Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Motorola Focus Tag 4522A

artag last edited by artag

I picked up some Motorola Focus Tags. These are part of their Hubble security camera system - I think they're used to identify things that move in the camera's view.

They're 42mm discs with a CR2032 , button, a led, a piezo disc and, I think, a light sensor and an accelerometer. Processor is an nrf51822 CEAAE0.

There are two other chips I can't identify. One has only the letters NAI (the N is stylised, could be a logo) and a QR code that's too small to read. It's quite thick - it's probably an accelerometer / gyro. 16 pins, I think

The other is marked 2411 2276.1 UFC511. It has 20 pins and seems to be linked to what I initially took to be a light sensor but could be a chip antenna. In fact, given the PCB layout in the area (restricted ground plane) and the lack of any other antenna, it's probably a PA.
Reply Quote 0
1 Reply Last reply

1
Posts

536
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50410
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

5

0
Votes

5
Posts

27
Views

@Tmaster Never assume the original PCB was just a circuit of components, the PCB can incorporate RF shields and antenna radio ground planes...
Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

5

1
Votes

5
Posts

70
Views

It probably has to do with fewer people buying them once summer ends, so companies might lower prices to clear out stock before winter.
New user has questions
Hardware • • Doggie

7

0
Votes

7
Posts

50
Views

I am new in this forum and I have a question regarding mysensors and iobroker. I did not work with mysensors up to now. Since some weeks I use iobroker installed on a raspberrypi. Now I want to integrate my 433 Mhz doorbell in iobroker. I know, that there is an adapter for mysensors in iobroker. My question is: Is it possible to get a notification in iobroker if someone is pressing the button on my doorbell? As I understood, I have to connect the receiver to an arduino nano and connect the arduino to my rasberrypi on which iobroker is running.
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

2

0
Votes

2
Posts

21
Views

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }
Arduino Nano Every problem
Hardware • • hakha4

6

1
Votes

6
Posts

84
Views

I bought the Every because it implied it was backward compatible with the nano. No, it's not, as we found out. Be that as it may, any word on a getting the Every working with mySensors?

Motorola Focus Tag 4522A

Suggested Topics

Over the air updates
General Discussion • • ToSa

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

New user has questions
Hardware • • Doggie

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Arduino Nano Every problem
Hardware • • hakha4

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Motorola Focus Tag 4522A

Suggested Topics

Over the air updates General Discussion • • ToSa

hlk-pm01 are to noisy for rfm69? Hardware • • Tmaster

Best time of year to buy higher quality small project solar panels? Hardware • • NeverDie

New user has questions Hardware • • Doggie

Does MySensors require Arduino Timer 2? Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Arduino Nano Every problem Hardware • • hakha4

0Online

11.4kUsers

11.1kTopics

112.7kPosts

Over the air updates
General Discussion • • ToSa

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

New user has questions
Hardware • • Doggie

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Arduino Nano Every problem
Hardware • • hakha4

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts