Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

vfd compressor for heat pump / air conditioner

Giuseppe last edited by

looking for a options to control a heat pump ( driver board).

I have a universal Invertor( INVT from China) with Modbus for compressor and I need a driver board for sensors and Home Assistant integration.

Valden working just with on/off compressors.
Reply Quote 0
1 Reply Last reply
evb last edited by
I'm afraid you're not going to get many answers to your question if you provide not more information...
- type of heat pump, manufacturer
- what are the current possibilities of controlling this heat pump
- photo's
- electric schema's
- ...
Try to give as much as possible (technical) information...
Reply Quote 0
1 Reply Last reply

home assistant 16 modbus 3 vfd compresor 1

2
Posts

21
Views

Log in to reply

Suggested Topics

Help Getting Started
General Discussion • home assistant • • strex

2

0
Votes

2
Posts

842
Views

Hi and welcome! I would say all of the examples in the build section has been converted to 2.0 (except maybe for some old build-projects created by external people). The examples with external library dependencies comes from here: https://github.com/mysensors/MySensorsArduinoExamples/tree/master/examples and standalone examples here: https://github.com/mysensors/MySensors/tree/development/examples
Home Assistant - How to recognize MySensors nodes
Home Assistant • home assistant • • kielnino

64

0
Votes

64
Posts

45951
Views

@Mufasa Yes, you can make custom names and groups of your devices. https://home-assistant.io/getting-started/devices/ Also read the blog post on customizing icons from version 0.8.
Sonoff + MySensors mqtt gateway + Home-Assistant
My Project • mqtt home assistant sonoff • • Efflon

4

3
Votes

4
Posts

7514
Views

Might be helpful for somebody... Things configuration for OpenHab2: Bridge mysensors:bridge-eth:gateway_2 [ ipAddress="192.168.178.50", tcpPort=5003, sendDelay=200, enableNetworkSanCheck=true ] { /** define things connected to that bridge here */ light sonoff01 [ nodeId="0", childId="0", requestAck=true ] }
💬 MDMSPanel "Nextion"
OpenHardware.io • arduino rtc atmega modbus display nextion st485 jtag megacore • • openhardware.io

3

1
Votes

3
Posts

749
Views

@sebdetours said in MDMSPanel "Nextion": Did you take a standart case that you cut out? Hi @sebdetours, yes. This is G1910 (Gainta) box. See drawing attached to projet files.
💬 Leaky - water detector
OpenHardware.io • mqtt esp8266 home assistant water leak • • openhardware.io

5

1
Votes

5
Posts

91
Views

@kimot Thank you for your comment & tips.
Home Assistant v 0.13.1
Home Assistant • switch serial gateway home assistant dimmer light switch • • martinhjelmare

13

1
Votes

13
Posts

5903
Views

I've updated the docs at home-assistant.io with sketch examples. Look at the light example. https://home-assistant.io/components/light.mysensors/#example-sketch It's what I used for testing during development. It adds an RGB sensor/actuator also besides a dimmer, but you can just remove any references to rgb in the sketch. The dimmer slider will only be visible after turning on the light and clicking the entity in the gui to bring up the more info card.
testing with different controllers (mqtt brokers)
Controllers • gateway mqtt home assistant • • OldSurferDude

2

0
Votes

2
Posts

25
Views

@OldSurferDude use a host name for the broker in the configure command (--my-controller-url-address=). Add the host name to /etc/hosts on the rpi where the gateway is. Start the MySensors gatway. When you want to switch brokers, modify /etc/hosts again and restart the MySensors gateway.

20
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1