Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home

fsgraz last edited by

A simple node to enable/disable the 12V power supply to auxiliary non vital loads (e.g. water boiler) based on the service battery voltage. A relay is controlled by the presence of a charging source.
Additionally, in presence of other charge sources, the Mains Charger is disconnected from the Service Battery. The Mains Charger relay is enabled if there are no other charge sources and the camper is connected to the Shore Power.

There are 2 additional analog voltage input.

I tend to create edge nodes, with full capability of serving the desired use cases, even if Gateway/Controller are down. In this case I can Arm/Disarm some automations from the controller using S_DOOR sensor types.
Reply Quote 2
1 Reply Last reply

1
Posts

22
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
HVAC Controller
My Project • • Michael Link

3

1
Votes

3
Posts

28
Views

We are of like minds, Don't like the cloud based controls (that's another discussion). In my case I have a Bryant/Connex system, heat pump, variable speed fan and 4 zones. There's a lot going on: the 4 zones creates 16 profiles. The fan speed for a profile will depend on the indoor and outdoor temperature. The thermal fluid pump also has to be controlled. A profile will have an optimal air pressure, so there's a sensor there. The controller works just fine not being connected to the cloud. But I want to set the parameters remotely, Bryant/Connex can do this. I also wnat the status of the various actuators and sensors to show up in Home Assistant. The signals sent over the RS422 are proprietary. My plan was to reverse-engineer the signals. After doing this I'll have to experiment to get the right mix of air pressue, fan speed and thermal fluid flow for each profile. I'd like to do the same for my AO Smith heat pump water heater. I'd like to follow your progress. OSD
Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

5

3
Votes

5
Posts

15
Views

@OldSurferDude thank you !
nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

44

18
Votes

44
Posts

8024
Views

The output of the display could also be sent over serial, but the whole idea is you can walk around with the doctor and improve your results as you go.
Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

1

2
Votes

1
Posts

10
Views

No one has replied
Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

1

0
Votes

1
Posts

11
Views

No one has replied

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home

Suggested Topics

Welcome
Announcements • • hek

HVAC Controller
My Project • • Michael Link

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

45
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home

Suggested Topics

Welcome Announcements • • hek

HVAC Controller My Project • • Michael Link

Water Filtering and Sterilization and Hot Water Recirculation My Project • • fsgraz

nRF24Doctor My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway My Project • • fsgraz

Water Meter or "How to get Home Assistant to send saved data to an Arduino" My Project • • OldSurferDude

45Online

11.4kUsers

11.1kTopics

112.7kPosts

Welcome
Announcements • • hek

HVAC Controller
My Project • • Michael Link

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

45
Online

11.4k
Users

11.1k
Topics

112.7k
Posts