Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 RFM69 Sensors / Gateway

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/535/RFM69-Sensors-Gateway
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by

Looks as though you have several different boards. You should probably make separate postings for each one of them.
Reply Quote 0
1 Reply Last reply
Александр Бондаренко last edited by @openhardware.io

@openhardware-io hi i want to test your board with rs485. please give me the source files of the project. thank.
Reply Quote 0
1 Reply Last reply

3
Posts

751
Views

Log in to reply

Suggested Topics

💬 Syma S107 Bluetooth mod (connect any toy with your phone!)
OpenHardware.io • nrf52832 nrf52 remote control hack bluetooth low energy toys • • openhardware.io

1

0
Votes

1
Posts

9
Views

No one has replied
💬 MySensors InCan double light switch
OpenHardware.io • mysensors nrf24l01 relay switch light hlk-pm01 acdc in-wall • • openhardware.io

24

1
Votes

24
Posts

2445
Views

The author has done some good work ensuring good design practices; trace separation, fuses, etc. but I don't see any extra I/O brought out on this particularl switch. You would have to carefully solder to the chip itself, and modify the code a bit. You could use magnetic switches. Put a magnet on the blinds and the switch in window sill. The author notes that this is not an Arduino, but uses the same chip that the Arduino uses. The author doesn't explain how the chip is programmed. This method could have been used. It may be just as easy to use an RF Nano with a little power supply. This suggestion is not nearly as robust as the author's. For example, these power supplies have gotten bad reviews mainly because the mains power traces are too close together. I justify using them because in all likelihood a failure will pop the power supply and probably the Nano, too, noting that these are cheaper than the fuses you would put in to protect them. I am fully aware of the risks involved in doing this, and you should be, too (eg. burning down your house). -OSD
💬 VR-Shield
OpenHardware.io • bluetooth shield sensors virtual reality imus • • openhardware.io

1

0
Votes

1
Posts

11
Views

No one has replied
💬 AC-DC double solid state relay module
OpenHardware.io • light hlk-pm01 acdc light switch solid state relay • • openhardware.io

226

7
Votes

226
Posts

103501
Views

What I didn't quite figure out was how it operates independently as a regular light switch. What I find most interesting is that this is 8 years old. There have been some incredible advances in the IoT world in that time. I was about to do a similar thing which morphed into an ESP-12F then added a touch screen. I call it the Universal Light Switch Imagine this: All the switches are identical. Any switch can easily be configured to control up to five devices ... and then changed, on-the-fly, to control a different set of devices. My design is part of a system that would require a controller (eg. Home Assistant), an MQTT broker, and receiving modules in the devices being switched. It's WiFI which assumes an access point. The DIY ULS is under $20 and the off-the-shelf receiving modules are under $10. (About the cost of a non-networked dimmer switch) If one doesn't have the controller and MQTT broker, they can run on an old (5 years?) computer (which is cheaper than an old RasberryPi). This project is a good one! OSD
💬 MyGateway
OpenHardware.io • mysensors gateway rfm69 ethernet poe • • openhardware.io

10

0
Votes

10
Posts

152
Views

Oh, I never even thought of that as a possibility. I really like KiCad, and it's my preference. For a while I had Eagle for work, but even then I still preferred KiCad whenever I was given a choice.

28
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1