Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

can't make getStream() work

Mizar03 last edited by

Hi everybody,
I'm new to this forum and here is my first problem. I want to print on the gateway (oled display of my lora ttgo) each payload of incoming messages from nodes. it works when I use getInt() or other getters but it would be easier to do it with getStream() because I read it works with all types of messages. I tryed many things but I'm stucked here and some help would be welcome.
Thanks
Reply Quote 0
1 Reply Last reply

1
Posts

17
Views

Suggested Topics

Day 1 - Status report
Announcements • • hek

3

0
Votes

3
Posts

1510
Views

Feels much faster from here too!
Send 2x relay states to Home Assistant to make them visible?
Troubleshooting • • Matt

15

0
Votes

15
Posts

30
Views

@Matt Yes, the landscape there is incredible. Unfortunately, I mostly have to work when I'm there Where are you from?
Pulse Water Meter, cant see anything
Troubleshooting • • Thib.

4

0
Votes

4
Posts

16
Views

Its seems to be working with this last sketch https://github.com/paolo-rendano/MySensors/blob/c01e14d0942de68126d67325a0687b1a6ce4fa16/examples/WaterMeterPulseSensor/WaterMeterPulseSensor.ino need some time to test it thanks
433MHz amplified (>5V)
Troubleshooting • • andriej

22

0
Votes

22
Posts

11487
Views

Hi, I create a rflink pcb with this schema . I have an emission issue, the module RF 433Mhz Out not have 12v in VOUT+. What could I need to do. This is the pcb design, maybe it needs some improvement. Thanks
Consistent NACK + RPI Gateway
Troubleshooting • • Oumuamua

5

0
Votes

5
Posts

44
Views

Hi all, Should any one need, the fix mentioned in this page actually works. Thanks,
Requesting for help building traffic light led module node
Troubleshooting • • airmedic79

5

0
Votes

5
Posts

40
Views

I am sharing my sketch. Based on the sketch below, I am using this led light to show air quality status (good for green, normal for yellow and bad for red). This sketch is just a switch so you should make some automation in HA. https://www.amazon.com/Traffic-Display-Module-Arduino-Mini-Traffic/dp/B07SZMRSDN #define MY_DEBUG #define MY_RADIO_RF24 #define MY_NODE_ID 16 #define MY_RF24_PA_LEVEL RF24_PA_LOW #include <MySensors.h> #define CHILD_ID_GREEN 1 #define CHILD_ID_YELLOW 2 #define CHILD_ID_RED 3 #define GREEN_PIN 3 #define YELLOW_PIN 4 #define RED_PIN 5 bool greenState = false; bool yellowState = false; bool redState = false; MyMessage msgGreen(CHILD_ID_GREEN, V_LIGHT); MyMessage msgYellow(CHILD_ID_YELLOW, V_LIGHT); MyMessage msgRed(CHILD_ID_RED, V_LIGHT); void setup() { Serial.begin(115200); pinMode(GREEN_PIN, OUTPUT); pinMode(YELLOW_PIN, OUTPUT); pinMode(RED_PIN, OUTPUT); wait(200); } void presentation() { // Initialize the MySensors communication sendSketchInfo("Traffic Light Node", "1.0"); present(CHILD_ID_GREEN, S_LIGHT); present(CHILD_ID_YELLOW, S_LIGHT); present(CHILD_ID_RED, S_LIGHT); } void loop() { // Send initial values of the LEDs to the controller send(msgGreen.set(greenState ? 1 : 0)); send(msgYellow.set(yellowState ? 1 : 0)); send(msgRed.set(redState ? 1 : 0)); // Other tasks in the loop if needed // ... // Add a delay to control how often the initial values are sent delay(5000); // Send initial values every 5 seconds (adjust as needed) } void receive(const MyMessage &message) { // Check which LED to control based on the message received if (message.sensor == CHILD_ID_GREEN && message.type == V_LIGHT) { greenState = !greenState; // Toggle the state digitalWrite(GREEN_PIN, greenState ? HIGH : LOW); // Set the pin accordingly send(msgGreen.set(greenState ? 1 : 0)); // Report back the new state } else if (message.sensor == CHILD_ID_YELLOW && message.type == V_LIGHT) { yellowState = !yellowState; digitalWrite(YELLOW_PIN, yellowState ? HIGH : LOW); send(msgYellow.set(yellowState ? 1 : 0)); } else if (message.sensor == CHILD_ID_RED && message.type == V_LIGHT) { redState = !redState; digitalWrite(RED_PIN, redState ? HIGH : LOW); send(msgRed.set(redState ? 1 : 0)); } }

can't make getStream() work

Suggested Topics

Day 1 - Status report
Announcements • • hek

Send 2x relay states to Home Assistant to make them visible?
Troubleshooting • • Matt

Pulse Water Meter, cant see anything
Troubleshooting • • Thib.

433MHz amplified (>5V)
Troubleshooting • • andriej

Consistent NACK + RPI Gateway
Troubleshooting • • Oumuamua

Requesting for help building traffic light led module node
Troubleshooting • • airmedic79

60
Online

11.0k
Users

11.0k
Topics

112.4k
Posts

can't make getStream() work

Suggested Topics

Day 1 - Status report Announcements • • hek

Send 2x relay states to Home Assistant to make them visible? Troubleshooting • • Matt

Pulse Water Meter, cant see anything Troubleshooting • • Thib.

433MHz amplified (>5V) Troubleshooting • • andriej

Consistent NACK + RPI Gateway Troubleshooting • • Oumuamua

Requesting for help building traffic light led module node Troubleshooting • • airmedic79

60Online

11.0kUsers

11.0kTopics

112.4kPosts

Day 1 - Status report
Announcements • • hek

Send 2x relay states to Home Assistant to make them visible?
Troubleshooting • • Matt

Pulse Water Meter, cant see anything
Troubleshooting • • Thib.

433MHz amplified (>5V)
Troubleshooting • • andriej

Consistent NACK + RPI Gateway
Troubleshooting • • Oumuamua

Requesting for help building traffic light led module node
Troubleshooting • • airmedic79

60
Online

11.0k
Users

11.0k
Topics

112.4k
Posts