Serial Gateway Sketch with si7021

Markus.

can it work like this?

// Enable debug prints to serial monitor
#define MY_DEBUG


// Enable and select radio type attached
#define MY_RADIO_RFM69
#define MY_RFM69_FREQUENCY RFM69_868MHZ

#include <Wire.h>
#include <SI7021.h>
#include <SPI.h>
#include <RunningAverage.h>


#ifdef MY_DEBUG
#define DEBUG_SERIAL(x) Serial.begin(x)
#define DEBUG_PRINT(x) Serial.print(x)
#define DEBUG_PRINTLN(x) Serial.println(x)
#else
#define DEBUG_SERIAL(x)
#define DEBUG_PRINT(x) 
#define DEBUG_PRINTLN(x) 
#endif

#define CHILD_ID_TEMP 0
#define CHILD_ID_HUM 1
// #define SLEEP_TIME 15000 // 15s for DEBUG
#define SLEEP_TIME 300000   // 5 min
#define FORCE_TRANSMIT_CYCLE 36  // 5min*12=1/hour, 5min*36=1/3hour 
#define HUMI_TRANSMIT_THRESHOLD 3.0  // THRESHOLD tells how much the value should have changed since last time it was transmitted.
#define TEMP_TRANSMIT_THRESHOLD 0.5
#define AVERAGES 2

int measureCount = 0;
float lastTemperature = -100;
int lastHumidity = -100;

RunningAverage raHum(AVERAGES);
SI7021 humiditySensor;


// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE

// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE

// Flash leds on rx/tx/err
// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED

#include <MySensors.h>

MyMessage msgTemp(CHILD_ID_TEMP,V_TEMP); // Initialize temperature message
MyMessage msgHum(CHILD_ID_HUM,V_HUM);


void setup()
{
  DEBUG_SERIAL(38400);    // <<<<<<<<<<<<<<<<<<<<<<<<<< Note BAUD_RATE in MySensors.h
  DEBUG_PRINTLN("Serial started");
  delay(500); // Allow time for radio if power useed as reset
  DEBUG_PRINT("Node and "); DEBUG_PRINTLN("2 children presented.");
   raHum.clear();
  
}

void presentation()
{ 
  sendSketchInfo("Gateway_SI7021", "1.0 161017");
  present(CHILD_ID_TEMP, S_TEMP);   // Present sensor to controller
  present(CHILD_ID_HUM, S_HUM);
}


void loop()
{ 

  measureCount ++;
  bool forceTransmit = false;
  
  if (measureCount > FORCE_TRANSMIT_CYCLE) {
    forceTransmit = true; 
  }
  sendTempHumidityMeasurements(forceTransmit);
/*
  // Read and print internal temp
  float temperature0 = static_cast<float>(static_cast<int>((GetInternalTemp()+0.5) * 10.)) / 10.;
  DEBUG_PRINT("Internal Temp: "); DEBUG_PRINT(temperature0); DEBUG_PRINTLN(" *C");        
*/
 
  sleep(SLEEP_TIME);
}

/*********************************************
 * * Sends temperature and humidity from Si7021 sensor
 * Parameters
 * - force : Forces transmission of a value (even if it's the same as previous measurement)
 *********************************************/
void sendTempHumidityMeasurements(bool force) {
  bool tx = force;

  si7021_env data = humiditySensor.getHumidityAndTemperature();
  
  float temperature = data.celsiusHundredths / 100.0;
  DEBUG_PRINT("T: ");DEBUG_PRINTLN(temperature);
  float diffTemp = abs(lastTemperature - temperature);
  DEBUG_PRINT(F("TempDiff :"));DEBUG_PRINTLN(diffTemp);
  if (diffTemp > TEMP_TRANSMIT_THRESHOLD || tx) {
    send(msgTemp.set(temperature,1));
    lastTemperature = temperature;
    measureCount = 0;
    DEBUG_PRINTLN("T sent!");
  }
  
  int humidity = data.humidityPercent;
  DEBUG_PRINT("H: ");DEBUG_PRINTLN(humidity);
  raHum.addValue(humidity);
  humidity = raHum.getAverage();  // MA sample imply reasonable fast sample frequency
  float diffHum = abs(lastHumidity - humidity);  
  DEBUG_PRINT(F("HumDiff  :"));DEBUG_PRINTLN(diffHum); 
  if (diffHum > HUMI_TRANSMIT_THRESHOLD || tx) {
    send(msgHum.set(humidity));
    lastHumidity = humidity;
    measureCount = 0;
    DEBUG_PRINTLN("H sent!");
  }

}

gohan

Did you try it?

Markus.

not yet ;-) Will try it later....

Markus.

tried now the Sketch... Seems that something is wrong with the sensor.

 __  __       ____
|  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
| |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
| |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
|_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
        |___/                      2.2.0-beta

0;255;3;0;9;53 MCO:BGN:INIT GW,CP=RRNGA---,VER=2.2.0-beta
0;255;3;0;9;83 TSM:INIT
0;255;3;0;9;92 TSF:WUR:MS=0
0;255;3;0;9;100 TSM:INIT:TSP OK
0;255;3;0;9;108 TSM:INIT:GW MODE
0;255;3;0;9;118 TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;129 MCO:REG:NOT NEEDED
0;255;3;0;14;Gateway startup complete.
0;255;0;0;18;2.2.0-beta
0;255;3;0;11;Gateway_SI7021
0;255;3;0;12;1.0 161017
0;0;0;0;6;
0;1;0;0;7;
0;255;3;0;9;159 MCO:BGN:STP
Serial started
Node and 2 children presented.
0;255;3;0;9;684 MCO:BGN:INIT OK,TSP=1

Also the issue with the attached sensor blocks completly the Gateway function.Means that the Gateway didn't receive anything. Is it possible to prevent such issue? what I mean, is it possible to seperate both functions in the Sketch in that way If something is wrong with the sensor, the Gateway can still operate?
THX
Markus

gohan

add some more serial prints around to see where the code stops

Markus.

@gohan how can i do this ? :-(

gohan

Look at the "DEBUG_PRINTLN" you have in your code, add some of those where you see there aren't.

Markus.

the Code stops here

si7021_env data = humiditySensor.getHumidityAndTemperature();

Anything wrong with the sensor I guess. But how can I handle such things?

gohan

did you try an example sketch from the library to see if you can read the values correctly?

Markus.

the sensor conenction was the Problem at the end. Changed SCD and SCL and now it Looks good so far. At the Moment is the Gateway not connected to a Controller. Hope the sensor will be then also send the values...

 __  __       ____
|  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
| |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
| |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
|_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
        |___/                      2.2.0-beta

0;255;3;0;9;53 MCO:BGN:INIT GW,CP=RRNGA---,VER=2.2.0-beta
0;255;3;0;9;83 TSM:INIT
0;255;3;0;9;92 TSF:WUR:MS=0
0;255;3;0;9;100 TSM:INIT:TSP OK
0;255;3;0;9;108 TSM:INIT:GW MODE
0;255;3;0;9;118 TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;129 MCO:REG:NOT NEEDED
0;255;3;0;14;Gateway startup complete.
0;255;0;0;18;2.2.0-beta
0;255;3;0;11;Gateway_SI7021
0;255;3;0;12;1.0 161017
0;0;0;0;6;
0;1;0;0;7;
0;255;3;0;9;159 MCO:BGN:STP
Serial started
Node and 2 children presented.
0;255;3;0;9;684 MCO:BGN:INIT OK,TSP=1
Loop1 started
T: 21.49
TempDiff :121.49
0;0;1;0;0;21.5
T sent!
H: 64
HumDiff  :164.00
0;1;1;0;1;64
H sent!
Before first sleep
0;255;3;0;9;733 MCO:SLP:MS=300000,SMS=0,I1=255,M1=255,I2=255,M2=255
0;255;3;0;9;768 !MCO:SLP:REP
0;255;3;0;9;124672 TSF:MSG:READ,106-106-0,s=0,c=1,t=1,pt=7,l=5,sg=0:63.3
106;0;1;0;1;63.3
0;255;3;0;9;124702 TSF:MSG:READ,106-106-0,s=255,c=3,t=0,pt=1,l=1,sg=0:90
106;255;3;0;0;90
0;255;3;0;9;124735 TSF:MSG:READ,106-106-0,s=3,c=1,t=38,pt=7,l=5,sg=0:3.71
106;3;1;0;38;3.71
After first sleep
Loop1 started
T: 21.64
TempDiff :0.15
H: 65
HumDiff  :0.00
Before first sleep
0;255;3;0;9;300797 MCO:SLP:MS=300000,SMS=0,I1=255,M1=255,I2=255,M2=255
0;255;3;0;9;300830 !MCO:SLP:REP
0;255;3;0;9;428443 TSF:MSG:READ,106-106-0,s=255,c=3,t=0,pt=1,l=1,sg=0:90
106;255;3;0;0;90
0;255;3;0;9;428476 TSF:MSG:READ,106-106-0,s=3,c=1,t=38,pt=7,l=5,sg=0:3.72
106;3;1;0;38;3.72

But how can I prevent the Situation that a defect or missing sensor on the Gateway blocks also the Gateway function ?

Thanks

Markus

gohan

You need to make a check in the code that if the sensor read is fails it should keep going

Markus.

@gohan ;-) will try it.... -> Learning leasson... :-)

Serial Gateway Sketch with si7021

17

12.0k

11.2k

113.4k