HA not seeing sensors.



  • I'm going crazy, any help appreciated.

    My setup.
    Pi 3 controller on ethernet.
    HASSOS recently installed.
    MQTT.
    NodeMCU 09 wifi gateway.
    My sensors switch / lamp.

    Nodes and gateway talking fine. Controller and gateway register with MQTT server on HA (mosquitto).

    Nodes are registering with gateway but not getting 'initial value' back from HA and repeats request.

    This happened after I updated HA. Any help appreciated.



  • @el-tigro do you send initial values after presentation? HA won't recognize your sensor if it doesn't send values. You can check what exactly it needs to be sent here: https://www.home-assistant.io/components/mysensors/. There are separate pages for each sensor type with sketch examples.



  • @monte
    Node debug. Appears to register but then no response to initial value request.
    0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
    3 TSM:INIT
    4 TSF:WUR:MS=0
    11 TSM:INIT:TSP OK
    12 TSM:INIT:STATID=66
    15 TSF:SID:OK,ID=66
    16 TSM:FPAR
    53 TSF:MSG:SEND,66-66-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    192 TSF:MSG:READ,0-0-66,s=255,c=3,t=8,pt=1,l=1,sg=0:0
    197 TSF:MSG:FPAR OK,ID=0,D=1
    2060 TSM:FPAR:OK
    2061 TSM:ID
    2062 TSM:ID:OK
    2064 TSM:UPL
    2069 TSF:MSG:SEND,66-66-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
    2082 TSF:MSG:READ,0-0-66,s=255,c=3,t=25,pt=1,l=1,sg=0:1
    2086 TSF:MSG:PONG RECV,HP=1
    2089 TSM:UPL:OK
    2092 TSM:READY:ID=66,PAR=0,DIS=1
    2096 TSF:MSG:SEND,66-66-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
    2103 TSF:MSG:READ,0-0-66,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
    2110 TSF:MSG:SEND,66-66-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.1.1
    2118 TSF:MSG:SEND,66-66-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
    4127 TSF:MSG:SEND,66-66-0-0,s=255,c=3,t=11,pt=0,l=9,sg=0,ft=0,st=OK:Grey Lamp
    4135 TSF:MSG:SEND,66-66-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
    4144 TSF:MSG:SEND,66-66-0-0,s=2,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
    4150 MCO:REG:REQ
    4153 TSF:MSG:SEND,66-66-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
    4176 TSF:MSG:READ,0-0-66,s=255,c=3,t=27,pt=1,l=1,sg=0:1
    4182 MCO:PIM:NODE REG=1
    4184 MCO:BGN:STP
    4185 MCO:BGN:INIT OK,TSP=1
    Sending initial value
    4190 TSF:MSG:SEND,66-66-0-0,s=2,c=1,t=2,pt=2,l=2,sg=0,ft=0,st=OK:0
    Requesting initial value from controller
    4198 TSF:MSG:SEND,66-66-0-0,s=2,c=2,t=2,pt=0,l=0,sg=0,ft=0,st=OK:
    Sending initial value
    6207 TSF:MSG:SEND,66-66-0-0,s=2,c=1,t=2,pt=2,l=2,sg=0,ft=0,st=OK:0
    Requesting initial value from controller



  • @el-tigro
    I have other nodes / devices and they all do the same.
    HA config

    mysensors:
    gateways:
    - device: '/dev/ttyUSB0'
    persistence_file: '/config/myhouse/mysensors.json'
    - device: mqtt
    persistence_file: '/config/myhouse/mysensors4.json'
    topic_in_prefix: 'mygateway1-out'
    topic_out_prefix: 'mygateway1-in'
    optimistic: false
    persistence: true
    retain: true
    version: '2.0'

    mqtt:
    broker: 192.168.1.***
    port: 1883
    client_id: home-assistant-1
    keepalive: 60

    Gateway code

    #define MY_DEBUG
    #define MY_BAUD_RATE 115200
    #define MY_RADIO_NRF24
    #define MY_GATEWAY_MQTT_CLIENT
    #define MY_GATEWAY_ESP8266
    #define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway1-out"
    #define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway1-in"
    #define MY_MQTT_CLIENT_ID "Gateway"
    #define MY_ESP8266_SSID "BTHub6-36PM"
    #define MY_ESP8266_PASSWORD "88888888"
    #define MY_ESP8266_HOSTNAME "Gateway node"
    #define MY_CONTROLLER_IP_ADDRESS 192, 168, 1,***
    #define MY_IP_GATEWAY_ADDRESS 192,168,1,***
    #define MY_IP_SUBNET_ADDRESS 255,255,255,0
    #define MY_PORT 1883
    #include <ESP8266WiFi.h>
    #include <MySensors.h>

    void setup() {
    }

    void presentation() {
    // Present locally attached sensors here
    }

    void loop() {
    // Send locally attech sensors data here
    }



  • NODE CODE
    #define MY_DEBUG
    #define MY_RADIO_NRF24
    #define MY_NODE_ID 66
    #include <SPI.h>
    #include <MySensors.h>
    #include <Bounce2.h>
    #define RELAY_PIN 7
    #define BUTTON_PIN 6
    #define CHILD_ID 2
    #define RELAY_ON 1
    #define RELAY_OFF 0
    #include <SPI.h>
    #include <avr/wdt.h>
    #include <Wire.h>
    #define RESETWATCHDOG
    Bounce debouncer = Bounce();
    bool state = false;
    bool initialValueSent = false;

    MyMessage msg(CHILD_ID, V_STATUS);

    void setup()
    {
    Serial.begin(115200);
    pinMode(BUTTON_PIN, INPUT_PULLUP);
    debouncer.attach(BUTTON_PIN);
    debouncer.interval(10);
    digitalWrite(RELAY_PIN, RELAY_ON);
    pinMode(RELAY_PIN, OUTPUT);
    }

    void presentation() {
    sendSketchInfo("Grey Lamp", "1.0");
    present(CHILD_ID, S_BINARY);
    }

    void loop()
    {
    wdt_reset();
    if (!initialValueSent) {
    Serial.println("Sending initial value");
    send(msg.set(state ? RELAY_ON : RELAY_OFF));
    Serial.println("Requesting initial value from controller");
    request(CHILD_ID, V_STATUS);
    wait(2000, C_SET, V_STATUS);
    }

    if (debouncer.update()) {
    if (debouncer.read() == LOW) {
    state = !state;
    send(msg.set(state ? RELAY_ON : RELAY_OFF), true);
    }
    }

    }

    void receive(const MyMessage &message) {
    if (message.isAck()) {
    Serial.println("This is an ack from gateway");
    }

    if (message.type == V_STATUS) {
    if (!initialValueSent) {
    Serial.println("Receiving initial value from controller");
    initialValueSent = true;
    }
    state = (bool)message.getInt();
    digitalWrite(RELAY_PIN, !state ? RELAY_ON : RELAY_OFF);
    send(msg.set(state ? RELAY_ON : RELAY_OFF));
    }
    }



  • Hi
    I have different question doesn't this line give you errors?
    persistence_file: '/config/myhouse/mysensors.json



  • SOLVED..... Such a mug, such a small error. One character missing in wireless key.


 

213
Online

8.8k
Users

9.6k
Topics

100.4k
Posts