Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

New Sense Bender GW no USB response

KenKrick last edited by

I'm new to this so I bought a Sense Bender GW and several nodes.

Was following the driver installation, copied the driver, opened the device manger and plugged in the GW and there was no response to the device in the device manager. I tried a couple different USB cables as well as restarting my Win10 laptop. No matter what I do, I can't get the computer to respond to my brand new GW. Any hints??
Reply Quote 0
1 Reply Last reply

gw usb 1

1
Posts

560
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
A low cost energy meter
My Project • • OldSurferDude

7

1
Votes

7
Posts

44
Views

@OldSurferDude yes, you are correct. this sensor is capable of 50A continuous, which safely I would make it working at 40A max., but for such an important load as in your case I would go for a beefier one, like the ACS75x, 77x, but at this point I would also change the node's form factor for space and insulation reasons. On my application on the RV I have a max. curr. of 13A running on a AWG14-16 cable (European rules for RVs), so I did not ask myself too many questions beside, of course, safety. About the signal, it will be a sinusoidal signal swinging around Vcc/2. Vcc can be easily measured internally on the ATmega328. On all my DC sensors I measure Vcc at every loop, just before measuring the ADCs. Honestly, when the space is not an issue like in my RV, I would rather use a ring core current transformer, and I would get rid of noise, response time, power dissipation, but over all no need to cut any cable. Long story short, it has been a nice experiment and I used it for 6 months, and then I switched back to my RF-NANO based RS485-Modbus - Mysensors bridge connected to an off-the shelf power analyzer. Just for fun I attach a pic of my 12Vdc sensors installed on my RV. Forgive me for the spaghetti wiring on the right side, but this is an area that needs improvement.
Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

1

0
Votes

1
Posts

12
Views

No one has replied
Halloween Lights
My Project • led strip light ws2812b • • KevinT

1

3
Votes

1
Posts

24
Views

No one has replied
HVAC Controller
My Project • • Michael Link

3

1
Votes

3
Posts

28
Views

We are of like minds, Don't like the cloud based controls (that's another discussion). In my case I have a Bryant/Connex system, heat pump, variable speed fan and 4 zones. There's a lot going on: the 4 zones creates 16 profiles. The fan speed for a profile will depend on the indoor and outdoor temperature. The thermal fluid pump also has to be controlled. A profile will have an optimal air pressure, so there's a sensor there. The controller works just fine not being connected to the cloud. But I want to set the parameters remotely, Bryant/Connex can do this. I also wnat the status of the various actuators and sensors to show up in Home Assistant. The signals sent over the RS422 are proprietary. My plan was to reverse-engineer the signals. After doing this I'll have to experiment to get the right mix of air pressue, fan speed and thermal fluid flow for each profile. I'd like to do the same for my AO Smith heat pump water heater. I'd like to follow your progress. OSD
nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

44

18
Votes

44
Posts

8024
Views

The output of the display could also be sent over serial, but the whole idea is you can walk around with the doctor and improve your results as you go.

New Sense Bender GW no USB response

Suggested Topics

Welcome
Announcements • • hek

A low cost energy meter
My Project • • OldSurferDude

Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

Halloween Lights
My Project • led strip light ws2812b • • KevinT

HVAC Controller
My Project • • Michael Link

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

New Sense Bender GW no USB response

Suggested Topics

Welcome Announcements • • hek

A low cost energy meter My Project • • OldSurferDude

Water Meter or "How to get Home Assistant to send saved data to an Arduino" My Project • • OldSurferDude

Halloween Lights My Project • led strip light ws2812b • • KevinT

HVAC Controller My Project • • Michael Link

nRF24Doctor My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

0Online

11.4kUsers

11.1kTopics

112.7kPosts

Welcome
Announcements • • hek

A low cost energy meter
My Project • • OldSurferDude

Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

Halloween Lights
My Project • led strip light ws2812b • • KevinT

HVAC Controller
My Project • • Michael Link

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts