💬 Security & Signing

[sineverba]

@pepson And, last all, you can use the mysensors debug options. Try. Try. Try! This is the best option offered to you to learn. Try!
At max, nothing works ;)

[pepson]

@sineverba
ok all is very good.

But what give me this if i can connect nodes also with defines bla bla bla in skethc and also without define bla bla bla in sketch?
But Do I think right ? In each of these accidents in the eeprom I need to have the keys loaded?

[sineverba]

@pepson only one word. Try. Really, you are lost in 1 cm of water. Try. And if it doesn't work, open your topic, showing exactly your sketches and what have you done.

[pepson]

ok thanks

[pepson]

Ok i build my gateway on RPI on MySensors 2.2.0 with this configuration:

./configure --my-transport=rfm69 --my-rfm69-frequency=868 --my-is-rfm69hw --my-gateway=ethernet --my-port=5003 --my-signing=software --my-signing-request-signatures

Then generate 3 key and setup it on gateway.

Then clear_epprom on Arduino MIni Pro, and then send sketch security with add serial, HMAC, and AES. Then put sketch with add this on top sketch with my SERIAL generated on gateway RPI.

#define MY_SIGNING_SOFT
#define MY_SIGNING_SOFT_RANDOMSEED_PIN 7
#define MY_SIGNING_REQUEST_SIGNATURES
#define MY_SIGNING_NODE_WHITELISTING {{.nodeId = GATEWAY_ADDRESS,.serial = {0X2C,0X61,0X17,0X2E,0XEE,0XDD,0XCC,0XBB,0XAA}}} // got from gateway setup

After that i run HA and he not found my nodes...
WHat is wrondg ?

[Anticimex]

@pepson well for starters, don't start out with whitelisting unless you know exactly what you are doing. First you have to verify that your network is stable enough to handle the security protocol. The simplest option is to only enable encryption, or use the simple password flag options. Once you have established that your gw and nodes are capable of communicating securely you can move on to personalization and whitelisting.

[pepson]

@anticimex
What you mean white list?

Before adding all security my nodes and gateway works perfect.

[Anticimex]

@pepson you define whitelisting so I presume you use it. But I don't see your gw flags specifying it so of course it does not work. So get rid of that flag from your config unless you know what it mean so that you set it up properly.

[pepson]

@anticimex

What flag i must remove ?
This :
#define MY_SIGNING_NODE_WHITELISTING {{.nodeId = GATEWAY_ADDRESS,.serial = {0X2C,0X61,0X17,0X2E,0XEE,0XDD,0XCC,0XBB,0XAA}}} // got from gateway setup

But on GW i setup this:
sudo mysgw --set-soft-serial-key=2C61172EEEDDCCBBAA && sudo mysgw --set-aes-key=9D2AD43CF909875C4C77111111111111 && sudo mysgw --set-soft-hmac-key=A2A64C48EA6765C5DAEFA12A1E41E2F038515A9CAED9FED73D11111111111111

[Anticimex]

@pepson please just read the documentation. And more importantly, follow it.
Isn't it obvious that it is the flag that mention whitelisting that is supposed to be removed unless you intend to use whitelisting, in which case you ought to know how to set it up properly at both ends?

[pepson]

@anticimex

Sorry i dont undestand

[Anticimex]

@pepson https://www.mysensors.org/apidocs/group__MySigninggrpPub.html

Note that it is the documentation for the latest release (simple password flags work differently compared to previous releases, see release notes for the latest release).

[pepson]

HI
i don as describe...

1. install gateway on raspberry with this configuration:
   ./configure --my-transport=rfm69 --my-rfm69-frequency=868 --my-is-rfm69hw --my-gateway=ethernet --my-port=5003 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18 --my-signing=software --my-signing-request-signatures --my-signing-weak_security --my-signing-debug

and then generate serial, aes and hmac

pi@raspberrypi:~/MySensors $ sudo mysgw --gen-soft-serial-key
SOFT_SERIAL | 8FC828503E6EB14C5D

The next line is intended to be used in SecurityPersonalizer.ino:
#define MY_SOFT_SERIAL 0X8F,0XC8,0X28,0X50,0X3E,0X6E,0XB1,0X4C,0X5D

To use this key, run mysgw with:
--set-soft-serial-key=8FC828503E6EB14C5D
pi@raspberrypi:~/MySensors $ sudo mysgw --gen-soft-hmac-key
SOFT_HMAC_KEY | 0D682ED05106E5F361C64288D68AAE1B34F5FFB62B4E39773C9D92DED04B6514

The next line is intended to be used in SecurityPersonalizer.ino:
#define MY_SOFT_HMAC_KEY 0XD,0X68,0X2E,0XD0,0X51,0X6,0XE5,0XF3,0X61,0XC6,0X42,0X88,0XD6,0X8A,0XAE,0X1B,0X34,0XF5,0XFF,0XB6,0X2B,0X4E,0X39,0X77,0X3C,0X9D,0X92,0XDE,0XD0,0X4B,0X65,0X14

To use this key, run mysgw with:
--set-soft-hmac-key=0D682ED05106E5F361C64288D68AAE1B34F5FFB62B4E39773C9D92DED04B6514
pi@raspberrypi:~/MySensors $ sudo mysgw --gen-aes-key
AES_KEY | 8FDB1EE8D0351CFF874D337731BF37AE

The next line is intended to be used in SecurityPersonalizer.ino:
#define MY_AES_KEY 0X8F,0XDB,0X1E,0XE8,0XD0,0X35,0X1C,0XFF,0X87,0X4D,0X33,0X77,0X31,0XBF,0X37,0XAE

To use this key, run mysgw with:
--set-aes-key=8FDB1EE8D0351CFF874D337731BF37AE
pi@raspberrypi:~/MySensors $

and setup it on my gateway

sudo mysgw --set-soft-serial-key=8FC828503E6EB14C5D && sudo mysgw --set-aes-key=8FDB1EE8D0351CFF874D337731BF37AE && sudo mysgw --set-soft-hmac-key=0D682ED05106E5F361C64288D68AAE1B34F5FFB62B4E39773C9D92DED04B6514

all is ok to this moment

Then

2. clear eeprom in node Arduino pro mini with this sketch:
   https://github.com/sineverba/domoraspi/tree/master/utils/sketches
3. write sketch security with setup my serial, aes and hmac

https://github.com/sineverba/domoraspi/tree/master/utils/sketches

at the top setup...
/************************************ User defined key data ***************************************/

/** @brief The user-defined HMAC key to use unless @ref GENERATE_HMAC_KEY is set */
//#define MY_HMAC_KEY 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
#define MY_HMAC_KEY 0XD,0X68,0X2E,0XD0,0X51,0X6,0XE5,0XF3,0X61,0XC6,0X42,0X88,0XD6,0X8A,0XAE,0X1B,0X34,0XF5,0XFF,0XB6,0X2B,0X4E,0X39,0X77,0X3C,0X9D,0X92,0XDE,0XD0,0X4B,0X65,0X14

/** @brief The user-defined AES key to store in EEPROM unless @ref GENERATE_AES_KEY is set */
//#define MY_AES_KEY 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
#define MY_AES_KEY 0X8F,0XDB,0X1E,0XE8,0XD0,0X35,0X1C,0XFF,0X87,0X4D,0X33,0X77,0X31,0XBF,0X37,0XAE

/** @brief The user-defined soft serial to use for soft signing unless @ref GENERATE_SOFT_SERIAL is set */
#define MY_SOFT_SERIAL 0X8F,0XC8,0X28,0X50,0X3E,0X6E,0XB1,0X4C,0X5D

/***************************** Flags for guided personalization flow ******************************/

4. then write my sketch relay with added at the top this info:

#define MY_SIGNING_SOFT
#define MY_SIGNING_SOFT_RANDOMSEED_PIN 7
#define MY_SIGNING_REQUEST_SIGNATURES
#define MY_SIGNING_NODE_WHITELISTING {{.nodeId = GATEWAY_ADDRESS,.serial = {0X8F,0XC8,0X28,0X50,0X3E,0X6E,0XB1,0X4C,0X5D}}} // got from gateway setup

and now on my Home assistant in file
/home/homeassistant/.homeassistant/mysensors.json

found my node but wthout full information like name....
{
"0": {
"battery_level": 0,
"sketch_name": null,
"sketch_version": null,
"children": {},
"type": 18,
"protocol_version": "2.2.0",
"sensor_id": 0
},
"33": {
"battery_level": 0,
"sketch_name": null,
"sketch_version": "1.0",
"children": {
"1": {
"type": 3,
"id": 1,
"values": {
"2": "1"
},
"description": ""
}
},
"type": 17,
"protocol_version": "2.2.0",
"sensor_id": 33
}
}

and in Home Assistant is not show in devices this node. Not found it.
What i done wrong ?

[Anticimex]

@pepson said in 💬 Security & Signing:

MY_SIGNING_NODE_WHITELISTING

How many times do I need to tell you to get rid of the whitelisting flag?

[pepson]

@anticimex
Ok read... but...
when i use MY_SIGNING_NODE_WHITELISTING i must on node in sketch add serial number my gateway and also serial number for node. But from where i can get serial number for my arduino pro mini ? I dont know...becasue i don use ATSHA204 but i use only soft signing....

[sineverba]

@pepson This is the serial OF GATEWAY. Not your Arduino. You need to put serial of GATEWAY.

Please, first of all, DONT' USE WHITELISTING. And pay attention: if you enabled it, remove it and:

1 - clear eeprom
2 - flash eeprom with keyes
3 - reload sketch (without whitelisting)

[sineverba]

@pepson Don't need all copy and paste, enough link :).

Btw, before move to Home Assistant, where is the output of debug of MySensors?

sudo mysgw -d

Of course, you need before stop service.

Resetting the node, what you get in debug?

When ALL ok, move to HomeAssistant.

And remember, after check that debug is ok...

sudo make install && sudo systemctl enable mysgw.service && sudo systemctl start mysgw.service

[pepson]

In my first time I use only serial number gateway in flag whitelistening and also not working.

[sineverba]

@pepson Last time. Please.
REMOVE
WHITELISTING
FROM
YOUR
SKETCH

Clear EEPROM and paste here output of debug. No other.

[pepson]

@sineverba
OK wait for info