💬 Building a Raspberry Pi Gateway

ricorico94

Thanks a lot for your clear explanations ! Very useful !
and.. bravo ! for all your work

ricorico94

Hi,
I'm trying to install the gateway on a Raspberry Pi 2 hosting Domoticz already (I had used the standard Domoticz image).
I receive an error message on the make step, but maybe I've not properly understood instructions (not very friendly with raspberry and linux environment).
First, I wired the NRF24 with PA (meaning I used an adapter and the 5V physical PIN#4) and the IRQ (wired on physical pin #15)
Then I logged into my raspberry and staid in initial directory (pi@raspberrypi )
I then typed:

pi@raspberrypi ~ $ git clone https://github.com/mysensors/MySensors.git --branch master
Cloning into 'MySensors'...
remote: Counting objects: 14895, done.
remote: Compressing objects: 100% (8/8), done.
remote: Total 14895 (delta 0), reused 5 (delta 0), pack-reused 14887
Receiving objects: 100% (14895/14895), 12.17 MiB | 1.68 MiB/s, done.
Resolving deltas: 100% (9022/9022), done.
pi@raspberrypi ~ $ cd MySensors
pi@raspberrypi ~/MySensors $ ./configure --help

Hopefully I did it in adequate folder ? (now I see a Mysensors folder in my /home/pi folder).
Then I typed:

pi@raspberrypi ~/MySensors $ --my-transport=nrf24
-bash: --my-transport=nrf24 : commande introuvable
pi@raspberrypi ~/MySensors $ ./configure --my-transport=nrf24
[SECTION] Detecting target machine.
  [OK] machine detected: SoC=BCM2836, Type=Rpi2, CPU=armv7l.
[SECTION] Detecting SPI driver.
  [OK] SPI driver detected:BCM.
[SECTION] Detecting init system.
  [OK] init system detected: sysvinit.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.

So far, no error.. but should I have typed "./configure --my-transport=nrf24 --my-rf24-irq-pin=15" to implement the IRQ ? If yes, can I retype that command with new settings without issue ?

Then I understaood I had to run make command:

pi@raspberrypi ~/MySensors $ make
gcc -MT build/drivers/Linux/log.o -MMD -MP -march=armv7-a -mtune=cortex-a7 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/RPi -I./drivers/BCM -c drivers/Linux/log.c -o build/drivers/Linux/log.o
cc1: error: bad value (cortex-a7) for -mtune switch
Makefile:118: recipe for target 'build/drivers/Linux/log.o' failed
make: *** [build/drivers/Linux/log.o] Error 1

But errors...
I tried to search on forum, and saw someone else meniotning a smilar error, but people were answering about OrangePI, whereas I use a Rasp PI 2.
I probably misunderstood some steps.. Could someone help me ?

Note: in instructions, there's a statement I don't understand for ethernet gateway: "To set the gateway as a client that connects to a controller, use:--my-gateway=ethernet --my-controller-url-address=YOUR-CONTROLLER-ADDRES" . IN which case do we need that ? (as said, I plan to simply use this gateway on My dodmoticz rasp PI).

br,
Ricorico94

gohan

@ricorico94 said in Building a Raspberry Pi Gateway:

./configure --my-transport=nrf24 --my-rf24-irq-pin=15

That is fine, no need to add extra parameters as by defaults it will configure as ethernet gateway. Also try using the development branch as it has lots of bugs fixed.

arraWX

@ricorico94 Yesterday I managed to make a working rpi gateway. I am on rpi3, use a socket adapter board for the radio and use domoticz. I posted all the details here: https://forum.mysensors.org/topic/7793/nrf24l01-problems-in-2-1-1-and-2-2-0-beta/24

ricorico94

Hi,
@arraWX : I looked at your post. Unfortunately, the error I face is before the start, as it's during the make, so it appears I follow the first steps you describe (config & make), but I still don't know how to solve the make errors.

In case it can help understanding what's going on or what to do, I ran the command:

gcc -v

which displayed: gcc version 4.6.3 (Debian 4.6.3-14+rpi1)
Could it be an issue this "+rpi1" whreas I've a PI 2 ?

arraWX

Do not know if it is of any help, but mine says: gcc version 4.9.2 (Raspbian 4.9.2-10)

ricorico94

Hi,
I tried to update gcc, just in case.. though I'm not sure of what I do.
I ran:

pi@raspberrypi ~/MySensors $ sudo apt-get upgrade gcc

and after a little while, it ended without obvious mistake.
but if I do gcc -v again, I still get
gcc version 4.6.3 (Debian 4.6.3-14+rpi1)
(even after reboot)
Is there another step to be done, or am I using wrong command ?

gohan

try running first sudo apt-get update and then sudo apt-get upgrade , it should update all packages

ricorico94

@gohan : JUst tried it, but same result.. no change on version number.
is there something like apt-get install to be done also ?

gohan

I don't know really... I am using dietpi on a RPI3 and there is a convenient tool that you can check what to install and installs for you and among the others I have chosen the "Build-Essentials" that contains all the common packages for compile, so I don't know what packages are included.

marceloaqno

@ricorico94 Do you see gcc-4.9 in the list returned by the command below?

sudo apt-cache search gcc

If it's listed, try installing it by specifying the version:

sudo apt-get install gcc-4.9

ricmail85

Hi, wouldn't be proper to include in the guide also the command "--my-rfm69-irq-pin=22" during the configure procedure in order to improve the throughput for the rfm69 radios?

ricorico94

Hi,
Thanks to @marceloaqno and @Gohan and @arraWX , I could progress somewhow.. but still not working.

When listing the versions as per Marceloagno advice, I could see gcc-4.6 and -4.7 and 4.8 but nothing else (no 4.9).
I then decided to take the risk of installing the 4.8.. The commands from Marcelagno did not work (well, I mean gcc - v was still showing 4.6).
Then I followed this tutorial on upgrade step by step to upgrade to gcc-4.8 and then the make command apparently succeeded (well, plenty messages, some warnings.. but no error apparently, as ar as I could see. I dd not find the folders desribed in website, but the commands were still ok.. weird, but I'm too rookie..)

I then followed again the Mysensors tutorial with
sudo ./bin/mysgw -h
sudo ./bin/mysgw -d (and no error message. great!)
sudo make install
but then I ran
sudo systemctl enable mysgw.service
and I got error message

sudo: systemctl: command not found

After some search, I saw that it's a Jessie command whereas I discovered that my good old version of Rasp Pi, which was built from the standard Domoticz image in 2015 is still Wheezy

pi@raspberrypi ~/MySensors $ cat /etc/os-release
PRETTY_NAME="Raspbian GNU/Linux 7 (wheezy)"
NAME="Raspbian GNU/Linux"
VERSION_ID="7"
VERSION="7 (wheezy)"
ID=raspbian
ID_LIKE=debian
ANSI_COLOR="1;31"
HOME_URL="http://www.raspbian.org/"
SUPPORT_URL="http://www.raspbian.org/RaspbianForums"
BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs"

Any idea of what I should do now?..
another commande equivalent to the systemctl ?
an upgrade to Jessie (any risk ? and how to do it safely ?)

br,
Ricorico94

petewill

I am new to Linux and hopefully have an easy question...
I have followed the build instructions and everything seems to be working well so far. One issue I'm having is getting node-red to see the usb port (/dev/ttyUSB020). I did some searching online and found that if I run the following command node-red will see the port and things start working.

sudo chmod 666 /dev/ttyUSB020

The problem is that each time I reboot the Pi the command needs to be run again. Does anyone have any ideas on how I can resolve this so I don't need to run the command each time the system is booted? Thanks in advance.

mfalkvidd

@petewill you can put the chmod command in /etc/rc.local
That will execute it on every boot.
https://www.raspberrypi.org/documentation/linux/usage/rc-local.md

gohan

@petewill or you can compile the gateway as ethernet or mqtt that are both supported by node-red, making life a little easier

petewill

@mfalkvidd Thanks. I thought about doing something like that but I wasn't sure that was the best process or if something should be modified during the install. I'll give it a shot this way though. Thanks again.

petewill

@gohan Sorry, I did not see your reply earlier. I tried an ethernet gateway in node-red a while ago and could never get it to work with Vera. There was some port conflicts or something. I have never played with mqtt. I need to learn it at some point but I am hoping to finish this project so I can move on to some others. Do you think I will gain significant advantages by using that over a serial/usb gateway?

gohan

From a node-red perspective, IMHO, mqtt is easier to handle even without specific mysensors nodes, but it all depends what you need to do. I played with it some months ago but I got stuck when I had to start using javascript as I still don't know that language, but it was quite easy to link mysensors values to the dashboard without actually touching any code.

petewill

@gohan Thanks! I seem to have the serial stuff working well (but haven't yet put it into production) so I think I'll go that way for now. I definitely need to look into mqtt at some point though.

gohan

Ofc it has its PROs and CONs but I believe it is the way to go for the future.

fleinze

I compiled the gateway for spi1 because I have a display using spi0. Two problems I came across:

the master branch doesn't work. It compiles, it seems to work but it never receives anything.
the development branch works but I needed to define the right cs-pin even if I redirected the pin in config.txt (with dtoverlay=spi1-1cs,cs0_pin=16)
The following configure worked for me:

./configure --spi-driver=SPIDEV --spi-spidev-device=/dev/spidev1.0 --my-rf24-cs-pin=36 --my-rf24-ce-pin=33 --my-rf24-irq-pin=31

Inso

For the ones having problems with the stable build (Version 2.1.1), always getting "mysgw: !TSM:INIT:TSP FAIL":
Seems there is a bug, you have to install "development" (Version 2.2.0)
Maybe someone adds an note on top of the tutorial, so others won´t also spend hours in searching for the problem on their Pi/Hardware.

gohan

So far it looks to me it is something related to the latest versions of Linux since it was working on older releases

Inso

@gohan ah okay wasn´t aware of it, as the dev channel worked I assumed the bug at MySensors.
However, would be awesome if there were a little hint in the tutorial. Took plenty of time to find out it was an software incompability

arraWX

A little hint in the tutorial would have saved me a lot of time too.

gohan

I added a comment; I hope my English is sufficiently clear

Sergio Rius

Today my rPi gateway (2.1.1 stable) completely stopped working as a service (cli surprisingly worked), I thought that could be some debian update so I switched to devel, but when building it I get this:

LINUX_ARCH_RASPBERRYPI -DMY_PORT=5003 -DMY_RX_MESSAGE_BUFFER_FEATURE -DMY_RF24_IRQ_PIN=18 -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/BCM/bcm2835.c -o build/drivers/BCM/bcm2835.o
drivers/BCM/bcm2835.c: In function ‘bcm2835_delayMicroseconds’:
drivers/BCM/bcm2835.c:441:40: error: expected ‘)’ before ‘PRIu64’
printf("bcm2835_delayMicroseconds %" PRIu64 "\n", micros);
^
drivers/BCM/bcm2835.c:441:40: warning: spurious trailing ‘%’ in format [-Wformat=]
Makefile:102: recipe for target 'build/drivers/BCM/bcm2835.o' failed
make: *** [build/drivers/BCM/bcm2835.o] Error 1

Is this normal? I used the same configure was working before.

mfalkvidd

@Sergio-Rius a fix is available at https://github.com/mysensors/MySensors/pull/983

It is a one line change so you can just add it manually

Sergio Rius

Thaaanksss! I'll give it a go

Sergio Rius

@mfalkvidd Mmmmm... that worked, but now I'm always getting "mysgw: !TSM:INIT:TSP FAIL" as stated avobe. But I'm on development.
Wait, seems that after the 8'th intent it's working. I'll let him go and see.

Sergio Rius

I'm afraid that after some time it stops working. I get in Domoticz:

2017-11-12 19:17:01.744 MySensors: trying to connect to: 127.0.0.1:5003
2017-11-12 19:17:02.744 TCP: Connection problem (Unable to connect to specified IP/Port)
2017-11-12 19:17:02.744 TCP: Reconnecting in 30 seconds...

Over and over again.

$ sudo systemctl status mysgw.service
● mysgw.service - MySensors Gateway daemon
Loaded: loaded (/etc/systemd/system/mysgw.service; enabled)
Active: failed (Result: signal) since dom 2017-11-12 19:16:53 CET; 5min ago
Process: 491 ExecStart=/usr/local/bin/mysgw (code=killed, signal=SEGV)
Main PID: 491 (code=killed, signal=SEGV)
nov 12 19:16:47 Domoticz systemd[1]: Started MySensors Gateway daemon.
nov 12 19:16:48 Domoticz mysgw[491]: Starting gateway...
nov 12 19:16:48 Domoticz mysgw[491]: Protocol version - 2.2.0-rc.1
nov 12 19:16:53 Domoticz systemd[1]: mysgw.service: main process exited, code=killed, status=11/SEGV
nov 12 19:16:53 Domoticz systemd[1]: Unit mysgw.service entered failed state.

But it seems Domoticz being crashing it.
If I do restart the service, Domoticz picks it and works for a while.

2017-11-12 19:24:17.562 TCP: Connection problem (Unable to connect to specified IP/Port)
2017-11-12 19:24:17.562 TCP: Reconnecting in 30 seconds...
2017-11-12 19:24:47.565 TCP: Reconnecting...
2017-11-12 19:24:47.565 MySensors: connected to: 127.0.0.1:5003
2017-11-12 19:24:48.566 MySensors: Gateway Ready...
2017-11-12 19:24:48.566 MySensors: Gateway Version: 2.2.0-rc.1
2017-11-12 19:24:49.566 MySensors: Gateway Version: 2.2.0-rc.1

Is there any further log for exactly seeing what is the crash cause?

EDIT: Also it seems that there's any comunication at all. I only get internal heartbeats on MysController.

gohan

Did you get the latest version from development branch?

Sergio Rius

@gohan Yep! I exactly ran this command:

git clone https://github.com/mysensors/MySensors.git --branch development && cd MySensors

I'm now powering off my rPi for changing the PA+LNA radio for a standard one and bypassing the power regulator.

EDIT: I've done the above tasks and still getting strange things. It may be Domoticz as:

2017-11-12 19:44:37.634 MySensors: trying to connect to: 127.0.0.1:5003
2017-11-12 19:44:37.638 RFXCOM: Using serial port: /dev/ttyUSB0
2017-11-12 19:44:38.213
2017-11-12 19:44:38.288 Error: RFXCOM: Invalid data received!....
2017-11-12 19:44:38.635 MySensors: connected to: 127.0.0.1:5003
2017-11-12 19:44:38.635 MySensors: Gateway Ready...
2017-11-12 19:44:39.635 MySensors: Gateway Version: 2.2.0-rc.1
2017-11-12 19:44:39.635 MySensors: Gateway Version: 2.2.0-rc.1
...
2017-11-12 20:26:00.153 Error: Scheduler thread seems to have ended unexpectedly
2017-11-12 20:26:00.154 Error: MySGW_NRF hardware (9) thread seems to have ended unexpectedly
2017-11-12 20:26:00.154 Error: RFXCOM hardware (15) thread seems to have ended unexpectedly
2017-11-12 20:26:00.154 Error: RFXCOM hardware (15) nothing received for more than 30 Minutes!....
2017-11-12 20:26:01.155 Error: Restarting: RFXCOM
2017-11-12 20:26:01.707 RFXCOM: Serial Worker stopped...
2017-11-12 20:26:02.722 RFXCOM: Using serial port: /dev/ttyUSB0
2017-11-12 20:26:03.297
2017-11-12 20:26:03.372 Error: RFXCOM: Invalid data received!....
2017-11-12 20:26:16.745 (RFXCOM) Temp + Humidity (Biblioteca [TH])
2017-11-12 20:26:48.745 Error: PROXY: timeout occurred, reconnecting
2017-11-12 20:26:54.716 (MySGW_NRF) Temp (Temp)
2017-11-12 20:26:54.717 (MySGW_NRF) Temp + Humidity (TempHum)
...
and stabilized

gohan

If you keep a myscontroller connected to the gateway, does it stays connected or does it get disconnected at the same time as domoticz? Also try to run the gateway from console with debug enabled so you can actually see what it is doing

alowhum

Possibly same problem with Domoticz here too. Using a directly attached NRF24 radio to a Raspberry Pi Zero W.

I tried to remake using the latest dev code, and got this error:

gcc -MT build/drivers/BCM/bcm2835.o -MMD -MP -march=armv6zk -mtune=arm1176jzf-s -mfpu=vfp -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_PORT=5003 -DMY_RF24_PA_LEVEL=RF24_PA_LOW  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/BCM/bcm2835.c -o build/drivers/BCM/bcm2835.o
drivers/BCM/bcm2835.c: In function ‘bcm2835_delayMicroseconds’:
drivers/BCM/bcm2835.c:441:40: error: expected ‘)’ before ‘PRIu64’
   printf("bcm2835_delayMicroseconds %" PRIu64 "\n", micros);
                                        ^
drivers/BCM/bcm2835.c:441:40: warning: spurious trailing ‘%’ in format [-Wformat=]
Makefile:102: recipe for target 'build/drivers/BCM/bcm2835.o' failed
make: *** [build/drivers/BCM/bcm2835.o] Error 1

// commenting out the problem allowed make to finish:

	//if (debug) {
	//	/* Cant access sytem timers in debug mode */
	//	printf("bcm2835_delayMicroseconds %" PRIu64 "\n", micros);
	//	return;
	//}

This is my config:
./configure --my-transport=nrf24 --my-rf24-pa-level=RF24_PA_LOW --my-gateway=ethernet --my-port=5003

aglock

Hello all!

I'm trying to build a gateway with a Raspberry pi2, ethernet and Domoticz.
It looks like the gateway is beeing built ok and seems to run fine but nodes can not communicate with it.
I have read most of the postings here but I can not find any solution.
Hope you guys can help? Please!

I run raspbian (Jessie)
pi@raspberrypi:~/MySensors/bin $ uname -a
Linux raspberrypi 4.9.35-v7+ #1014 SMP Fri Jun 30 14:47:43 BST 2017 armv7l GNU/Linux

Using master branch

https://www.mysensors.org/build/raspberry
git clone https://github.com/mysensors/MySensors.git --branch master

Configuring like this

pi@raspberrypi:~/MySensors $ ./configure --my-gateway=ethernet --my-port=5003 --my-transport=nrf24 --my-rf24-ce-pin=22 --my-rf24-cs-pin=24
[SECTION] Detecting target machine.
  [OK] machine detected: SoC=unknown, Type=unknown, CPU=armv7l.
[SECTION] Checking GPIO Sysfs.
  [OK] /sys/class/gpio/export found
[SECTION] Detecting SPI driver.
  [OK] SPI driver detected:SPIDEV.
[SECTION] Detecting init system.
  [OK] init system detected: systemd.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.

Obs! No Raspberry identification, why not? Maybe that is the culprit?
After make I start the gateway and get this:

pi@raspberrypi:~/MySensors $ cd bin
pi@raspberrypi:~/MySensors/bin $ sudo ./mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: New connection from 127.0.0.1
mysgw: Client 0 connected
mysgw: Client 0: 0;0;3;0;2;
mysgw: Client 0: 0;0;3;0;2;Get Version
mysgw: Client 0: 0;0;3;0;18;PING

Seems nice and dandy and Domoticz connecting fine.
Trying with this example node:

#define MY_RADIO_NRF24
#define MY_RF24_PA_LEVEL RF24_PA_LOW
#define MY_DEBUG
#define MY_NODE_ID 42
//#define MY_DEBUG_VERBOSE_RF24
#define MY_BAUD_RATE 9600

#include <MySensors.h>
#include<Arduino.h>

#define OPEN 1
#define CLOSE 0
#define CHILD_ID 1

MyMessage msg(CHILD_ID, V_TRIPPED);

uint8_t value = OPEN;

void setup()
{
  Serial.print("setup()\n");
}

void presentation()
{
  sendSketchInfo("Door", "2.1.1");
  present(CHILD_ID, S_DOOR);
  Serial.print("presentation()\n");
}

void loop()
{
  value = value == OPEN ? CLOSE : OPEN;
  send(msg.set(value));
  Serial.print("message sent");
  Serial.print(value + "\n");
  sleep(1000);
}

And recieve this when running:

--- Miniterm on /dev/ttyUSB0 9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
40 TSM:INIT
55 TSF:WUR:MS=0
77 TSM:INIT:TSP OK
96 TSM:INIT:STATID=42
120 TSF:SID:OK,ID=42
141 TSM:FPAR
190 TSF:MSG:SEND,42-42-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2267 !TSM:FPAR:NO REPLY
2291 TSM:FPAR
2340 TSF:MSG:SEND,42-42-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:

4417 !TSM:FPAR:NO REPLY
4442 TSM:FPAR
4491 TSF:MSG:SEND,42-42-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6569 !TSM:FPAR:NO REPLY
6594 TSM:FPAR
6643 TSF:MSG:SEND,42-42-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8720 !TSM:FPAR:FAIL
8740 TSM:FAIL:CNT=1
8761 TSM:FAIL:PDT

And no output in gateway either.
Both radio modules using capacitors.

What have I missed?

Thanks, Andreas!

skywatch

I tried for months to get a stable working nrf24 attached to pi to act as a gw and controller.

In the end I gave up and now have a 3.3V 8MHz pro mini gw attached to the pi. I took 0v and 5v from the pi (via a 3.3v buck converter) and serial tx and rx. Only 4 wires needed and has been as stable as can be for over a week now.

Maybe help someone with the same unsolveable problems?

gohan

@aglock I put a note on the raspberry gateway page to use latest development in case of problems with stable. Did you try?

aglock

@gohan yes. Interesting though when I used git to switch between branches it said all files where the same?
Do you think the fault is in the gateway somehow?

aglock

@gohan Tried it again
configure now recognizes the rpi:

pi@raspberrypi:~/mys_dev $ ./configure --my-gateway=ethernet --my-port=5003 --my-transport=nrf24 --my-rf24-ce-pin=22 --my-rf24-cs-pin=24
[SECTION] Detecting target machine.
  [OK] machine detected: SoC=BCM2836, Type=rpi2, CPU=armv7l.
[SECTION] Detecting SPI driver.
  [OK] SPI driver detected:BCM.
[SECTION] Detecting init system.
  [OK] init system detected: systemd.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.

But make fails with the following error:

-I./core -I./drivers/Linux -I./drivers/BCM -c drivers/BCM/bcm2835.c -o build/drivers/BCM/bcm2835.o
drivers/BCM/bcm2835.c: In function ‘bcm2835_delayMicroseconds’:
drivers/BCM/bcm2835.c:441:40: error: expected ‘)’ before ‘PRIu64’
   printf("bcm2835_delayMicroseconds %" PRIu64 "\n", micros);
                                        ^
drivers/BCM/bcm2835.c:441:40: warning: spurious trailing ‘%’ in format [-Wformat=]
Makefile:102: recipe for target 'build/drivers/BCM/bcm2835.o' failed
make: *** [build/drivers/BCM/bcm2835.o] Error 1
pi@raspberrypi:~/mys_dev $

What to do about it?

mfalkvidd

@aglock see https://forum.mysensors.org/post/79403

aglock

@mfalkvidd Wow, thanks that works!

Woeka

Got mysensors gateway working on gpio of my Pi again using ./configure --my-transport=nrf24 --my-rf24-irq-pin=15 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18 --my-gateway=ethernet --my-port=5003

However on tx or tx always the two leds connected to pin 16 and 18 are lit. More people with the same problem?

sineverba

@Woeka There is (on Arduino Gateway) a function named "DEFINE INVERSE BLINK". Try to search for same for PI....

romeo01

Can we use the "debug ota log" features with the raspberryPi gateway ??

My node is not accessible and runs MYSBootloader.
My gateway is raspberryPI.

Now, I need to update the firmware on my node. Via MYSController, no problems, upload runs like a charm.

But how to do for debugging my sketch ? Some bugs appear...... , I need to take a look on some vars values.
Usually, I use the serial port with serial.print(some vars).
Which alternative I have to use without serial port, only OTA features ?

Thanks for the great work !!

gohan

Unless you are using an esp8266, I don't think you can remote debug a pro mini. @sundberg84 is working on a serial logger to microsd card, maybe it could help you in some way

romeo01

In fact, I do not need to log, but need to look what's happen in my sketch.
The new "OTALog" function, MY_OTA_LOG_SENDER_FEATURE or MY_DEBUG_OTA seems to be the good way.
From the docs, it allows to send a debug message to another node or gateway via OTA.

But how to got the debug message from OTA node, on the gateway side (RaspberryPi) ?

gohan

@romeo01 said in Building a Raspberry Pi Gateway:

MY_DEBUG_OTA

I'd start reading from here https://www.mysensors.org/apidocs-beta/group__SerialDebugGrpPub.html#ga6bd5956352d3a184a0cb02783b8d35ff

romeo01

@gohan said in Building a Raspberry Pi Gateway:

@romeo01 said in Building a Raspberry Pi Gateway:

MY_DEBUG_OTA

I'd start reading from here https://www.mysensors.org/apidocs-beta/group__SerialDebugGrpPub.html#ga6bd5956352d3a184a0cb02783b8d35ff

Well, you found the starting point !

MY_OTA_LOG_SENDER_FEATURE & MY_DEBUG_OTA are enabled on my OTA node.

Again the same question: What I have to do on the gateway side ?
Is it possible with the raspberry Gateway ?

I'm still looking for debugging my sketch in remote. I need to have a look on the debug messages. I reminder, the node is not accessible and runs MYSbootloader.

gohan

If I understood well, you need to set a target node ID that will receive the debug and then make a node with that ID in order to get the debug messages

romeo01

Exactly, but I would like to use the gateway (raspberry) as target.
Is that possible ?
If yes, how to display the debug message on the gateway.
I have an access to my gateway only via SSH.

gohan

I have no idea if can do it, but you could just have a node connected to USB port of the rpi and do a "cat" on the USB port and you can read the debug from the node

signal15

Is it possible to build a gateway that is MQTT, but also listens on port 5003? I want to send my data up to AWS IoT, but I also need port 5003 for Vera integration.

gohan

You can use node-red to bridge the ethernet gateway and the aws service. Are you sure vera plug in doesn't support mqtt?

signal15

@gohan, there are two MQTT plugins for the Vera with varying capabilities. But, the mysensors plugin for Vera doesn't appear to support MQTT at all. I could probably get one of those MQTT plugins working, but I'm not sure how stable they are. I hate installing unstable plugins and having them crash LUUP. I need to maintain a positive WAF (Wife Acceptance Factor), and broken HA doesn't help with that.

gohan

I guess node-red is the best option for you

pepson

Hi
I start build MySensors Gateway on my Rpi3. I use radio RFM69HW and connected it as show on page to GPIO.
https://www.mysensors.org/build/raspberry
I build it by command:
./configure --my-transport=rfm69 --my-rfm69-frequency=868 --my-is-rfm69hw --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB1

Then make. But in Domoticz when i run and add to hardware i have error:
2017-12-27 17:05:09.419 MySensors: Using serial port: /dev/ttyUSB1
2017-12-27 17:05:09.419 MySensors: Gateway Version: 2.2.0-rc.2
2017-12-27 17:05:09.420 Error: Serial Port closed!... Error: End of file
2017-12-27 17:05:10.419 MySensors: retrying in 30 seconds...
2017-12-27 17:05:39.422 MySensors: Using serial port: /dev/ttyUSB1
2017-12-27 17:05:39.422 Error: Serial Port closed!... Error: End of file
2017-12-27 17:05:40.422 MySensors: retrying in 30 seconds...
2017-12-27 17:06:09.425 MySensors: Using serial port: /dev/ttyUSB1
2017-12-27 17:06:09.425 Error: Serial Port closed!... Error: End of file
2017-12-27 17:06:10.425 MySensors: retrying in 30 seconds...
2017-12-27 17:06:39.427 MySensors: Using serial port: /dev/ttyUSB1
2017-12-27 17:06:39.428 Error: Serial Port closed!... Error: End of file
2017-12-27 17:06:40.428 MySensors: retrying in 30 seconds...
2017-12-27 17:07:09.430 MySensors: Using serial port: /dev/ttyUSB1
2017-12-27 17:07:09.430 Error: Serial Port closed!... Error: End of file

port ttyUSB1 is empty as i check.
Please help me where is the problem...

mfalkvidd

@pepson what output did you get when you tested the gateway?

pepson

mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-rc2
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.2.0-rc2
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1

mfalkvidd

@pepson thanks. Nothing strange there. Anything i teresting in var/log/syslog after enabling debug output?

pepson

Dec 27 21:11:48 domoticz systemd[1]: Stopping User Manager for UID 1000...
Dec 27 21:11:48 domoticz systemd[715]: Stopped target Default.
Dec 27 21:11:48 domoticz systemd[715]: Stopped target Basic System.
Dec 27 21:11:48 domoticz systemd[715]: Stopped target Sockets.
Dec 27 21:11:48 domoticz systemd[715]: Closed GnuPG cryptographic agent (access for web browsers).
Dec 27 21:11:48 domoticz systemd[715]: Stopped target Paths.
Dec 27 21:11:48 domoticz systemd[715]: Closed GnuPG cryptographic agent and passphrase cache (restricted).
Dec 27 21:11:48 domoticz systemd[715]: Closed GnuPG cryptographic agent and passphrase cache.
Dec 27 21:11:48 domoticz systemd[715]: Stopped target Timers.
Dec 27 21:11:48 domoticz systemd[715]: Closed GnuPG cryptographic agent (ssh-agent emulation).
Dec 27 21:11:48 domoticz systemd[715]: Reached target Shutdown.
Dec 27 21:11:48 domoticz systemd[715]: Starting Exit the Session...
Dec 27 21:11:48 domoticz systemd[715]: Received SIGRTMIN+24 from PID 800 (kill).
Dec 27 21:11:48 domoticz systemd[1]: Stopped User Manager for UID 1000.
Dec 27 21:11:48 domoticz systemd[1]: Removed slice User Slice of pi.
Dec 27 21:11:54 domoticz systemd[1]: Stopping Save/Restore Sound Card State...
Dec 27 21:11:54 domoticz systemd[1]: Unmounting RPC Pipe File System...
Dec 27 21:11:54 domoticz systemd[1]: Stopped target Graphical Interface.
Dec 27 21:12:27 domoticz systemd-modules-load[125]: Inserted module 'i2c_dev'
Dec 27 21:12:27 domoticz fake-hwclock[115]: Wed 27 Dec 20:12:25 UTC 2017
Dec 27 21:12:27 domoticz systemd[1]: Mounted Configuration File System.
Dec 27 21:12:27 domoticz systemd[1]: Started Apply Kernel Variables.
Dec 27 21:12:27 domoticz systemd-fsck[127]: e2fsck 1.43.4 (31-Jan-2017)
Dec 27 21:12:27 domoticz systemd[1]: Started Create Static Device Nodes in /dev.
Dec 27 21:12:27 domoticz systemd[1]: Starting udev Kernel Device Manager...
Dec 27 21:12:27 domoticz systemd-fsck[127]: rootfs: clean, 54121/474240 files, 431837/1933824 blocks
Dec 27 21:12:27 domoticz systemd[1]: Started File System Check on Root Device.
Dec 27 21:12:27 domoticz systemd[1]: Starting Remount Root and Kernel File Systems...
Dec 27 21:12:27 domoticz systemd[1]: Started Remount Root and Kernel File Systems.
Dec 27 21:12:27 domoticz systemd[1]: Starting Load/Save Random Seed...
Dec 27 21:12:27 domoticz systemd[1]: Starting udev Coldplug all Devices...
Dec 27 21:12:27 domoticz systemd[1]: Starting Flush Journal to Persistent Storage...
Dec 27 21:12:27 domoticz systemd[1]: Started Flush Journal to Persistent Storage.
Dec 27 21:12:27 domoticz systemd[1]: Started Load/Save Random Seed.
Dec 27 21:12:27 domoticz systemd[1]: Started udev Kernel Device Manager.
Dec 27 21:12:27 domoticz systemd[1]: Started Set the console keyboard layout.
Dec 27 21:12:27 domoticz systemd[1]: Reached target Local File Systems (Pre).
Dec 27 21:12:27 domoticz systemd[1]: Started udev Coldplug all Devices.
Dec 27 21:12:27 domoticz systemd[1]: Starting Show Plymouth Boot Screen...
Dec 27 21:12:27 domoticz systemd[1]: Received SIGRTMIN+20 from PID 190 (plymouthd).
Dec 27 21:12:27 domoticz systemd[1]: Started Show Plymouth Boot Screen.
Dec 27 21:12:27 domoticz systemd[1]: Found device /dev/disk/by-partuuid/e80766f2-01.
Dec 27 21:12:27 domoticz systemd[1]: Starting File System Check on /dev/disk/by-partuuid/e80766f2-01...
Dec 27 21:12:27 domoticz systemd[1]: Started Forward Password Requests to Plymouth Directory Watch.
Dec 27 21:12:27 domoticz systemd[1]: Reached target Encrypted Volumes.
Dec 27 21:12:27 domoticz systemd[1]: Reached target Paths.
Dec 27 21:12:27 domoticz mtp-probe: checking bus 1, device 3: "/sys/devices/platform/soc/3f980000.usb/usb1/1-1/1-1.1"
Dec 27 21:12:27 domoticz mtp-probe: bus: 1, device: 3 was not an MTP device
Dec 27 21:12:27 domoticz systemd[1]: Reached target Sound Card.
Dec 27 21:12:27 domoticz systemd[1]: Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
Dec 27 21:12:27 domoticz systemd[1]: Starting Load/Save RF Kill Switch Status...
Dec 27 21:12:27 domoticz systemd-fsck[227]: fsck.fat 4.1 (2017-01-24)
Dec 27 21:12:27 domoticz systemd-fsck[227]: /dev/mmcblk0p1: 150 files, 42691/83705 clusters
Dec 27 21:12:27 domoticz systemd[1]: Started File System Check on /dev/disk/by-partuuid/e80766f2-01.
Dec 27 21:12:27 domoticz systemd[1]: Mounting /boot...
Dec 27 21:12:27 domoticz systemd[1]: Started Load/Save RF Kill Switch Status.
Dec 27 21:12:27 domoticz systemd[1]: Mounted /boot.
Dec 27 21:12:27 domoticz systemd[1]: Reached target Local File Systems.
Dec 27 21:12:27 domoticz systemd[1]: Starting Preprocess NFS configuration...
Dec 27 21:12:27 domoticz systemd[1]: Starting Tell Plymouth To Write Out Runtime Data...
Dec 27 21:12:27 domoticz systemd[1]: Starting Set console font and keymap...
Dec 27 21:12:27 domoticz systemd[1]: Starting Raise network interfaces...
Dec 27 21:12:27 domoticz systemd[1]: Starting Create Volatile Files and Directories...
Dec 27 21:12:27 domoticz systemd[1]: Started Tell Plymouth To Write Out Runtime Data.
Dec 27 21:12:27 domoticz systemd[1]: Started Preprocess NFS configuration.
Dec 27 21:12:27 domoticz systemd[1]: Reached target NFS client services.
Dec 27 21:12:27 domoticz systemd[1]: Reached target Remote File Systems (Pre).
Dec 27 21:12:27 domoticz systemd[1]: Reached target Remote File Systems.
Dec 27 21:12:27 domoticz systemd[1]: Started Set console font and keymap.
Dec 27 21:12:27 domoticz systemd[1]: Started Create Volatile Files and Directories.
Dec 27 21:12:27 domoticz systemd[1]: Starting Network Time Synchronization...
Dec 27 21:12:27 domoticz systemd[1]: Starting Update UTMP about System Boot/Shutdown...
Dec 27 21:12:27 domoticz systemd[1]: Started Update UTMP about System Boot/Shutdown.
Dec 27 21:12:27 domoticz systemd[1]: Started Raise network interfaces.
Dec 27 21:12:27 domoticz systemd[1]: Started Network Time Synchronization.
Dec 27 21:12:27 domoticz systemd[1]: Reached target System Initialization.
Dec 27 21:12:27 domoticz systemd[1]: Started Daily Cleanup of Temporary Directories.
Dec 27 21:12:27 domoticz systemd[1]: Listening on D-Bus System Message Bus Socket.
Dec 27 21:12:27 domoticz systemd[1]: Listening on triggerhappy.socket.
Dec 27 21:12:27 domoticz systemd[1]: Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
Dec 27 21:12:27 domoticz systemd[1]: Reached target Sockets.
Dec 27 21:12:27 domoticz systemd[1]: Reached target Basic System.
Dec 27 21:12:27 domoticz systemd[1]: Starting LSB: Start OWFS at boot time...
Dec 27 21:12:27 domoticz systemd[1]: Starting Login Service...
Dec 27 21:12:27 domoticz systemd[1]: Starting Avahi mDNS/DNS-SD Stack...
Dec 27 21:12:27 domoticz systemd[1]: Started Regular background program processing daemon.
Dec 27 21:12:27 domoticz systemd[1]: Starting LSB: Autogenerate and use a swap file...
Dec 27 21:12:27 domoticz systemd[1]: Starting LSB: Switch to ondemand cpu governor (unless shift key is pressed)...
Dec 27 21:12:27 domoticz systemd[1]: Starting triggerhappy global hotkey daemon...
Dec 27 21:12:27 domoticz systemd[1]: Started MySensors Gateway daemon.
Dec 27 21:12:27 domoticz systemd[1]: Starting System Logging Service...
Dec 27 21:12:27 domoticz systemd[1]: Starting Save/Restore Sound Card State...
Dec 27 21:12:27 domoticz systemd[1]: Starting dhcpcd on all interfaces...
Dec 27 21:12:27 domoticz systemd[1]: Started D-Bus System Message Bus.
Dec 27 21:12:27 domoticz cron[328]: (CRON) INFO (pidfile fd = 3)
Dec 27 21:12:27 domoticz cron[328]: (CRON) INFO (Running @reboot jobs)
Dec 27 21:12:27 domoticz thd[331]: Found socket passed from systemd
Dec 27 21:12:27 domoticz dhcpcd[339]: dev: loaded udev
Dec 27 21:12:27 domoticz mysgw: Starting gateway...
Dec 27 21:12:27 domoticz mysgw: Protocol version - 2.2.0-rc.2
Dec 27 21:12:27 domoticz avahi-daemon[327]: Found user 'avahi' (UID 108) and group 'avahi' (GID 112).
Dec 27 21:12:27 domoticz avahi-daemon[327]: Successfully dropped root privileges.
Dec 27 21:12:27 domoticz avahi-daemon[327]: avahi-daemon 0.6.32 starting up.
Dec 27 21:12:27 domoticz liblogging-stdlog:  [origin software="rsyslogd" swVersion="8.24.0" x-pid="334" x-info="http://www.rsyslog.com"] start
Dec 27 21:12:27 domoticz kernel: [    0.000000] Booting Linux on physical CPU 0x0
Dec 27 21:12:27 domoticz kernel: [    0.000000] Linux version 4.9.70-v7+ (dc4@dc4-XPS13-9333) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611) ) #1068 SMP Mon Dec 18 22:12:55 GMT 2017
Dec 27 21:12:27 domoticz kernel: [    0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
Dec 27 21:12:27 domoticz kernel: [    0.000000] CPU: div instructions available: patching division code
Dec 27 21:12:27 domoticz kernel: [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Dec 27 21:12:27 domoticz kernel: [    0.000000] OF: fdt:Machine model: Raspberry Pi 3 Model B Rev 1.2
Dec 27 21:12:27 domoticz kernel: [    0.000000] cma: Reserved 8 MiB at 0x3dc00000
Dec 27 21:12:27 domoticz kernel: [    0.000000] Memory policy: Data cache writealloc
Dec 27 21:12:27 domoticz kernel: [    0.000000] On node 0 totalpages: 255488
Dec 27 21:12:27 domoticz kernel: [    0.000000] free_area_init_node: node 0, pgdat 80c6f400, node_mem_map bd336000
Dec 27 21:12:27 domoticz kernel: [    0.000000]   Normal zone: 2246 pages used for memmap
Dec 27 21:12:27 domoticz kernel: [    0.000000]   Normal zone: 0 pages reserved
Dec 27 21:12:27 domoticz kernel: [    0.000000]   Normal zone: 255488 pages, LIFO batch:31
Dec 27 21:12:27 domoticz kernel: [    0.000000] percpu: Embedded 14 pages/cpu @be5b0000 s25600 r8192 d23552 u57344
Dec 27 21:12:27 domoticz kernel: [    0.000000] pcpu-alloc: s25600 r8192 d23552 u57344 alloc=14*4096
Dec 27 21:12:27 domoticz kernel: [    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
Dec 27 21:12:27 domoticz kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 253242
Dec 27 21:12:27 domoticz kernel: [    0.000000] Kernel command line: 8250.nr_uarts=1 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708_fb.fbdepth=16 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3f000000 vc_mem.mem_size=0x3f600000  dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=e80766f2-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
Dec 27 21:12:27 domoticz kernel: [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
Dec 27 21:12:27 domoticz kernel: [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Dec 27 21:12:27 domoticz kernel: [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Dec 27 21:12:27 domoticz kernel: [    0.000000] Memory: 991096K/1021952K available (7168K kernel code, 486K rwdata, 2012K rodata, 1024K init, 770K bss, 22664K reserved, 8192K cma-reserved)
Dec 27 21:12:27 domoticz kernel: [    0.000000] Virtual kernel memory layout:
Dec 27 21:12:27 domoticz kernel: [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
Dec 27 21:12:27 domoticz kernel: [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
Dec 27 21:12:27 domoticz kernel: [    0.000000]     vmalloc : 0xbe800000 - 0xff800000   (1040 MB)
Dec 27 21:12:27 domoticz kernel: [    0.000000]     lowmem  : 0x80000000 - 0xbe600000   ( 998 MB)
Dec 27 21:12:27 domoticz kernel: [    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
Dec 27 21:12:27 domoticz kernel: [    0.000000]       .text : 0x80008000 - 0x80800000   (8160 kB)
Dec 27 21:12:27 domoticz kernel: [    0.000000]       .init : 0x80b00000 - 0x80c00000   (1024 kB)
Dec 27 21:12:27 domoticz kernel: [    0.000000]       .data : 0x80c00000 - 0x80c798bc   ( 487 kB)
Dec 27 21:12:27 domoticz kernel: [    0.000000]        .bss : 0x80c7b000 - 0x80d3b9a4   ( 771 kB)
Dec 27 21:12:27 domoticz kernel: [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Dec 27 21:12:27 domoticz kernel: [    0.000000] Hierarchical RCU implementation.
Dec 27 21:12:27 domoticz kernel: [    0.000000] 	Build-time adjustment of leaf fanout to 32.
Dec 27 21:12:27 domoticz kernel: [    0.000000] NR_IRQS:16 nr_irqs:16 16
Dec 27 21:12:27 domoticz kernel: [    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
Dec 27 21:12:27 domoticz kernel: [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
Dec 27 21:12:27 domoticz kernel: [    0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
Dec 27 21:12:27 domoticz kernel: [    0.000022] Switching to timer-based delay loop, resolution 52ns
Dec 27 21:12:27 domoticz kernel: [    0.000304] Console: colour dummy device 80x30
Dec 27 21:12:27 domoticz kernel: [    0.001203] console [tty1] enabled
Dec 27 21:12:27 domoticz kernel: [    0.001250] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
Dec 27 21:12:27 domoticz kernel: [    0.001318] pid_max: default: 32768 minimum: 301
Dec 27 21:12:27 domoticz kernel: [    0.001653] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Dec 27 21:12:27 domoticz kernel: [    0.001696] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
Dec 27 21:12:27 domoticz kernel: [    0.002734] Disabling memory control group subsystem
Dec 27 21:12:27 domoticz kernel: [    0.002838] CPU: Testing write buffer coherency: ok
Dec 27 21:12:27 domoticz kernel: [    0.002901] ftrace: allocating 22400 entries in 66 pages
Dec 27 21:12:27 domoticz kernel: [    0.049380] CPU0: update cpu_capacity 1024
Dec 27 21:12:27 domoticz kernel: [    0.049432] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Dec 27 21:12:27 domoticz kernel: [    0.049493] Setting up static identity map for 0x100000 - 0x100034
Dec 27 21:12:27 domoticz kernel: [    0.051403] CPU1: update cpu_capacity 1024
Dec 27 21:12:27 domoticz kernel: [    0.051410] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Dec 27 21:12:27 domoticz kernel: [    0.052106] CPU2: update cpu_capacity 1024
Dec 27 21:12:27 domoticz kernel: [    0.052113] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
Dec 27 21:12:27 domoticz kernel: [    0.052791] CPU3: update cpu_capacity 1024
Dec 27 21:12:27 domoticz kernel: [    0.052798] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Dec 27 21:12:27 domoticz kernel: [    0.052887] Brought up 4 CPUs
Dec 27 21:12:27 domoticz kernel: [    0.053059] SMP: Total of 4 processors activated (153.60 BogoMIPS).
Dec 27 21:12:27 domoticz kernel: [    0.053089] CPU: All CPU(s) started in HYP mode.
Dec 27 21:12:27 domoticz kernel: [    0.053115] CPU: Virtualization extensions available.
Dec 27 21:12:27 domoticz kernel: [    0.053944] devtmpfs: initialized
Dec 27 21:12:27 domoticz kernel: [    0.065214] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
Dec 27 21:12:27 domoticz kernel: [    0.065538] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Dec 27 21:12:27 domoticz kernel: [    0.065601] futex hash table entries: 1024 (order: 4, 65536 bytes)
Dec 27 21:12:27 domoticz kernel: [    0.066163] pinctrl core: initialized pinctrl subsystem
Dec 27 21:12:27 domoticz kernel: [    0.067095] NET: Registered protocol family 16
Dec 27 21:12:27 domoticz kernel: [    0.069334] DMA: preallocated 1024 KiB pool for atomic coherent allocations
Dec 27 21:12:27 domoticz kernel: [    0.078209] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
Dec 27 21:12:27 domoticz kernel: [    0.078258] hw-breakpoint: maximum watchpoint size is 8 bytes.
Dec 27 21:12:27 domoticz kernel: [    0.078436] Serial: AMBA PL011 UART driver
Dec 27 21:12:27 domoticz kernel: [    0.080361] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
Dec 27 21:12:27 domoticz kernel: [    0.080925] uart-pl011 3f201000.serial: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe
Dec 27 21:12:27 domoticz kernel: [    0.150223] bcm2835-dma 3f007000.dma: DMA legacy API manager at be80f000, dmachans=0x1
Dec 27 21:12:27 domoticz kernel: [    0.152120] SCSI subsystem initialized
Dec 27 21:12:27 domoticz kernel: [    0.152301] usbcore: registered new interface driver usbfs
Dec 27 21:12:27 domoticz kernel: [    0.152411] usbcore: registered new interface driver hub
Dec 27 21:12:27 domoticz kernel: [    0.152527] usbcore: registered new device driver usb
Dec 27 21:12:27 domoticz kernel: [    0.159194] raspberrypi-firmware soc:firmware: Attached to firmware from 2017-12-01 16:17
Dec 27 21:12:27 domoticz kernel: [    0.160594] clocksource: Switched to clocksource arch_sys_counter
Dec 27 21:12:27 domoticz kernel: [    0.207210] VFS: Disk quotas dquot_6.6.0
Dec 27 21:12:27 domoticz kernel: [    0.207324] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Dec 27 21:12:27 domoticz kernel: [    0.207555] FS-Cache: Loaded
Dec 27 21:12:27 domoticz kernel: [    0.207822] CacheFiles: Loaded
Dec 27 21:12:27 domoticz kernel: [    0.220056] NET: Registered protocol family 2
Dec 27 21:12:27 domoticz kernel: [    0.220996] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
Dec 27 21:12:27 domoticz kernel: [    0.221133] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
Dec 27 21:12:27 domoticz kernel: [    0.221344] TCP: Hash tables configured (established 8192 bind 8192)
Dec 27 21:12:27 domoticz kernel: [    0.221457] UDP hash table entries: 512 (order: 2, 16384 bytes)
Dec 27 21:12:27 domoticz kernel: [    0.221525] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
Dec 27 21:12:27 domoticz kernel: [    0.221756] NET: Registered protocol family 1
Dec 27 21:12:27 domoticz kernel: [    0.222236] RPC: Registered named UNIX socket transport module.
Dec 27 21:12:27 domoticz kernel: [    0.222269] RPC: Registered udp transport module.
Dec 27 21:12:27 domoticz kernel: [    0.222297] RPC: Registered tcp transport module.
Dec 27 21:12:27 domoticz kernel: [    0.222324] RPC: Registered tcp NFSv4.1 backchannel transport module.
Dec 27 21:12:27 domoticz kernel: [    0.223276] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
Dec 27 21:12:27 domoticz kernel: [    0.225612] workingset: timestamp_bits=14 max_order=18 bucket_order=4
Dec 27 21:12:27 domoticz kernel: [    0.241781] FS-Cache: Netfs 'nfs' registered for caching
Dec 27 21:12:27 domoticz kernel: [    0.242797] NFS: Registering the id_resolver key type
Dec 27 21:12:27 domoticz kernel: [    0.242860] Key type id_resolver registered
Dec 27 21:12:27 domoticz kernel: [    0.242888] Key type id_legacy registered
Dec 27 21:12:27 domoticz kernel: [    0.245340] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
Dec 27 21:12:27 domoticz kernel: [    0.245505] io scheduler noop registered
Dec 27 21:12:27 domoticz kernel: [    0.245535] io scheduler deadline registered (default)
Dec 27 21:12:27 domoticz kernel: [    0.245816] io scheduler cfq registered
Dec 27 21:12:27 domoticz kernel: [    0.251562] BCM2708FB: allocated DMA memory fdd10000
Dec 27 21:12:27 domoticz kernel: [    0.251615] BCM2708FB: allocated DMA channel 0 @ be80f000
Dec 27 21:12:27 domoticz kernel: [    0.256725] Console: switching to colour frame buffer device 82x26
Dec 27 21:12:27 domoticz kernel: [    0.261582] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
Dec 27 21:12:27 domoticz kernel: [    0.264453] bcm2835-rng 3f104000.rng: hwrng registered
Dec 27 21:12:27 domoticz kernel: [    0.265902] vc-mem: phys_addr:0x00000000 mem_base=0x3f000000 mem_size:0x3f600000(1014 MiB)
Dec 27 21:12:27 domoticz kernel: [    0.269187] vc-sm: Videocore shared memory driver
Dec 27 21:12:27 domoticz kernel: [    0.285964] brd: module loaded
Dec 27 21:12:27 domoticz kernel: [    0.296350] loop: module loaded
Dec 27 21:12:27 domoticz kernel: [    0.297737] Loading iSCSI transport class v2.0-870.
Dec 27 21:12:27 domoticz kernel: [    0.299603] usbcore: registered new interface driver smsc95xx
Dec 27 21:12:27 domoticz kernel: [    0.300990] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
Dec 27 21:12:27 domoticz kernel: [    0.530382] Core Release: 2.80a
Dec 27 21:12:27 domoticz kernel: [    0.531748] Setting default values for core params
Dec 27 21:12:27 domoticz kernel: [    0.533143] Finished setting default values for core params
Dec 27 21:12:27 domoticz kernel: [    0.734883] Using Buffer DMA mode
Dec 27 21:12:27 domoticz kernel: [    0.736187] Periodic Transfer Interrupt Enhancement - disabled
Dec 27 21:12:27 domoticz kernel: [    0.737532] Multiprocessor Interrupt Enhancement - disabled
Dec 27 21:12:27 domoticz kernel: [    0.738902] OTG VER PARAM: 0, OTG VER FLAG: 0
Dec 27 21:12:27 domoticz kernel: [    0.740281] Dedicated Tx FIFOs mode
Dec 27 21:12:27 domoticz kernel: [    0.742000] WARN::dwc_otg_hcd_init:1032: FIQ DMA bounce buffers: virt = 0xbdd04000 dma = 0xfdd04000 len=9024
Dec 27 21:12:27 domoticz kernel: [    0.744889] FIQ FSM acceleration enabled for :
Dec 27 21:12:27 domoticz kernel: [    0.744889] Non-periodic Split Transactions
Dec 27 21:12:27 domoticz kernel: [    0.744889] Periodic Split Transactions
Dec 27 21:12:27 domoticz kernel: [    0.744889] High-Speed Isochronous Endpoints
Dec 27 21:12:27 domoticz kernel: [    0.744889] Interrupt/Control Split Transaction hack enabled
Dec 27 21:12:27 domoticz kernel: [    0.751657] dwc_otg: Microframe scheduler enabled
Dec 27 21:12:27 domoticz kernel: [    0.751707] WARN::hcd_init_fiq:459: FIQ on core 1 at 0x80590aa0
Dec 27 21:12:27 domoticz kernel: [    0.753058] WARN::hcd_init_fiq:460: FIQ ASM at 0x80590e10 length 36
Dec 27 21:12:27 domoticz kernel: [    0.754417] WARN::hcd_init_fiq:486: MPHI regs_base at 0xbe87a000
Dec 27 21:12:27 domoticz kernel: [    0.755813] dwc_otg 3f980000.usb: DWC OTG Controller
Dec 27 21:12:27 domoticz kernel: [    0.757179] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
Dec 27 21:12:27 domoticz kernel: [    0.758567] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000
Dec 27 21:12:27 domoticz kernel: [    0.759940] Init: Port Power? op_state=1
Dec 27 21:12:27 domoticz kernel: [    0.761277] Init: Power Port (0)
Dec 27 21:12:27 domoticz kernel: [    0.762752] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Dec 27 21:12:27 domoticz kernel: [    0.764101] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Dec 27 21:12:27 domoticz kernel: [    0.765440] usb usb1: Product: DWC OTG Controller
Dec 27 21:12:27 domoticz kernel: [    0.766751] usb usb1: Manufacturer: Linux 4.9.70-v7+ dwc_otg_hcd
Dec 27 21:12:27 domoticz kernel: [    0.768074] usb usb1: SerialNumber: 3f980000.usb
Dec 27 21:12:27 domoticz kernel: [    0.770222] hub 1-0:1.0: USB hub found
Dec 27 21:12:27 domoticz kernel: [    0.771542] hub 1-0:1.0: 1 port detected
Dec 27 21:12:27 domoticz kernel: [    0.773419] dwc_otg: FIQ enabled
Dec 27 21:12:27 domoticz kernel: [    0.773423] dwc_otg: NAK holdoff enabled
Dec 27 21:12:27 domoticz kernel: [    0.773427] dwc_otg: FIQ split-transaction FSM enabled
Dec 27 21:12:27 domoticz kernel: [    0.773440] Module dwc_common_port init
Dec 27 21:12:27 domoticz kernel: [    0.773654] usbcore: registered new interface driver usb-storage
Dec 27 21:12:27 domoticz kernel: [    0.775105] mousedev: PS/2 mouse device common for all mice
Dec 27 21:12:27 domoticz kernel: [    0.777302] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
Dec 27 21:12:27 domoticz kernel: [    0.778894] bcm2835-cpufreq: min=600000 max=1200000
Dec 27 21:12:27 domoticz kernel: [    0.780631] sdhci: Secure Digital Host Controller Interface driver
Dec 27 21:12:27 domoticz kernel: [    0.781980] sdhci: Copyright(c) Pierre Ossman
Dec 27 21:12:27 domoticz kernel: [    0.783559] sdhost-bcm2835 3f202000.sdhost: could not get clk, deferring probe
Dec 27 21:12:27 domoticz kernel: [    0.787123] mmc-bcm2835 3f300000.mmc: could not get clk, deferring probe
Dec 27 21:12:27 domoticz kernel: [    0.788642] sdhci-pltfm: SDHCI platform and OF driver helper
Dec 27 21:12:27 domoticz kernel: [    0.792679] ledtrig-cpu: registered to indicate activity on CPUs
Dec 27 21:12:27 domoticz kernel: [    0.794296] hidraw: raw HID events driver (C) Jiri Kosina
Dec 27 21:12:27 domoticz kernel: [    0.795907] usbcore: registered new interface driver usbhid
Dec 27 21:12:27 domoticz kernel: [    0.797338] usbhid: USB HID core driver
Dec 27 21:12:27 domoticz kernel: [    0.799562] vchiq: vchiq_init_state: slot_zero = 0xbdd80000, is_master = 0
Dec 27 21:12:27 domoticz kernel: [    0.802307] [vc_sm_connected_init]: start
Dec 27 21:12:27 domoticz kernel: [    0.805755] vc_vchi_sm_init: failed to open VCHI service (-1)
Dec 27 21:12:27 domoticz kernel: [    0.805854] [vc_sm_connected_init]: failed to initialize shared memory service
Dec 27 21:12:27 domoticz kernel: [    0.808797] [vc_sm_connected_init]: end - returning -1
Dec 27 21:12:27 domoticz kernel: [    0.810708] Initializing XFRM netlink socket
Dec 27 21:12:27 domoticz kernel: [    0.812256] NET: Registered protocol family 17
Dec 27 21:12:27 domoticz kernel: [    0.813912] Key type dns_resolver registered
Dec 27 21:12:27 domoticz kernel: [    0.815800] Registering SWP/SWPB emulation handler
Dec 27 21:12:27 domoticz kernel: [    0.818025] registered taskstats version 1
Dec 27 21:12:27 domoticz kernel: [    0.824815] uart-pl011 3f201000.serial: cts_event_workaround enabled
Dec 27 21:12:27 domoticz kernel: [    0.826406] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
Dec 27 21:12:27 domoticz kernel: [    0.831073] sdhost: log_buf @ bdd07000 (fdd07000)
Dec 27 21:12:27 domoticz kernel: [    0.910624] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
Dec 27 21:12:27 domoticz kernel: [    0.914335] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
Dec 27 21:12:27 domoticz kernel: [    0.915839] mmc-bcm2835 3f300000.mmc: DMA channel allocated
Dec 27 21:12:27 domoticz kernel: [    0.987418] mmc0: host does not support reading read-only switch, assuming write-enable
Dec 27 21:12:27 domoticz kernel: [    0.990719] of_cfs_init
Dec 27 21:12:27 domoticz kernel: [    0.990779] Indeed it is in host mode hprt0 = 00021501
Dec 27 21:12:27 domoticz kernel: [    0.993836] of_cfs_init: OK
Dec 27 21:12:27 domoticz kernel: [    0.995709] Waiting for root device PARTUUID=e80766f2-02...
Dec 27 21:12:27 domoticz kernel: [    1.051010] mmc0: new high speed SDHC card at address 0001
Dec 27 21:12:27 domoticz kernel: [    1.056145] mmcblk0: mmc0:0001 00000 14.9 GiB
Dec 27 21:12:27 domoticz kernel: [    1.058962]  mmcblk0: p1 p2
Dec 27 21:12:27 domoticz kernel: [    1.069058] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
Dec 27 21:12:27 domoticz kernel: [    1.072012] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
Dec 27 21:12:27 domoticz kernel: [    1.072437] random: fast init done
Dec 27 21:12:27 domoticz kernel: [    1.076238] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
Dec 27 21:12:27 domoticz kernel: [    1.080392] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
Dec 27 21:12:27 domoticz kernel: [    1.121517] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
Dec 27 21:12:27 domoticz kernel: [    1.124187] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
Dec 27 21:12:27 domoticz kernel: [    1.133254] devtmpfs: mounted
Dec 27 21:12:27 domoticz kernel: [    1.136413] Freeing unused kernel memory: 1024K
Dec 27 21:12:27 domoticz kernel: [    1.173457] mmc1: new high speed SDIO card at address 0001
Dec 27 21:12:27 domoticz kernel: [    1.190641] usb 1-1: new high-speed USB device number 2 using dwc_otg
Dec 27 21:12:27 domoticz kernel: [    1.192168] Indeed it is in host mode hprt0 = 00001101
Dec 27 21:12:27 domoticz kernel: [    1.420944] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
Dec 27 21:12:27 domoticz kernel: [    1.422402] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Dec 27 21:12:27 domoticz kernel: [    1.424675] hub 1-1:1.0: USB hub found
Dec 27 21:12:27 domoticz kernel: [    1.426166] hub 1-1:1.0: 5 ports detected
Dec 27 21:12:27 domoticz kernel: [    1.694677] NET: Registered protocol family 10
Dec 27 21:12:27 domoticz kernel: [    1.706057] ip_tables: (C) 2000-2006 Netfilter Core Team
Dec 27 21:12:27 domoticz kernel: [    1.750624] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
Dec 27 21:12:27 domoticz kernel: [    1.881013] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
Dec 27 21:12:27 domoticz kernel: [    1.882603] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Dec 27 21:12:27 domoticz kernel: [    1.886946] smsc95xx v1.0.5
Dec 27 21:12:27 domoticz kernel: [    1.984610] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:d4:81:2a
Dec 27 21:12:27 domoticz kernel: [    2.353008] i2c /dev entries driver

pepson

Dec 27 21:12:27 domoticz kernel: [    2.675918] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
Dec 27 21:12:27 domoticz kernel: [    3.109172] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
Dec 27 21:12:27 domoticz kernel: [    3.407342] brcmfmac: F1 signature read @0x18000000=0x1541a9a6
Dec 27 21:12:27 domoticz kernel: [    3.413382] usbcore: registered new interface driver brcmfmac
Dec 27 21:12:27 domoticz kernel: [    3.601930] brcmfmac: Firmware version = wl0: Aug  7 2017 00:46:29 version 7.45.41.46 (r666254 CY) FWID 01-f8a78378
Dec 27 21:12:27 domoticz kernel: [    3.602685] brcmfmac: brcmf_c_preinit_dcmds: CLM version = API: 12.2 Data: 7.11.15 Compiler: 1.24.2 ClmImport: 1.24.1 Creation: 2014-05-26 10:53:55 Inc Data: 9.10.41 Inc Compiler: 1.29.4 Inc ClmImport: 1.36.3 Creation: 2017-08-07 00:37:47 
Dec 27 21:12:27 domoticz avahi-daemon[327]: Successfully called chroot().
Dec 27 21:12:27 domoticz avahi-daemon[327]: Successfully dropped remaining capabilities.
Dec 27 21:12:27 domoticz avahi-daemon[327]: No service file found in /etc/avahi/services.
Dec 27 21:12:27 domoticz systemd[1]: Started Avahi mDNS/DNS-SD Stack.
Dec 27 21:12:27 domoticz systemd[1]: Reached target System Time Synchronized.
Dec 27 21:12:27 domoticz avahi-daemon[327]: Network interface enumeration completed.
Dec 27 21:12:27 domoticz avahi-daemon[327]: Server startup complete. Host name is domoticz.local. Local service cookie is 87145466.
Dec 27 21:12:27 domoticz systemd[1]: apt-daily.timer: Adding 5h 31min 57.980339s random time.
Dec 27 21:12:27 domoticz systemd[1]: Started Daily apt download activities.
Dec 27 21:12:27 domoticz systemd[1]: apt-daily-upgrade.timer: Adding 2min 40.737204s random time.
Dec 27 21:12:27 domoticz systemd[1]: Started Daily apt upgrade and clean activities.
Dec 27 21:12:27 domoticz systemd[1]: Reached target Timers.
Dec 27 21:12:27 domoticz systemd[1]: Started triggerhappy global hotkey daemon.
Dec 27 21:12:27 domoticz systemd[1]: Started System Logging Service.
Dec 27 21:12:27 domoticz systemd[1]: Started Save/Restore Sound Card State.
Dec 27 21:12:27 domoticz dhcpcd[339]: wlan0: starting wpa_supplicant
Dec 27 21:12:27 domoticz dhcpcd-run-hooks[374]: wlan0: starting wpa_supplicant
Dec 27 21:12:27 domoticz systemd[1]: Started Login Service.
Dec 27 21:12:27 domoticz dphys-swapfile[329]: Starting dphys-swapfile swapfile setup ...
Dec 27 21:12:27 domoticz raspi-config[330]: Checking if shift key is held down:Error opening '/dev/input/event*': No such file or directory
Dec 27 21:12:27 domoticz raspi-config[330]:  No. Switching to ondemand scaling governor.
Dec 27 21:12:27 domoticz systemd[1]: Started LSB: Switch to ondemand cpu governor (unless shift key is pressed).
Dec 27 21:12:27 domoticz OWFS[375]: DEFAULT: owlib.c:(208) Cannot open USB bus master
Dec 27 21:12:27 domoticz OWFS[375]: DEFAULT: owlib.c:(52) No valid 1-wire buses found
Dec 27 21:12:27 domoticz systemd[1]: start1wire.service: Control process exited, code=exited status=1
Dec 27 21:12:27 domoticz systemd[1]: Failed to start LSB: Start OWFS at boot time.
Dec 27 21:12:27 domoticz systemd[1]: start1wire.service: Unit entered failed state.
Dec 27 21:12:27 domoticz systemd[1]: start1wire.service: Failed with result 'exit-code'.
Dec 27 21:12:27 domoticz dphys-swapfile[329]: want /var/swap=100MByte, checking existing: keeping it
Dec 27 21:12:27 domoticz kernel: [    4.979888] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Dec 27 21:12:27 domoticz kernel: [    4.979897] brcmfmac: power management disabled
Dec 27 21:12:27 domoticz kernel: [    4.987898] Adding 102396k swap on /var/swap.  Priority:-1 extents:1 across:102396k SSFS
Dec 27 21:12:27 domoticz dphys-swapfile[329]: done.
Dec 27 21:12:27 domoticz systemd[1]: Started LSB: Autogenerate and use a swap file.
Dec 27 21:12:27 domoticz dhcpcd[339]: eth0: waiting for carrier
Dec 27 21:12:27 domoticz dhcpcd[339]: wlan0: waiting for carrier
Dec 27 21:12:27 domoticz dhcpcd[339]: wlan0: carrier acquired
Dec 27 21:12:27 domoticz kernel: [    5.321930] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
Dec 27 21:12:27 domoticz kernel: [    5.322223] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Dec 27 21:12:27 domoticz dhcpcd[339]: DUID 00:01:00:01:21:b0:d9:d9:b8:27:eb:81:d4:7f
Dec 27 21:12:27 domoticz dhcpcd[339]: wlan0: IAID eb:81:d4:7f
Dec 27 21:12:27 domoticz dhcpcd[339]: wlan0: adding address fe80::6bd:3cc7:2b64:c842
Dec 27 21:12:27 domoticz dhcpcd[339]: wlan0: carrier lost
Dec 27 21:12:28 domoticz dhcpcd[339]: wlan0: deleting address fe80::6bd:3cc7:2b64:c842
Dec 27 21:12:29 domoticz dhcpcd[339]: eth0: carrier acquired
Dec 27 21:12:29 domoticz kernel: [    6.725223] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Dec 27 21:12:29 domoticz kernel: [    6.726375] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
Dec 27 21:12:29 domoticz dhcpcd[339]: eth0: IAID eb:d4:81:2a
Dec 27 21:12:29 domoticz dhcpcd[339]: eth0: adding address fe80::7a80:6e8f:27f0:4005
Dec 27 21:12:29 domoticz dhcpcd[339]: eth0: probing address 192.168.13.5/24
Dec 27 21:12:29 domoticz dhcpcd[339]: eth0: soliciting an IPv6 router
Dec 27 21:12:30 domoticz avahi-daemon[327]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::7a80:6e8f:27f0:4005.
Dec 27 21:12:30 domoticz avahi-daemon[327]: New relevant interface eth0.IPv6 for mDNS.
Dec 27 21:12:30 domoticz avahi-daemon[327]: Registering new address record for fe80::7a80:6e8f:27f0:4005 on eth0.*.
Dec 27 21:12:34 domoticz dhcpcd[339]: eth0: using static address 192.168.13.5/24
Dec 27 21:12:34 domoticz dhcpcd[339]: eth0: adding route to 192.168.13.0/24
Dec 27 21:12:34 domoticz dhcpcd[339]: eth0: adding default route via 192.168.13.1
Dec 27 21:12:34 domoticz avahi-daemon[327]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.13.5.
Dec 27 21:12:34 domoticz avahi-daemon[327]: New relevant interface eth0.IPv4 for mDNS.
Dec 27 21:12:34 domoticz avahi-daemon[327]: Registering new address record for 192.168.13.5 on eth0.IPv4.
Dec 27 21:12:34 domoticz dhcpcd[339]: forked to background, child pid 470
Dec 27 21:12:34 domoticz systemd[1]: Started dhcpcd on all interfaces.
Dec 27 21:12:34 domoticz systemd[1]: Reached target Network.
Dec 27 21:12:34 domoticz systemd[1]: Reached target Network is Online.
Dec 27 21:12:34 domoticz systemd[1]: Starting LSB: Home Automation System...
Dec 27 21:12:34 domoticz systemd[1]: Starting /etc/rc.local Compatibility...
Dec 27 21:12:34 domoticz systemd[1]: Starting Permit User Sessions...
Dec 27 21:12:34 domoticz systemd[1]: Starting OpenBSD Secure Shell server...
Dec 27 21:12:34 domoticz systemd[1]: Started /etc/rc.local Compatibility.
Dec 27 21:12:34 domoticz systemd[1]: Started Permit User Sessions.
Dec 27 21:12:34 domoticz systemd[1]: Starting Hold until boot process finishes up...
Dec 27 21:12:34 domoticz systemd[1]: Starting Terminate Plymouth Boot Screen...
Dec 27 21:12:34 domoticz systemd[1]: Received SIGRTMIN+21 from PID 190 (plymouthd).
Dec 27 21:12:34 domoticz systemd[1]: Started Hold until boot process finishes up.
Dec 27 21:12:34 domoticz systemd[1]: Started Terminate Plymouth Boot Screen.
Dec 27 21:12:34 domoticz systemd[1]: Started Getty on tty1.
Dec 27 21:12:34 domoticz systemd[1]: Reached target Login Prompts.
Dec 27 21:12:34 domoticz systemd[1]: Started OpenBSD Secure Shell server.
Dec 27 21:12:35 domoticz domoticz.sh[471]: 2017-12-27 21:12:35.467  Domoticz V3.8796 (c)2012-2017 GizMoCuz
Dec 27 21:12:35 domoticz domoticz.sh[471]: 2017-12-27 21:12:35.467  Build Hash: 2d99bbbc, Date: 2017-12-24 07:06:53
Dec 27 21:12:35 domoticz domoticz.sh[471]: 2017-12-27 21:12:35.468  Startup Path: /home/pi/domoticz/
Dec 27 21:12:35 domoticz domoticz.sh[471]: domoticz: Domoticz is starting up....
Dec 27 21:12:35 domoticz domoticz: Domoticz is starting up....
Dec 27 21:12:35 domoticz domoticz: Domoticz running...
Dec 27 21:12:35 domoticz systemd[1]: Started LSB: Home Automation System.
Dec 27 21:12:35 domoticz systemd[1]: Reached target Multi-User System.
Dec 27 21:12:35 domoticz systemd[1]: Reached target Graphical Interface.
Dec 27 21:12:35 domoticz systemd[1]: Starting Update UTMP about System Runlevel Changes...
Dec 27 21:12:35 domoticz systemd[1]: Started Update UTMP about System Runlevel Changes.
Dec 27 21:12:35 domoticz systemd[1]: Startup finished in 1.510s (kernel) + 11.498s (userspace) = 13.009s.
Dec 27 21:12:38 domoticz kernel: [   15.710546] uart-pl011 3f201000.serial: no DMA platform data
Dec 27 21:12:42 domoticz dhcpcd[470]: eth0: no IPv6 Routers available
Dec 27 21:12:53 domoticz systemd[1]: Created slice User Slice of pi.
Dec 27 21:12:53 domoticz systemd[1]: Starting User Manager for UID 1000...
Dec 27 21:12:53 domoticz systemd[1]: Started Session c1 of user pi.
Dec 27 21:12:53 domoticz systemd[535]: Listening on GnuPG cryptographic agent and passphrase cache (restricted).
Dec 27 21:12:53 domoticz systemd[535]: Listening on GnuPG cryptographic agent and passphrase cache.
Dec 27 21:12:53 domoticz systemd[535]: Listening on GnuPG cryptographic agent (access for web browsers).
Dec 27 21:12:53 domoticz systemd[535]: Reached target Paths.
Dec 27 21:12:53 domoticz systemd[535]: Listening on GnuPG cryptographic agent (ssh-agent emulation).
Dec 27 21:12:53 domoticz systemd[535]: Reached target Sockets.
Dec 27 21:12:53 domoticz systemd[535]: Reached target Timers.
Dec 27 21:12:53 domoticz systemd[535]: Reached target Basic System.
Dec 27 21:12:53 domoticz systemd[535]: Reached target Default.
Dec 27 21:12:53 domoticz systemd[535]: Startup finished in 48ms.
Dec 27 21:12:53 domoticz systemd[1]: Started User Manager for UID 1000.
Dec 27 21:13:03 domoticz systemd[535]: Time has been changed
Dec 27 21:13:03 domoticz systemd[1]: Time has been changed
Dec 27 21:13:03 domoticz systemd-timesyncd[285]: Synchronized to time server 195.189.85.132:123 (2.debian.pool.ntp.org).
Dec 27 21:13:03 domoticz systemd[1]: apt-daily.timer: Adding 8h 6min 59.681187s random time.
Dec 27 21:13:03 domoticz systemd[1]: apt-daily-upgrade.timer: Adding 32min 42.364143s random time.```

mfalkvidd

@pepson ok, so mysgw does at least log to syslog, as seen here

Dec 27 21:12:27 domoticz mysgw: Starting gateway...
Dec 27 21:12:27 domoticz mysgw: Protocol version - 2.2.0-rc.2

but nothing else. I expected there to be more information, but maybe I'm just not familiar enough with the raspberry pi gateway.

pepson

Yes but only one time read and then start the problem.

gohan

Can you try building the ethernet gateway instead?

pepson

Ethernet work ok. But i better want serial and found bug and solution why not working serial...

gohan

I just wanted to make sure at least it was working OK as ethernet.

pepson

Problem is only on serial...

pepson

Please help...

zboblamont

@pepson Just a suggestion, but are you sure the Pi3 is looking at ttyUSB1, ie have you confirmed this is the Gateway serial connection ?
I am using direct serial connection to the pi3 GPIO as ttySO with Domoticz, but when I tried a USB Gateway at one point, the connection was NOT working using the expected ttyUSB quoted. I had to check the tty connections via Putty to establish the actual link...

pepson

But can you give me commend to build it as you use ttySO ?

pepson

I build it as ttySO
./configure --my-transport=rfm69 --my-rfm69-frequency=868 --my-is-rfm69hw --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttySO

and i have and info:

2017-12-28 15:40:21.822 MySensors: Using serial port: /dev/ttyS0
2017-12-28 15:40:21.832 Error: MySensors: Error opening serial port!

pepson

Then build as /dev/serial0 and the same problem. This is show in log Domoticz. One read version and port closed.

2017-12-28 15:48:14.418 MySensors: Using serial port: /dev/serial0
2017-12-28 15:48:14.418 MySensors: Gateway Version: 2.2.0-rc.2
2017-12-28 15:48:14.418 Error: Serial Port closed!... Error: End of file
2017-12-28 15:48:15.418 MySensors: retrying in 30 seconds...

mfalkvidd

@pepson could you post your hardware settings in Domoticz? This is what works for me:
0_1514474366659_66d2b11b-dcc4-46ec-83e3-767278ec3e1f-image.png

Could you also try building the gateway without rfm69 support, to check if the problem is generic or related to rfm69. Use this:

./configure --my-transport=none --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB42
make && sudo ./bin/mysgw -d

pepson

Hello
Thanks for your help. I start from beginning build DOmoticz on my RPi3 with clean latest image. After run in Sudo raspi-config i enable SPI and Serial , then install DOmoticz and now all works OK. Then build Mysensor Gateway and all is ok with no error in Domoticz. Works on /dev/ttyUSB42

pepson

But how i can build MySensors Gateway on serial with radio RFM69HW but on old version 2.1.1 ?

pepson

And have next problem... i build sketch on version 2.2.0-rc2 but after write to Arduino Mini Pro he is not connected to my Gateway on RPI3.

This is sketch. What is wrong ?

/*
   Relay with button sketch
   modified to work with no uplink
   to gateway and try to maintain sync to controller
*/


#define MY_DEBUG                               // Enable debug prints to serial monitor

#define MY_RADIO_RFM69
#define MY_RFM69_FREQUENCY 868
#define MY_IS_RFM69HW
#define MY_RFM69_NEW_DRIVER

//#define MY_NODE_ID 203                       // Node id defaults to AUTO (tries to fetch id from controller) 

#define MY_TRANSPORT_WAIT_READY_MS 5000        //set how long to wait for transport ready in milliseconds

#define MY_REPEATER_FEATURE                    // Enabled repeater feature for this node

#include <MySensors.h>
#include <Bounce2.h>

#define RELAY_PIN  5      // Arduino Digital I/O pin number for relay 
#define BUTTON_PIN  3     // Arduino Digital I/O pin number for button 
#define CHILD_ID 1        // Id of the sensor child
#define RELAY_ON 1
#define RELAY_OFF 0

Bounce debouncer = Bounce();
int oldValue = 0;
bool uplinkAvailable = true;
bool state = false;
bool requestState;
bool firstStart = true;
unsigned long uplinkCheckTime ;                // holder for uplink checks
unsigned long uplinkCheckPeriod = 30*1000;     // time between checks for uplink in milliseconds
unsigned long returnWait = 1000;               // how long to wait for return from controller in milliseconds.. adjust as needed
unsigned long oldTime = 0;
unsigned long newTime = 0;
MyMessage msg(CHILD_ID, V_STATUS);

void setup(){
  pinMode(BUTTON_PIN, INPUT_PULLUP);           // Setup the button pin, Activate internal pull-up
  
  debouncer.attach(BUTTON_PIN);                // After setting up the button, setup debouncer
  debouncer.interval(5);

  pinMode(RELAY_PIN, OUTPUT);                 // set relay pin in output mode
  digitalWrite(RELAY_PIN, RELAY_OFF);         // Make sure relay is off when starting up
}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("1xRelay & Button", "2.2.0-rc2");

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_BINARY);
}


void loop(){
  if (firstStart) {                            // this code is only run once at startup
    Serial.println("First run started");
    requestTime();                             // get time from controller
    wait (returnWait);                         // delay to allow time to return
    if (oldTime == 0){                         // check to see if there was a return from the time request
      Serial.println("uplink not available");
      uplinkAvailable = false;                 // no uplink established
      uplinkCheckTime = millis();
    }
     else{
      Serial.println("uplink available");
      request( CHILD_ID, V_STATUS);            // get status of switch on controller
      wait (returnWait);                       //wait needed to allow request to return from controller
      Serial.print("controller state --- ");
      Serial.println(requestState);
      if (requestState != state) {             // check that controller is corectly showing the current relay state
        send(msg.set(state), false);           // notify controller of current state
      } 
     }   
  firstStart = false;                                          // set firstStart flag false to prevent code from running again
 }

  debouncer.update();
  int value = debouncer.read();                               // Get the update value
  if (value != oldValue && value == 0) {                      // check for new button push
    state =  !state;                                          // Toggle the state
    digitalWrite(RELAY_PIN, state ? RELAY_ON : RELAY_OFF);    // switch the relay to the new state
    requestTime();
    wait (returnWait);                                               // delay to allow time to return
    if (oldTime != newTime){                                  // if times are different then uplink is available
      send(msg.set(state), false);
      oldTime = newTime;
    }
    else{                                                    // if times are the same no uplink is available
     Serial.println("uplink not available");
      uplinkAvailable = false;                                // no uplink available, set flag false
      uplinkCheckTime = millis();                             // start the timer from now
    }

  }
  oldValue = value;
 
  if (!uplinkAvailable && (millis() - uplinkCheckTime > uplinkCheckPeriod) ) {       // test to see if function should be called
    uplinkCheck();                                                                  // call uplink checking function
  }

}

/*-------------------start of functions--------------------------*/

void receive(const MyMessage &message) {
  if (message.type == V_STATUS) {                                   // check to see if incoming message is for a switch
    switch (message.getCommand()) {                                 // message.getCommand will give us the command type of the incomming message
      case C_SET:                                                   //message is a set command  from controller to update relay state
        state = message.getBool();                                  // get the new state
        digitalWrite(RELAY_PIN, state ? RELAY_ON : RELAY_OFF);      // switch relay to new state
        uplinkAvailable = true;                                     //  uplink established
        /*---- Write some debug info----*/
        Serial.print("Incoming change for sensor:");
        Serial.print(message.sensor);
        Serial.print(", New status: ");
        Serial.println(message.getBool());
        break;
      case C_REQ:                                               // message is a returning request from controller
        requestState = message.getBool();                       // update requestState with returning state
        break;
    }
  }
}

void uplinkCheck() {
    requestTime();
    wait (returnWait);                       // wait for time return.. this may need to be varied for your system
   if (oldTime != newTime){
     Serial.println("uplink re-established");
     request( CHILD_ID, V_STATUS);
     wait (returnWait);                        //wait needed to allow request to return from controller
    if (requestState != state) {              // check that controller is corectly showing the current relay state
      send(msg.set(state), false);            // notify controller of current state no ack
      uplinkAvailable = true;                 //  uplink established
      oldTime = newTime;
    }
  }
  uplinkCheckTime = millis();                // reset the checktime
  Serial.println("uplinkchecktime reset");
}


void receiveTime(unsigned long time)
{
  if (firstStart){
    oldTime = time;
    newTime = time;
  }
  else{
  newTime = time;
}
  Serial.print("time received---- " );
  Serial.println(time);
}```

zboblamont

@pepson Try walking in little steps trying each stage rather than running into new walls then expressing surprise at broken nose, no offence intended
Gateway and nodes, same platform, same version..... Otherwise they are speaking Chinese and Swedish hoping for somebody to explain the meaning of fubar...

pepson

I use the same version now 2.2.0-rc2 but when i programmed sketch to node it not connection to Gateway... That i want come back to version 2.1.1 gateway but i dont know how ? Or resolved problem Node 2.2.0-rc2 i stay on this.

But when run debug gateway show this:


pi@domoticz:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-rc.2
mysgw: MCO:BGN:INIT GW,CP=RPNGL---,VER=2.2.0-rc.2
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: !TSF:SAN:FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:DIS
mysgw: TSF:TDI:TSL
mysgw: TSM:FAIL:RE-INIT
mysgw: TSM:INIT
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE

This is sketch 2.2.0-rc2

/*
   Relay with button sketch
   modified to work with no uplink
   to gateway and try to maintain sync to controller
*/


#define MY_DEBUG                               // Enable debug prints to serial monitor

#define MY_RADIO_RFM69
#define RFM69_868MHZ
#define MY_IS_RFM69HW
#define MY_RFM69_NEW_DRIVER

//#define MY_NODE_ID 203                       // Node id defaults to AUTO (tries to fetch id from controller) 

#define MY_TRANSPORT_WAIT_READY_MS 5000        //set how long to wait for transport ready in milliseconds

#define MY_REPEATER_FEATURE                    // Enabled repeater feature for this node

#include <MySensors.h>
#include <Bounce2.h>

#define RELAY_PIN  5      // Arduino Digital I/O pin number for relay 
#define BUTTON_PIN  3     // Arduino Digital I/O pin number for button 
#define CHILD_ID 1        // Id of the sensor child
#define RELAY_ON 1
#define RELAY_OFF 0

Bounce debouncer = Bounce();
int oldValue = 0;
bool uplinkAvailable = true;
bool state = false;
bool requestState;
bool firstStart = true;
unsigned long uplinkCheckTime ;                // holder for uplink checks
unsigned long uplinkCheckPeriod = 30*1000;     // time between checks for uplink in milliseconds
unsigned long returnWait = 1000;               // how long to wait for return from controller in milliseconds.. adjust as needed
unsigned long oldTime = 0;
unsigned long newTime = 0;
MyMessage msg(CHILD_ID, V_STATUS);

void setup(){
  pinMode(BUTTON_PIN, INPUT_PULLUP);           // Setup the button pin, Activate internal pull-up
  
  debouncer.attach(BUTTON_PIN);                // After setting up the button, setup debouncer
  debouncer.interval(5);

  pinMode(RELAY_PIN, OUTPUT);                 // set relay pin in output mode
  digitalWrite(RELAY_PIN, RELAY_OFF);         // Make sure relay is off when starting up
}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("1xRelay & Button", "2.2.0-rc2");

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_BINARY);
}


void loop(){
  if (firstStart) {                            // this code is only run once at startup
    Serial.println("First run started");
    requestTime();                             // get time from controller
    wait (returnWait);                         // delay to allow time to return
    if (oldTime == 0){                         // check to see if there was a return from the time request
      Serial.println("uplink not available");
      uplinkAvailable = false;                 // no uplink established
      uplinkCheckTime = millis();
    }
     else{
      Serial.println("uplink available");
      request( CHILD_ID, V_STATUS);            // get status of switch on controller
      wait (returnWait);                       //wait needed to allow request to return from controller
      Serial.print("controller state --- ");
      Serial.println(requestState);
      if (requestState != state) {             // check that controller is corectly showing the current relay state
        send(msg.set(state), false);           // notify controller of current state
      } 
     }   
  firstStart = false;                                          // set firstStart flag false to prevent code from running again
 }

  debouncer.update();
  int value = debouncer.read();                               // Get the update value
  if (value != oldValue && value == 0) {                      // check for new button push
    state =  !state;                                          // Toggle the state
    digitalWrite(RELAY_PIN, state ? RELAY_ON : RELAY_OFF);    // switch the relay to the new state
    requestTime();
    wait (returnWait);                                               // delay to allow time to return
    if (oldTime != newTime){                                  // if times are different then uplink is available
      send(msg.set(state), false);
      oldTime = newTime;
    }
    else{                                                    // if times are the same no uplink is available
     Serial.println("uplink not available");
      uplinkAvailable = false;                                // no uplink available, set flag false
      uplinkCheckTime = millis();                             // start the timer from now
    }

  }
  oldValue = value;
 
  if (!uplinkAvailable && (millis() - uplinkCheckTime > uplinkCheckPeriod) ) {       // test to see if function should be called
    uplinkCheck();                                                                  // call uplink checking function
  }

}

/*-------------------start of functions--------------------------*/

void receive(const MyMessage &message) {
  if (message.type == V_STATUS) {                                   // check to see if incoming message is for a switch
    switch (message.getCommand()) {                                 // message.getCommand will give us the command type of the incomming message
      case C_SET:                                                   //message is a set command  from controller to update relay state
        state = message.getBool();                                  // get the new state
        digitalWrite(RELAY_PIN, state ? RELAY_ON : RELAY_OFF);      // switch relay to new state
        uplinkAvailable = true;                                     //  uplink established
        /*---- Write some debug info----*/
        Serial.print("Incoming change for sensor:");
        Serial.print(message.sensor);
        Serial.print(", New status: ");
        Serial.println(message.getBool());
        break;
      case C_REQ:                                               // message is a returning request from controller
        requestState = message.getBool();                       // update requestState with returning state
        break;
    }
  }
}

void uplinkCheck() {
    requestTime();
    wait (returnWait);                       // wait for time return.. this may need to be varied for your system
   if (oldTime != newTime){
     Serial.println("uplink re-established");
     request( CHILD_ID, V_STATUS);
     wait (returnWait);                        //wait needed to allow request to return from controller
    if (requestState != state) {              // check that controller is corectly showing the current relay state
      send(msg.set(state), false);            // notify controller of current state no ack
      uplinkAvailable = true;                 //  uplink established
      oldTime = newTime;
    }
  }
  uplinkCheckTime = millis();                // reset the checktime
  Serial.println("uplinkchecktime reset");
}


void receiveTime(unsigned long time)
{
  if (firstStart){
    oldTime = time;
    newTime = time;
  }
  else{
  newTime = time;
}
  Serial.print("time received---- " );
  Serial.println(time);
}```

zboblamont

@pepson Let's try the baby steps I referred to earlier.

The current stable version of MySensors is 2.1. Those using 2.2 tend to be experienced people versed in programming and experimenting and problem solving, hence it is not an official release.... yet you are using it and asking for solutions... Hello ?

I am and have been for the last few months using a Pro-Mini with RFM69 as nodes and gateway using 2.1 attached to a Pi3 running Domoticz.... No problems, but slowly coming to understand most of what I am doing...

I am still on baby steps, I don't mind at all, it works.....

pepson

Ok but i dont know how build Gateway on version 2.1.1 because when i do step by step as show on mysensors.org it default build me version gateway 2.2.0-rc2

zboblamont

@pepson As in this page? 2.1.1 - Latest Release ?
https://www.mysensors.org/download

pepson

I found bug in Domoticz BETA 8796. No reconized version gateway in HARDWARE. On stable 8153 works with no problem and correct reconized version gateway 2.2.0-rc2...
And again problem with this:
CODE: SELECT ALL

2017-12-28 20:01:32.587 MySensors: retrying in 30 seconds...
2017-12-28 20:02:08.752 MySensors: Using serial port: /dev/serial0
2017-12-28 20:02:08.752 MySensors: Gateway Version: 2.2.0-rc.2
2017-12-28 20:02:08.752 Error: Serial Port closed!... Error: End of file
2017-12-28 20:02:09.752 MySensors: retrying in 30 seconds...
2017-12-28 20:02:38.755 MySensors: Using serial port: /dev/serial0
2017-12-28 20:02:38.755 Error: Serial Port closed!... Error: End of file
2017-12-28 20:02:39.755 MySensors: retrying in 30 seconds...
2017-12-28 20:03:08.757 MySensors: Using serial port: /dev/serial0
2017-12-28 20:03:08.761 Error: Serial Port closed!... Error: End of file
2017-12-28 20:03:09.758 MySensors: retrying in 30 seconds...
On beta is problem.
On stable works correct.

pepson

This post is deleted!

pepson

@macvictor said in Building a Raspberry Pi Gateway:

@marceloaqno Thank's for you help. I have other question.. general I try configure my gateway to work with security & signing, but they doesn't work. Where is problem? On the bottom i send point what it do it:

Gateway:

./configure --my-gateway=mqtt --my-controller-ip-address=127.0.0.1 --my-mqtt-publish-topic-prefix=mysensors-out --my-mqtt-subscribe-topic-prefix=mysensors-in --my-mqtt-client-id=mygateway1 --my-mqtt-password=PASS --my-mqtt-user=USER --my-rf24-encryption-enabled --my-signing=software --my-signing-request-signatures --my-signing-request-gw-signatures-from-all
make
sudo make install
sudo systemctl enable mysgw.service
sudo systemctl start mysgw.service
sudo mysgw --gen-soft-hmac-key
sudo mysgw --set-soft-hmac-key=02417628BC1573CC380...
sudo mysgw --gen-soft-serial-key
sudo mysgw --set-soft-serial-key=00762CD152B868F7EB
sudo mysgw --gen-aes-key
sudo mysgw --set-aes-key= A790AD78B2D8B4DBBB5B2C4B9DD6DAF3

Node:

Load script SecurityPersonalizer.ino
Uncomment and send sketch to arduino

#define USE_SOFT_SIGNING
#define STORE_SOFT_KEY
#define USER_SOFT_KEY
#define STORE_SOFT_SERIAL
#define STORE_AES_KEY
#define USER_AES_KEY

#define MY_SOFT_HMAC_KEY 0X2,0X41,0X76,0X28,0XBC,0X15,0X73,0XCC,0X38...
#define MY_AES_KEY 0XA7,0X90,0XAD,0X78,0XB2,0XD8...

Read all value from EPROM (test save):

Personalization sketch for MySensors usage.
-------------------------------------------
EEPROM configuration:
SOFT_HMAC_KEY | 02417628BC1573CC380DE0FADF7C87D7D3C77272A783E6E438786A07C3A8C6CF
SOFT_SERIAL   | 39BB1370C289643251
AES_KEY       | A790AD78B2D8B4DBBB5B2C4B9DD6DAF3
--------------------------------
Personalization is now complete.

Send sample sketch to arduino:

//!< Enable debug prints to serial monitor
#define MY_DEBUG
//!< Enable signing related debug prints to serial monitor
#define MY_DEBUG_VERBOSE_SIGNING
// Enable NRF24L01 radio type
#define MY_RADIO_NRF24

// Select soft signing
#define MY_SIGNING_SOFT

// Enable lockdown of node if suspicious activity is detected
//-->> #define MY_NODE_LOCK_FEATURE

// Enable node whitelisting
//#define MY_SIGNING_NODE_WHITELISTING {{.nodeId = GATEWAY_ADDRESS,.serial = {0x09,0x08,0x07,0x06,0x05,0x04,0x03,0x02,0x01}}}

// Enable this if you want destination node to sign all messages sent to this node.
#define MY_SIGNING_REQUEST_SIGNATURES

// SETTINGS FOR MY_SIGNING_SOFT
#define MY_SIGNING_SOFT_RANDOMSEED_PIN 7 //!< Unconnected analog pin for random seed

// Add repeater function to this sensor
#define MY_REPEATER_FEATURE


#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define RELAY_PIN  4    // Arduino Digital I/O pin number for relay 
#define BUTTON_PIN  3   // Arduino Digital I/O pin number for button 
#define CHILD_ID 1      // Id of the sensor child
#define RELAY_ON 1
#define RELAY_OFF 0

Bounce debouncer = Bounce();
int oldValue = 0;
bool state;

MyMessage msg(CHILD_ID, V_LIGHT);

void setup()
{
  // Setup the button
  pinMode(BUTTON_PIN, INPUT);
  // Activate internal pull-up
  digitalWrite(BUTTON_PIN, HIGH);

  // After setting up the button, setup debouncer
  debouncer.attach(BUTTON_PIN);
  debouncer.interval(5);

  // Make sure relays are off when starting up
  digitalWrite(RELAY_PIN, RELAY_OFF);
  // Then set relay pins in output mode
  pinMode(RELAY_PIN, OUTPUT);

  // Set relay to last known state (using eeprom storage)
  state = loadState(CHILD_ID);
  digitalWrite(RELAY_PIN, state ? RELAY_ON : RELAY_OFF);
}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Relay & Button", "1.0");
  
  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_LIGHT, "Switch Secure Sensor", false);
}

/*
   Example on how to asynchronously check for new messages from gw
*/
void loop()
{
  debouncer.update();
  // Get the update value
  int value = debouncer.read();
//  if (value != oldValue && value == 0) {
    send(msg.set(state ? false : true), true); // Send new state and request ack back
//  }
//  oldValue = value;
  delay(5000);
}

void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.isAck()) {
    Serial.println("This is an ack from gateway");
  }

  if (message.type == V_LIGHT) {
    // Change relay state
    state = message.getBool();
    digitalWrite(RELAY_PIN, state ? RELAY_ON : RELAY_OFF);
    // Store state in eeprom
    // saveState(CHILD_ID, state);

    // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.print(message.sensor);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
  }
}

And finally in Arduino Serial Monitor I see:

0 MCO:BGN:INIT REPEATER,CP=RNNRAS-,VER=2.1.1
4 TSM:INIT
5 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
13 TSF:SID:OK,ID=105
15 TSM:FPAR
16 Will not sign message for destination 255 as it does not require it
58 TSF:MSG:SEND,105-105-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2065 !TSM:FPAR:NO REPLY
2067 TSM:FPAR
2068 Will not sign message for destination 255 as it does not require it
2110 TSF:MSG:SEND,105-105-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4117 !TSM:FPAR:NO REPLY
4119 TSM:FPAR
4120 Will not sign message for destination 255 as it does not require it
4162 TSF:MSG:SEND,105-105-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6169 !TSM:FPAR:NO REPLY
6171 TSM:FPAR
6172 Will not sign message for destination 255 as it does not require it
6214 TSF:MSG:SEND,105-105-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8221 !TSM:FPAR:FAIL
8222 TSM:FAIL:CNT=1
8224 TSM:FAIL:PDT

and in gateway i see:

sudo mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG-S-,VER=2.1.1
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: Attempting MQTT connection...
mysgw: connected to 127.0.0.1
mysgw: MQTT connected
mysgw: Sending message on topic: mysensors-out/0/255/0/0/18
mysgw: TSF:MSG:READ,171-107-54,s=221,c=2,t=131,pt=4,l=25,sg=0:-1418183441
mysgw: !TSF:MSG:PVER,3=2
mysgw: TSF:MSG:READ,135-23-172,s=20,c=3,t=200,pt=7,l=25,sg=0:-0.00000178
mysgw: !TSF:MSG:PVER,1=2
mysgw: TSF:MSG:READ,34-66-89,s=168,c=1,t=9,pt=1,l=25,sg=0:56
mysgw: !TSF:MSG:PVER,1=2
mysgw: TSF:MSG:READ,223-46-240,s=112,c=5,t=192,pt=5,l=11,sg=1:1407647670
mysgw: TSF:MSG:REL MSG
mysgw: !TSF:RTE:240 UNKNOWN
mysgw: !TSF:MSG:SEND,223-0-240-240,s=112,c=5,t=192,pt=5,l=11,sg=1,ft=0,st=NACK:1407647670
mysgw: TSF:MSG:READ,183-139-129,s=37,c=6,t=155,pt=1,l=21,sg=0:48
mysgw: !TSF:MSG:PVER,0=2
mysgw: TSF:MSG:READ,139-214-233,s=61,c=3,t=193,pt=7,l=0,sg=1:0.00000000
mysgw: TSF:MSG:REL MSG
mysgw: !TSF:RTE:233 UNKNOWN
mysgw: !TSF:MSG:SEND,139-0-233-233,s=61,c=3,t=193,pt=7,l=0,sg=1,ft=0,st=NACK:0.00000000
mysgw: TSF:MSG:READ,83-33-7,s=179,c=2,t=27,pt=4,l=25,sg=1:-2057270722
mysgw: !TSF:MSG:PVER,3=2
mysgw: TSF:MSG:READ,110-148-67,s=113,c=0,t=158,pt=1,l=9,sg=1:251
mysgw: !TSF:MSG:PVER,1=2
mysgw: TSF:MSG:READ,75-209-102,s=204,c=7,t=25,pt=1,l=11,sg=1:52
mysgw: !TSF:MSG:PVER,0=2
mysgw: TSF:MSG:READ,184-209-235,s=58,c=1,t=140,pt=6,l=23,sg=1:1DC404A5401119FACF0000000000000000000000000000
mysgw: !TSF:MSG:PVER,3=2
mysgw: TSF:MSG:READ,172-203-51,s=140,c=2,t=173,pt=0,l=1,sg=1:?
mysgw: TSF:MSG:REL MSG
mysgw: !TSF:RTE:51 UNKNOWN
mysgw: !TSF:MSG:SEND,172-0-51-51,s=140,c=2,t=173,pt=0,l=1,sg=1,ft=0,st=NACK:?

Where is problem?

@macvictor
But how use itn on RFM69HW ? I dont see to be available #define MY_RFM69_ENABLE_ENCRYPTION... Only for #define MY_RF24_ENABLE_ENCRYPTION...

mfalkvidd

@pepson are you asking how to enable encryption on rfm69? (it is a bit unclear what you mean by "itn")

In that case, see https://www.mysensors.org/apidocs-beta/group__RFM69SettingGrpPub.html#ga17a7a919994e569f078e3787c2c4ecd2

pepson

@mfalkvidd

Yes Thanks

BTW
MySensors gateway as you see is problem with latest beta domoticz.

mfalkvidd

@pepson yes I saw that. Thanks for checking. Have you reported the problem to the Domoticz team?

pepson

@mfalkvidd
Yes write on forum Domoticz in section BUG

mfalkvidd

@pepson great!

The report is at https://www.domoticz.com/forum/viewtopic.php?f=6&t=21125&sid=e414507bb1ca4596e93cf885047275a9 in case someone needs to find it in the future.

ghiglie

Hello!
I'm trying to "make" on Alpine Linux in a Docker (ok, maybe it's useless, but way interesting!).

With a Debian image it's ok, but I'd like to use Alpine.

I get this error:

g++ -MT build/drivers/Linux/SPIDEV.o -MMD -MP -march=armv7-a -mtune=cortex-a7 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DSPI_SPIDEV_DEVICE=\"/dev/spidev0.0\"  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/SPIDEV.cpp -o build/drivers/Linux/SPIDEV.o
In file included from /usr/include/sys/ioctl.h:7:0,
                 from drivers/Linux/SPIDEV.cpp:27:
drivers/Linux/SPIDEV.cpp: In static member function 'static uint8_t SPIDEVClass::transfer(uint8_t)':
drivers/Linux/SPIDEV.cpp:153:18: error: '_IOC_SIZEBITS' was not declared in this scope
  ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr);
                  ^
drivers/Linux/SPIDEV.cpp: In static member function 'static void SPIDEVClass::transfernb(char*, char*, uint32_t)':
drivers/Linux/SPIDEV.cpp:175:18: error: '_IOC_SIZEBITS' was not declared in this scope
  ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr);
                  ^
make: *** [Makefile:99: build/drivers/Linux/SPIDEV.o] Error 1
root@local-mysgw-alpine:/opt/MySensors3$ make
g++ -MT build/drivers/Linux/SPIDEV.o -MMD -MP -march=armv7-a -mtune=cortex-a7 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DSPI_SPIDEV_DEVICE=\"/dev/spidev0.0\"  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/SPIDEV.cpp -o build/drivers/Linux/SPIDEV.o
eIn file included from /usr/include/sys/ioctl.h:7:0,
                 from drivers/Linux/SPIDEV.cpp:27:
drivers/Linux/SPIDEV.cpp: In static member function 'static uint8_t SPIDEVClass::transfer(uint8_t)':
drivers/Linux/SPIDEV.cpp:153:18: error: '_IOC_SIZEBITS' was not declared in this scope
  ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr);
                  ^
drivers/Linux/SPIDEV.cpp: In static member function 'static void SPIDEVClass::transfernb(char*, char*, uint32_t)':
drivers/Linux/SPIDEV.cpp:175:18: error: '_IOC_SIZEBITS' was not declared in this scope
  ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr);
                  ^
make: *** [Makefile:99: build/drivers/Linux/SPIDEV.o] Error 1

I'm surely missing a package... but can't state one. Any help?

@macvictor thanks for your post, it will help me a lot, I'm trying the same way.

mfalkvidd

@ghiglie https://lists.yoctoproject.org/pipermail/yocto/2016-January/028233.html seems to suggest that adding

#include <asm/ioctl.h>

would solve the problem. Could you try that?

sineverba

Was my fault!
**When copy and past command from word, for example, pay attention that software doesn't substitute the single "-" with a "-" longer.

I have a word with all commands, to replicate installation very fast. Was my fault (errr... Word fault.... but you understand). Have a nice day!

~~Hi,~~
~~I cannot go over the initialization of command.~~

RPI3 + Amplified antenna by GertSander (https://www.openhardware.io/view/17/Raspberry-Pi2-GPIO-interface-for-NRF24L01). Power from 5v/3A and power for antenna taken from both 5V via the 3.3v stepper down.

~~RPI3 is new, has about 12h (got yesterday).~~

Yesterday it did work at first attempt. Today I would replicate so I did delete the uSD and restart over. No way to get the gateway on work.

~~I did try 3 amplified antenna + 2 normal. No way.~~

~~I did enable from raspi-config the SPI (and only it).~~

~~It hangs on second line of output.~~

~~These are the logs:~~

sineverba@raspberrypi:~/MySensors $ ./configure --my-transport=nrf24 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020
[SECTION] Detecting target machine.
  [OK] machine detected: SoC=BCM2837, Type=rpi3, CPU=armv7l.
[SECTION] Detecting SPI driver.
  [OK] SPI driver detected:BCM.
[SECTION] Detecting init system.
  [OK] init system detected: systemd.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.
sineverba@raspberrypi:~/MySensors $ make
gcc -MT build/drivers/Linux/log.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/log.c -o build/drivers/Linux/log.o
g++ -MT build/drivers/Linux/IPAddress.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/IPAddress.cpp -o build/drivers/Linux/IPAddress.o
g++ -MT build/drivers/Linux/noniso.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/noniso.cpp -o build/drivers/Linux/noniso.o
g++ -MT build/drivers/Linux/GPIO.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/GPIO.cpp -o build/drivers/Linux/GPIO.o
g++ -MT build/drivers/Linux/SPIDEV.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/SPIDEV.cpp -o build/drivers/Linux/SPIDEV.o
g++ -MT build/drivers/Linux/Print.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/Print.cpp -o build/drivers/Linux/Print.o
g++ -MT build/drivers/Linux/EthernetClient.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/EthernetClient.cpp -o build/drivers/Linux/EthernetClient.o
g++ -MT build/drivers/Linux/compatibility.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/compatibility.cpp -o build/drivers/Linux/compatibility.o
g++ -MT build/drivers/Linux/SerialPort.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/SerialPort.cpp -o build/drivers/Linux/SerialPort.o
g++ -MT build/drivers/Linux/Stream.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/Stream.cpp -o build/drivers/Linux/Stream.o
g++ -MT build/drivers/Linux/interrupt.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/interrupt.cpp -o build/drivers/Linux/interrupt.o
g++ -MT build/drivers/Linux/SerialSimulator.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/SerialSimulator.cpp -o build/drivers/Linux/SerialSimulator.o
g++ -MT build/drivers/Linux/SoftEeprom.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/SoftEeprom.cpp -o build/drivers/Linux/SoftEeprom.o
g++ -MT build/drivers/Linux/EthernetServer.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/Linux/EthernetServer.cpp -o build/drivers/Linux/EthernetServer.o
g++ -MT build/examples_linux/mysgw.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c examples_linux/mysgw.cpp -o build/examples_linux/mysgw.o
gcc -MT build/drivers/BCM/bcm2835.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/BCM/bcm2835.c -o build/drivers/BCM/bcm2835.o
g++ -MT build/drivers/BCM/BCM.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/BCM/BCM.cpp -o build/drivers/BCM/BCM.o
g++ -MT build/drivers/BCM/SPIBCM.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/BCM/SPIBCM.cpp -o build/drivers/BCM/SPIBCM.o
g++ -MT build/drivers/BCM/Wire.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/BCM/Wire.cpp -o build/drivers/BCM/Wire.o
g++ -MT build/drivers/BCM/RPi.o -MMD -MP -march=armv8-a+crc -mtune=cortex-a53 -mfpu=neon-fp-armv8 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_SERIAL -DMY_DEBUG -DLINUX_SPI_BCM -DLINUX_ARCH_RASPBERRYPI -DMY_LINUX_SERIAL_PTY=\"/dev/ttyUSB020\" -DMY_LINUX_IS_SERIAL_PTY  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/BCM -c drivers/BCM/RPi.cpp -o build/drivers/BCM/RPi.o
g++ -pthread  -o bin/mysgw build/drivers/Linux/log.o build/drivers/Linux/IPAddress.o build/drivers/Linux/noniso.o build/drivers/Linux/GPIO.o build/drivers/Linux/SPIDEV.o build/drivers/Linux/Print.o build/drivers/Linux/EthernetClient.o build/drivers/Linux/compatibility.o build/drivers/Linux/SerialPort.o build/drivers/Linux/Stream.o build/drivers/Linux/interrupt.o build/drivers/Linux/SerialSimulator.o build/drivers/Linux/SoftEeprom.o build/drivers/Linux/EthernetServer.o build/examples_linux/mysgw.o build/drivers/BCM/bcm2835.o build/drivers/BCM/BCM.o build/drivers/BCM/SPIBCM.o build/drivers/BCM/Wire.o build/drivers/BCM/RPi.o
sineverba@raspberrypi:~/MySensors $ sudo ./bin/mysgw –d
[sudo] password for sineverba:
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-rc.2

sineverba

Hi to all,
I'm testing an ethernet gateway on RPI3, with nrf24 + 1 node with a relay.

I want introduce security and signing. On Arduino gateway / node no problem at all, but, how to do on the RPI3 as gateway?

I would get / create / set a software serial on PI itself and whitelisting it on the node, after I will introduce the AES Key and signing.

Cannot find in documentation how do it on PI3. Thank you very much!

ghiglie

@sineverba said in Building a Raspberry Pi Gateway:

Hi to all,
I'm testing an ethernet gateway on RPI3, with nrf24 + 1 node with a relay.

I want introduce security and signing. On Arduino gateway / node no problem at all, but, how to do on the RPI3 as gateway?

I would get / create / set a software serial on PI itself and whitelisting it on the node, after I will introduce the AES Key and signing.

Cannot find in documentation how do it on PI3. Thank you very much!

Earlier in this forum... https://forum.mysensors.org/topic/4803/building-a-raspberry-pi-gateway/350

ghiglie

@mfalkvidd I'm trying today, but to compile correctly the Docker image I'll have to clone to my github account or at least locally. My Dockerfile for the "Alpine edition" for Hass.io is simply:

ARG BUILD_FROM
ARG BUILD_ARCH
ARG BUILD_DATE
ARG BUILD_REF
ARG BUILD_VERSION

FROM ${BUILD_FROM}

ENV CONFIG_PATH=/data/options.json
ENV APPDIR=/opt/MySensors

RUN apt-get update && apt-get install -y --force-yes \
    make \
	 g++ \
	 git \
	 && rm -rf /var/lib/apt/lists/* /tmp/* /var/tmp/* ~/.cache \
	 && git clone https://github.com/mysensors/MySensors.git --branch development $APPDIR


# Copy root filesystem
COPY rootfs /

#CMD [ "/run.sh" ]

I deleted the LABELS 'cause... the data is still too rawly "buried" from others.

The Configure and Make is in run.sh.

BTW, I still need to figure out how to start mysgw as service... Mainlyt I'd like to redirect the log: how can I do this safely?

And... can I use the rx/tx/err led feature on Raspi too (aside being in a Docker) ?

EDIT: the code add works!
Another question: I'm not getting far from this... what is it trying to do?

: Starting gateway...
: Protocol version - 2.2.0-rc.2
: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0-rc.2
: TSF:LRT:OK
: TSM:INIT
: TSF:WUR:MS=0

sineverba

@ghiglie Thank you, I did see that was for 2.1.1. Just playing with them!

alowhum

Does the Pi Gateway support the MY_SIGNING_SIMPLE_PASSWD option? I couldn't find anything about that. I've been gearing up to use that feature in my network, but I've also been playing with moving my gateway onto my Pi Zero W.

gohan

@alowhum If you want to just encrypt data, just add the encryption key in the myconfig.h file and compile it

💬 Building a Raspberry Pi Gateway

Suggested Topics

Missing Notification Settings
Bug Reports • • edoardoo

💬 Water Meter Pulse Sensor
Announcements • • hek

💬 Building a WiFi Gateway using ESP8266
Announcements • • hek

Sensebender Micro
Announcements • • hek

💬 Components
Announcements • • hek

💬 Battery Powered Sensors
Announcements • battery • • hek

9
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

💬 Building a Raspberry Pi Gateway

Suggested Topics

Missing Notification Settings Bug Reports • • edoardoo

💬 Water Meter Pulse Sensor Announcements • • hek

💬 Building a WiFi Gateway using ESP8266 Announcements • • hek

Sensebender Micro Announcements • • hek

💬 Components Announcements • • hek

💬 Battery Powered Sensors Announcements • battery • • hek

9Online

11.4kUsers

11.1kTopics

112.7kPosts

Missing Notification Settings
Bug Reports • • edoardoo

💬 Water Meter Pulse Sensor
Announcements • • hek

💬 Building a WiFi Gateway using ESP8266
Announcements • • hek

Sensebender Micro
Announcements • • hek

💬 Components
Announcements • • hek

💬 Battery Powered Sensors
Announcements • battery • • hek

9
Online

11.4k
Users

11.1k
Topics

112.7k
Posts