack stateA = stateA ? false : true; // invert the state digitalWrite(relayPinA, stateA ? RELAY_ON : RELAY_OFF); // toggle the relay oldValueA = valueA; } debouncerB.update(); // Get the update value int valueB = debouncerB.read(); if (valueB != oldValueB) { //send(msgB.set(stateB ? false : true), true); // Send new state and request ack back send(msgB.set(stateB ? false : true), false); // Send new state with no request for ack stateB = stateB ? false : true; // invert the state digitalWrite(relayPinB, stateB ? RELAY_ON : RELAY_OFF); // toggle the relay oldValueB = valueB; } }@Boots33
hi my friend.
i use your sketch and thank you.but there is a problem.
sketchs in site , when relay is fail , when i send command , so show to me "Error sending switch command, check device/hardware !" but your sketch dont show this error. so i dont understand relay is fail or no , when we are out home. can you fix this ? -
Here is an example that I'm using with 4 relays and 4 monostable buttons:
// Enable debug prints to serial monitor #define MY_DEBUG // Enable and select radio type attached #define MY_RADIO_NRF24 #define SN "RelayButtonArray" #define SV "1.0" #include <MySensors.h> #include <SPI.h> #include <Bounce2.h> #define RELAY_ON 0 // switch around for ACTIVE LOW / ACTIVE HIGH relay #define RELAY_OFF 1 // #define noRelays 4 //2-4 const int relayPin[] = {14, 15, 16, 17}; // switch around pins to your desire const int buttonPin[] = {6, 7, 4, 5}; // switch around pins to your desire class Relay // relay class, store all relevant data (equivalent to struct) { public: int buttonPin; // physical pin number of button int relayPin; // physical pin number of relay boolean relayState; // relay status (also stored in EEPROM) }; Relay Relays[noRelays]; Bounce debouncer[noRelays]; MyMessage msg[noRelays]; /* void before() { for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) { // Then set relay pins in output mode pinMode(pin, OUTPUT); // Set relay to last known state (using eeprom storage) digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF); } }*/ void setup() { wait(100); // Initialize Relays with corresponding buttons for (int i = 0; i < noRelays; i++) { Relays[i].buttonPin = buttonPin[i]; // assign physical pins Relays[i].relayPin = relayPin[i]; msg[i].sensor = i; // initialize messages msg[i].type = V_LIGHT; pinMode(Relays[i].buttonPin, INPUT_PULLUP); wait(100); pinMode(Relays[i].relayPin, OUTPUT); Relays[i].relayState = loadState(i); // retrieve last values from EEPROM digitalWrite(Relays[i].relayPin, Relays[i].relayState ? RELAY_ON : RELAY_OFF); // and set relays accordingly send(msg[i].set(Relays[i].relayState ? true : false)); // make controller aware of last status wait(50); debouncer[i] = Bounce(); // initialize debouncer debouncer[i].attach(buttonPin[i]); debouncer[i].interval(30); wait(50); } } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo(SN, SV); wait(100); for (int i = 0; i < noRelays; i++) present(i, S_LIGHT); // present sensor to gateway wait(100); } void loop() { for (byte i = 0; i < noRelays; i++) { if (debouncer[i].update()) { int value = debouncer[i].read(); if ( value == LOW) { Relays[i].relayState = !Relays[i].relayState; digitalWrite(Relays[i].relayPin, Relays[i].relayState ? RELAY_ON : RELAY_OFF); send(msg[i].set(Relays[i].relayState ? true : false)); // save sensor state in EEPROM (location == sensor number) saveState( i, Relays[i].relayState ); } } } //wait(20); } void receive(const MyMessage &message) { if (message.type == V_LIGHT) { if (message.sensor < noRelays) { // check if message is valid for relays..... previous line [[[ if (message.sensor <=noRelays){ ]]] Relays[message.sensor].relayState = message.getBool(); digitalWrite(Relays[message.sensor].relayPin, Relays[message.sensor].relayState ? RELAY_ON : RELAY_OFF); // and set relays accordingly saveState( message.sensor, Relays[message.sensor].relayState ); // save sensor state in EEPROM (location == sensor number) } } wait(20); }@korttoma love this sketch. Used it for a dual LED strip light controller for our loft where our kids sleep - daughter on one side and boys on the other, both with LED strips (RGB) i installed. This way we can turn them on or off remotely without having to climb up there!!
Worked great. Thankyou for sharing.
-
Anybody has a sketch where multiple buttons are put up on single wire and voltage drop is used to distinguish between them?
-
Hi
Has anybody solution how resolved problem update status when connection with gateway is not available and then come back connection with gateway?@pepson have a look at this Synchronising Light switch
-
I try sketch from your link but i test and the same issu.
I enable relay, then disable GATEWAY MySensors on DOmoticz and then change status relay to DISABLE by button. Then enable Gateway on Domoticz and still in domoticz show that relay is ENABLED. Not update status that i manual DISABLE relay by button.
