Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

PJON and Minicore not working

Trand last edited by

Hello,

I'm encountering an issue with the PJON protocol and the Minicore bootloader on a 328P-PU. The upload works fine, the Atmega starts and tries to connect to the gateway, but nothing comes out of the BUS PIN of the Atmega 328P-PU! The gateway doesn't receive any information.
Using the official NANO bootloader works. I should mention that the setup is on a PCB, so there are no bad connections.
If you have any ideas, I'm open to making it work. Thanks.
Reply Quote 0
1 Reply Last reply

1
Posts

14
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3310
Views

No one has replied
Adding Listen only device to my system.
Development • • dpcons

5

0
Votes

5
Posts

19
Views

@mfalkvidd Thanks for the info!
Gateway without a radio
Development • • OldSurferDude

3

0
Votes

3
Posts

28
Views

@OldSurferDude yes, just run the configure command with --my-transport=none
Radio waking up for no reason.
Development • • Sasquatch

3

0
Votes

3
Posts

37
Views

Over 4 years on, and my node ran continuously sending 4 messages every 5 minutes. It's 700mAh LiFePo4 battery voltage dropped from initial 3.45V to 3.24V, according to LiFePo4 voltge/SoC tables It's just under 40% left. 700*60% = 420mAh. 100 mAH per year. using library 2.40 and blob message I could cut usage to ~25mAh/year, not bad
Saving last known good state, but not in EEPROM
Development • • OldSurferDude

6

0
Votes

6
Posts

33
Views

@OldSurferDude jus request counter states from controller on each reset, worked fine with Domoticz... or save in eeprom but increase location every write, on power up/reset search eeprom for largest value stored and carry on from that location, one long integer will fit 256 times in atmega328(p) eeprom, is that long enough for you ?
Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

3

1
Votes

3
Posts

25
Views

@mfalkvidd Thank you very much, that's exactly what I was looking for!

PJON and Minicore not working

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Adding Listen only device to my system.
Development • • dpcons

Gateway without a radio
Development • • OldSurferDude

Radio waking up for no reason.
Development • • Sasquatch

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

45
Online

11.6k
Users

11.2k
Topics

113.0k
Posts

PJON and Minicore not working

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

Adding Listen only device to my system. Development • • dpcons

Gateway without a radio Development • • OldSurferDude

Radio waking up for no reason. Development • • Sasquatch

Saving last known good state, but not in EEPROM Development • • OldSurferDude

Counting Incoming and Outgoing Messages from a Gateway Development • • Trand

45Online

11.6kUsers

11.2kTopics

113.0kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Adding Listen only device to my system.
Development • • dpcons

Gateway without a radio
Development • • OldSurferDude

Radio waking up for no reason.
Development • • Sasquatch

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

45
Online

11.6k
Users

11.2k
Topics

113.0k
Posts