Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 MDMSPanel "Nextion"

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/676/MDMSPanel-Nextion
Reply Quote 1
1 Reply Last reply
sebdetours last edited by

Hello Kalina.

Really good job. I like the way you designed your products. (not only this one

A question about the Box. Did you take a standart case that you cut out, or did you have your own case made from a manufacturer?

Regards
Reply Quote 0
1 Reply Last reply
kalina Hardware Contributor last edited by @sebdetours

@sebdetours said in MDMSPanel "Nextion":

Did you take a standart case that you cut out?

Hi @sebdetours, yes. This is G1910 (Gainta) box. See drawing attached to projet files.
Reply Quote 0
1 Reply Last reply

arduino 119 rtc 5 atmega 3 modbus 3 display 3 nextion 3 st485 2 jtag 2 megacore 1

3
Posts

749
Views

Log in to reply

Suggested Topics

💬 Temperature-Humidity-Pressure Sensor
OpenHardware.io • arduino temperature esp8266 sensor humidity raspberry pi esp32 pressure • • openhardware.io

6

0
Votes

6
Posts

1185
Views

Advantage of this sensor is fast and easy installing by the non qualified personal. The sensor is designed for large agriculture facility with many greenhouses where is needed to be controlled temperature and humidity, the atmospheric pressure is for control the motor of air inlet and outlet. With help of the sensor installed outside the greenhouse provide information about positive/negative pressure inside the greenhouse. Finlay the software read accurate temp/humid value of the Si7021, and only atmospheric pressure of BMP180, the temperature sensor inside the BMP180 is used only by the sensor itself to provide accurate atmospheric pressure measurements. The sensor can be used also for home automation, and drone applications where is needed correction of the UAV barometric sensor compared to the ground barometric sensor, also humidity measurement can help the pilot to calculate more accurate flying time.
💬 ESPboy: Games, IoT, STEM for education & fun (ESP8266 core)
OpenHardware.io • arduino esp8266 iot diy console gadget retro game • • openhardware.io

6

0
Votes

6
Posts

71
Views

I think these look very interesting to do with small children may be able to stimulate their curiosity, the current video games are too much influence on children, occasionally the family together to do their own small games is a new experience.
💬 Hover SmartHome sensor and controller system
OpenHardware.io • arduino nrf24l01 esp8266 raspberry stepper motor smarthome cortana wiolink • • openhardware.io

1

0
Votes

1
Posts

1109
Views

No one has replied
Parallel Gateways
General Discussion • arduino gateway raspberry pi • • jocke4u

10

0
Votes

10
Posts

55
Views

@jocke4u I run 2 RF gateways and it's not a problem. When you 'migrate' a node to a new gateway make sure to run the mysensors clear eeprom sketch first to get rid of the old routing table or you might have issues.
How to make sense of Struct data received from Arduino in RPi via NRF24?
General Discussion • arduino raspberry pi rf24 • • nrf24_is_hard

2

0
Votes

2
Posts

14
Views

@nrf24_is_hard When I sent data between an Aduino and the RPi I discovered that I have to make the the receiving and the sending structs the same size AND the variables be on 4 byte boundaries. Change your char name[15] to char name[16] Another challenge is that the number of bytes of type int are different. If I remember correctly, Arduino Uno is 2 bytes and RPi is 4 bytes. To make matters worse, some compilers make the least significant byte the first byte of a word and others make it the last byte of a word. eg, sending the value 1 would be received as 16777216 (0x00000001 vs 0x01000000) There are a lot more gotcha's OSD
💬 MDMSNode "Lighting"
OpenHardware.io • mysensors arduino nrf24l01 rfm69 light acdc light switch • • openhardware.io

37

2
Votes

37
Posts

10438
Views

Hi @aramko-aramko. Unfortunately, this model is already sold. You can look at the upgraded version of this device - MDMSNode "Lighting" Rev 1.1.
MySensors MQTT gateway and serial rs485 sensor node communication
Development • arduino gateway mqtt serial rs485 openhab2 nodes • • ehome

3

0
Votes

3
Posts

3897
Views

Thanks for your fast reply. That sounds easy. And you think that the communication between sensor nodes and Gateway are still possible via wired RS485? I tried to find an example on this site for sending Information from Gateway to sensor nodes. (via SendMessage ?) For example I like to Switch on/off an light that is connected to an relay board at my sensor node. Communcation Flow: OpenHab2 --> MQTT --> Gateway --> RS485 --> Sensor Node --> Relay Board Currently I have an working RS485 Connection between my Arduino Uno's with the use from SoftwareSerial library. During my testings I realized, that the message that I triy to send "Hello" will be sent to the other arduino char by char. Is that true? Because I tried to raise up an pin on HIGH with "if(msg == "Hello")..." But it doesn't worked. Will the sendMsg method from the MySensor library handle this out of the box? Regards, Simon
How to check if serial gateway is operational ?
Development • arduino serial gateway • • joshmosh

4

0
Votes

4
Posts

2214
Views

@fot said: Hi! I ask my gateway about it's version (0;0;3;0;2;). It will responde with the library version number (1.4.1 in my case). It tells me that the gateway software is up and running. But it will not give me any clue about if the (NRF)network is working. That's a problem, right. I only ask the gateway if no other packages are received in $timeout seconds. /Magnus Of course ! Thank you for pushing my nose on it. Sometimes you don't see the most obvious Since my gateway is relatively close to the controller (Domoticz on a Raspi), I can do a hard reset of the gateway (via Raspi GPIO), which should resolve the issue. Cheers Josh

20
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1