Not all Relais visible in Domoticz



  • I started a project with 5 relays and 2 binary buttons. In Domotics 3 of the 5 relays pops up including the 2 binary buttons. Why not 5 relays?

    
    // Enable debug prints to serial monitor
    #define MY_DEBUG
    
    // Enable and select radio type attached
    #define MY_RADIO_NRF24
    //#define MY_RADIO_RFM69
    
    // Enable repeater functionality for this node
    #define MY_REPEATER_FEATURE
    
    #include <SPI.h>
    #include <MySensors.h>
    #include <Bounce2.h>
    
    #define RELAY_1  A0  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
    #define NUMBER_OF_RELAYS 5 // Total number of attached relays
    #define RELAY_ON 0  // GPIO value to write to turn on attached relay
    #define RELAY_OFF 1 // GPIO value to write to turn off attached relay
    
    #define CHILD_ID_IRBIN 3
    #define CHILD_ID_IRBUI 4
    #define IRBIN_PIN  3  // Arduino Digital I/O pin for button/reed switch
    #define IRBUI_PIN  4
    
    Bounce debouncerIRBIN = Bounce();
    Bounce debouncerIRBUI = Bounce();
    
    int oldValue_IRBIN = -1;
    int oldValue_IRBUI = -1;
    
    MyMessage msgIRBIN(CHILD_ID_IRBIN, V_TRIPPED);
    MyMessage msgIRBUI(CHILD_ID_IRBUI, V_TRIPPED);
    
    void before()
    {
    	for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
    		// Then set relay pins in output mode
    		pinMode(pin, OUTPUT);
    		// Set relay to last known state (using eeprom storage)
    		digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
    	}
    }
    
    void setup()
    {
      // Setup the button1
      pinMode(IRBIN_PIN, INPUT);
      debouncerIRBIN.attach(IRBIN_PIN);
      debouncerIRBIN.interval(5);
      digitalWrite(IRBIN_PIN, HIGH);
      // Setup the button2
      pinMode(IRBUI_PIN, INPUT);
      debouncerIRBUI.attach(IRBUI_PIN);
      debouncerIRBUI.interval(5);
      digitalWrite(IRBUI_PIN, HIGH);
    
      }
    
    void presentation()
    {
     // Register binary input sensor to gw (they will be created as child devices)
      // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage.
      // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
      present(CHILD_ID_IRBIN, S_DOOR);
      present(CHILD_ID_IRBUI, S_DOOR);
    
    	for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
    		// Register all sensors to gw (they will be created as child devices)
    		present(sensor, S_BINARY);
    	}
     }
    
    
    void loop()
    {
      debouncerIRBIN.update();
      // Get the update value
      int valueIRBIN = debouncerIRBIN.read();
    
      if (valueIRBIN != oldValue_IRBIN) {
        // Send in the new value
        send(msgIRBIN.set(valueIRBIN == HIGH ? 1 : 0));
        oldValue_IRBIN = valueIRBIN;
      }
    
      debouncerIRBUI.update();
      // Get the update value
      int valueIRBUI = debouncerIRBUI.read();
    
      if (valueIRBUI != oldValue_IRBUI) {
        // Send in the new value
        send(msgIRBUI.set(valueIRBUI == HIGH ? 1 : 0));
        oldValue_IRBUI = valueIRBUI;
      }
    }
    
    void receive(const MyMessage &message)
    {
    	// We only expect one type of message from controller. But we better check anyway.
    	if (message.type==V_STATUS) {
    		// Change relay state
    		digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
    		// Store state in eeprom
    		saveState(message.sensor, message.getBool());
    		// Write some debug info
    		Serial.print("Incoming change for sensor:");
    		Serial.print(message.sensor);
    		Serial.print(", New status: ");
    		Serial.println(message.getBool());
    	}
    }
    


  • For me, sometimes Domoticz does not show a switch until it gets a value, even though the switch was presented. I add a small routine to Loop() with a flag so it only runs the first time after startup. Then i send the default value for each switch, Usually Off. It is not very elegant, but seems to work.
    If (startup) {
    Send initial value for each switch/relay
    startup=false;
    }



  • @nagelc
    Thanks for the reply but I am not that experience. I must add your script to the "LOOP" but doing that I get a message "startup" was not declared in the scope. Can you show me was to declair?


  • Mod

    @dick add

    static bool startup = true;
    

    before the If (startup) line.

    You might also need to add delay(100) after each present and send, to avoid stressing the radio and power source too much.



  • @mfalkvidd Exactly. Thanks for clarifying.



  • @mfalkvidd I tested the solution and the LOOP code looks like this
    but having an error during compiling ("IF" was not declared in this scope). how can I fix that?

    void loop()
    {
      debouncerIRBIN.update();
      // Get the update value
      int valueIRBIN = debouncerIRBIN.read();
    
      if (valueIRBIN != oldValue_IRBIN) {
        // Send in the new value
        send(msgIRBIN.set(valueIRBIN == HIGH ? 1 : 0));
        oldValue_IRBIN = valueIRBIN;
      }
    
      debouncerIRBUI.update();
      // Get the update value
      int valueIRBUI = debouncerIRBUI.read();
    
      if (valueIRBUI != oldValue_IRBUI) {
        // Send in the new value
        send(msgIRBUI.set(valueIRBUI == HIGH ? 1 : 0));
        oldValue_IRBUI = valueIRBUI;
      }
      
      static bool startup = true;
      If (startup) {
    Send initial value for each switch/relay
    startup=false;
    }
    }```

  • Mod

    @dick if needs to be lowercase. Change "If" to "if".



  • @mfalkvidd thanks for your support and no errors anymore. Unfortunately it did not work forme. probably I split my sensors in to, one with the relais switches and 1 with the binary buttons. I think that is the only way to continue right now.



  • Another thing to try. Try changing the button IDs to 6 and 7.

    You define the button child IDs as 3 and 4.
    The relays are presented with child ID's 1 through 5 by the loop in Presentation(). So the buttons have the same child IDs as two of the relays. Some sensors can have the same child ID, like temperature and humidity, but I don't know about S_DOOR and S_BINARY.

    Also, delete this code i suggested. It needs some tweaking and I suspect the issue is really the overlap of the child IDs:
    static bool startup = true;
    If (startup) {
    Send initial value for each switch/relay
    startup=false;
    }


Log in to reply
 

Suggested Topics

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts