Multisensor PIR problem [solved]

Sweebee

This can't work well. Your interrupt is set on pin1 - 2 = int-1?

What happens when you remove the pir and use a switch instead?

n3ro

@Sweebee
is #define INTERRUPT PIR_SENSOR_DIGITAL-2 wrong?

when i use a switch it looks OK

rvendrame

@n3ro , what is wrong at your last test? The PIR is reporting 0 and 1, and from time to time there is a temp/hum report as well.

n3ro

@rvendrame in my last test the pir sends endless 0 and dont sleep

rvendrame

Which arduino PIN do you use to connect the PIR?

n3ro

@n3ro said:

#define PIR_SENSOR_DIGITAL 3

:)

rvendrame

Perfect. If it is working fine with a switch --- Maybe your PIN is triggering false positives? Or maybe the PIR output is floating a bit, and arduino is triggering it more than it should?

Sweebee

If a switch works than the only could be the pir itself. You have enabled the pull-up resistor so an open collector should not give floats.

You already told that a sketch with a pir only worked fine?

Well, i can test what happens with my dht22 and a pir tomorrow (with your sketch).

n3ro

@Sweebee thy this would be very nice :)

You find my sketch here:
https://github.com/n3roGit/MySensors_n3ro/tree/master/MotionSensor_DHT_light_battery_mod

BulldogLowell

@n3ro

you are sending an update on the PIR status every time the arduino wakes from a sleep, which you don't need.

Also, and this probably isn't a problem right now, but will case a problem later, use unsigned subtraction in your millis( ) timers

could not see where you were using the library, so I commented it out below, not having it on my computer

I also made a few more notes in the code:

#include <MySensor.h>
//#include <readVcc.h> // cannot see where you are using this library yet
#include <SPI.h>
#include <DHT.h>

#define NODE_ID 10                       // ID of node
unsigned long SLEEP_TIME = 10000UL;        // Sleep time between reports (in milliseconds)

#define CHILD_ID_PIR 1                   // Id of the sensor PIR
#define CHILD_ID_HUM 2                   // Id of the sensor HUM
#define CHILD_ID_TEMP 3                  // Id of the sensor TEMP
#define CHILD_ID_LIGHT 4                 // Id of the sensor LIGHT

#define PIR_SENSOR_DIGITAL 3           // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define INTERRUPT PIR_SENSOR_DIGITAL-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define HUMIDITY_SENSOR_DIGITAL_PIN 2
#define LIGHT_SENSOR_ANALOG_PIN 0

MySensor gw;
// Initialize Variables
MyMessage msgPir(CHILD_ID_PIR, V_TRIPPED);
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
MyMessage msgLight(CHILD_ID_LIGHT, V_LIGHT_LEVEL);

DHT dht;
float lastTemp;
float lastHum;
boolean metric = true;
boolean lastTripped = false;
int oldBatteryPcnt;
int lastLightLevel;
unsigned long mytime;
//int MIN_V = 2700; // empty voltage (0%)
//int MAX_V = 3200; // full voltage (100%)

void setup()
{
  gw.begin(NULL, NODE_ID, false);
  gw.sendSketchInfo("Motion Sensor", "1.0"); // here you call it motion sensor
  pinMode(PIR_SENSOR_DIGITAL, INPUT_PULLUP);
  gw.present(CHILD_ID_PIR, S_MOTION);
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN);
  //gw.sendSketchInfo("Humidity", "1.0"); // here you call it humidity
  gw.present(CHILD_ID_HUM, S_HUM);
  gw.present(CHILD_ID_TEMP, S_TEMP);
  metric = gw.getConfig().isMetric;
  //gw.sendSketchInfo("Light Sensor", "1.0");// pick a name for your sketch, it will only be one
  gw.present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);
}

void loop()
{
  // why send this every time?  
  /*
  boolean tripped = digitalRead(PIR_SENSOR_DIGITAL) == HIGH;
  Serial.print("---------- PIR: ");
  Serial.println(tripped);
  gw.send(msgPir.set(tripped ? "1" : "0"));
  */
  boolean tripped = digitalRead(PIR_SENSOR_DIGITAL) == HIGH;
  if (tripped != lastTripped)  // only need to update controller on a change.
  {
    gw.send(msgPir.set(tripped? "1" : "0"));
    Serial.print("---------- PIR: ");
    Serial.println(tripped? "tripped" : " not tripped");
    lastTripped = tripped;
  }
  if ( millis() - mytime >= SLEEP_TIME )  //use UNSIGNED SUBRTACTION im your millis() timers to avoid rollover issues later on down the line
  {
    float temperature = dht.getTemperature();
    if (isnan(temperature))
    {
      Serial.println("Failed reading temperature from DHT");
    }
    else if (temperature != lastTemp)
    {
      lastTemp = temperature;
      if (!metric) 
      {
        temperature = dht.toFahrenheit(temperature);
      }
      gw.send(msgTemp.set(temperature, 1));
      Serial.print("---------- Temp: ");
      Serial.println(temperature);
    }
    float humidity = dht.getHumidity();
    if (isnan(humidity)) 
    {
      Serial.println("Failed reading humidity from DHT");
    } 
    else if (humidity != lastHum) 
    {
      lastHum = humidity;
      gw.send(msgHum.set(humidity, 1));
      Serial.print("---------- Humidity: ");
      Serial.println(humidity);
    }
    mytime = millis();
  }
  gw.sleep(INTERRUPT, CHANGE, SLEEP_TIME); // Sleep until interrupt detected from motion sensor. Send update every SLEEP_TIME.
}

n3ro

@BulldogLowell

Hey, its a good idea to send only PIR if changed!
The unused code in the sketch is because i have reduced the used functions to the minimum to debug it better. The full sketch has LDR and battery lifetime output too.

i have added some extra output in the modified sketch:

#include <MySensor.h>
//#include <readVcc.h> // cannot see where you are using this library yet
#include <SPI.h>
#include <DHT.h>

#define NODE_ID 10                       // ID of node
unsigned long SLEEP_TIME = 10000UL;        // Sleep time between reports (in milliseconds)

#define CHILD_ID_PIR 1                   // Id of the sensor PIR
#define CHILD_ID_HUM 2                   // Id of the sensor HUM
#define CHILD_ID_TEMP 3                  // Id of the sensor TEMP
#define CHILD_ID_LIGHT 4                 // Id of the sensor LIGHT

#define PIR_SENSOR_DIGITAL 3           // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define INTERRUPT PIR_SENSOR_DIGITAL-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define HUMIDITY_SENSOR_DIGITAL_PIN 2
#define LIGHT_SENSOR_ANALOG_PIN 0

MySensor gw;
// Initialize Variables
MyMessage msgPir(CHILD_ID_PIR, V_TRIPPED);
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
MyMessage msgLight(CHILD_ID_LIGHT, V_LIGHT_LEVEL);

DHT dht;
float lastTemp;
float lastHum;
boolean metric = true;
boolean lastTripped = false;
int oldBatteryPcnt;
int lastLightLevel;
unsigned long mytime;
//int MIN_V = 2700; // empty voltage (0%)
//int MAX_V = 3200; // full voltage (100%)

void setup()
{
  gw.begin(NULL, NODE_ID, false);
  gw.sendSketchInfo("Motion Sensor", "1.0"); // here you call it motion sensor
  pinMode(PIR_SENSOR_DIGITAL, INPUT_PULLUP);
  gw.present(CHILD_ID_PIR, S_MOTION);
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN);
  //gw.sendSketchInfo("Humidity", "1.0"); // here you call it humidity
  gw.present(CHILD_ID_HUM, S_HUM);
  gw.present(CHILD_ID_TEMP, S_TEMP);
  metric = gw.getConfig().isMetric;
  //gw.sendSketchInfo("Light Sensor", "1.0");// pick a name for your sketch, it will only be one
  gw.present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);
}

void loop()
{
  // why send this every time?
  /*
  boolean tripped = digitalRead(PIR_SENSOR_DIGITAL) == HIGH;
  Serial.print("---------- PIR: ");
  Serial.println(tripped);
  gw.send(msgPir.set(tripped ? "1" : "0"));
  */
  boolean tripped = digitalRead(PIR_SENSOR_DIGITAL) == HIGH;
  if (tripped != lastTripped)  // only need to update controller on a change.
  {
    gw.send(msgPir.set(tripped ? "1" : "0"));
    Serial.print("---------- PIR: ");
    Serial.println(tripped ? "tripped" : " not tripped");
    lastTripped = tripped;
  }
  if ( millis() - mytime >= SLEEP_TIME )  //use UNSIGNED SUBRTACTION im your millis() timers to avoid rollover issues later on down the line
  {
    delay(dht.getMinimumSamplingPeriod());
    float temperature = dht.getTemperature();
    if (isnan(temperature))
    {
      Serial.println("Failed reading temperature from DHT");
    }
    else if (temperature != lastTemp)
    {
      lastTemp = temperature;
      if (!metric)
      {
        temperature = dht.toFahrenheit(temperature);
      }
      gw.send(msgTemp.set(temperature, 1));
      Serial.print("---------- Temp: ");
      Serial.println(temperature);
    }
    float humidity = dht.getHumidity();
    if (isnan(humidity))
    {
      Serial.println("Failed reading humidity from DHT");
    }
    else if (humidity != lastHum)
    {
      lastHum = humidity;
      gw.send(msgHum.set(humidity, 1));
      Serial.print("---------- Humidity: ");
      Serial.println(humidity);
    }
    mytime = millis();

  }
  else
  {
    Serial.println("no millis");
  }
  Serial.println(millis());
  Serial.println(mytime);
  Serial.println(SLEEP_TIME);
  gw.sleep(INTERRUPT, CHANGE, SLEEP_TIME); // Sleep until interrupt detected from motion sensor. Send update every SLEEP_TIME.
}

send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
---------- PIR: not tripped
no millis
2185
0
10000
no millis
2189
0
10000
no millis
2193
0
10000
no millis
2195
0
10000
no millis
2197
0
10000
no millis
2201
0
10000
no millis
2203
0
10000
no millis
2205
0
10000
no millis
2209
0
10000
no millis
2211
0
10000
no millis

You can see that the "if millis" will never used .:(

n3ro

i think millis didnt work with sleep. the counter is not increasing when sleeping..

BulldogLowell

@n3ro said:

delay(dht.getMinimumSamplingPeriod());

you dont need this:

delay(dht.getMinimumSamplingPeriod());

since you are sleeping longer than the minimum sampling period

try like this, removing the timer, just use the sleep period t update temp/humidity (untested):

#include <MySensor.h>
//#include <readVcc.h> // cannot see where you are using this library yet
#include <SPI.h>
#include <DHT.h>

#define NODE_ID 10                       // ID of node
unsigned long SLEEP_TIME = 10000UL;        // Sleep time between reports (in milliseconds)

#define CHILD_ID_PIR 1                   // Id of the sensor PIR
#define CHILD_ID_HUM 2                   // Id of the sensor HUM
#define CHILD_ID_TEMP 3                  // Id of the sensor TEMP
#define CHILD_ID_LIGHT 4                 // Id of the sensor LIGHT

#define PIR_SENSOR_DIGITAL 3           // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define INTERRUPT PIR_SENSOR_DIGITAL-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define HUMIDITY_SENSOR_DIGITAL_PIN 2
#define LIGHT_SENSOR_ANALOG_PIN 0

MySensor gw;
// Initialize Variables
MyMessage msgPir(CHILD_ID_PIR, V_TRIPPED);
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
MyMessage msgLight(CHILD_ID_LIGHT, V_LIGHT_LEVEL);

DHT dht;
float lastTemp;
float lastHum;
boolean metric = true;
boolean lastTripped = false;
int oldBatteryPcnt;
int lastLightLevel;
//int MIN_V = 2700; // empty voltage (0%)
//int MAX_V = 3200; // full voltage (100%)

void setup()
{
  gw.begin(NULL, NODE_ID, false);
  gw.sendSketchInfo("Motion Sensor", "1.0"); // here you call it motion sensor
  pinMode(PIR_SENSOR_DIGITAL, INPUT_PULLUP);
  gw.present(CHILD_ID_PIR, S_MOTION);
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN);
  //gw.sendSketchInfo("Humidity", "1.0"); // here you call it humidity
  gw.present(CHILD_ID_HUM, S_HUM);
  gw.present(CHILD_ID_TEMP, S_TEMP);
  metric = gw.getConfig().isMetric;
  //gw.sendSketchInfo("Light Sensor", "1.0");// pick a name for your sketch, it will only be one
  gw.present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);
}

void loop()
{
  // why send this every time?
  /*
  boolean tripped = digitalRead(PIR_SENSOR_DIGITAL) == HIGH;
  Serial.print("---------- PIR: ");
  Serial.println(tripped);
  gw.send(msgPir.set(tripped ? "1" : "0"));
  */
  boolean tripped = digitalRead(PIR_SENSOR_DIGITAL) == HIGH;
  if (tripped != lastTripped)  // only need to update controller on a change.
  {
    gw.send(msgPir.set(tripped ? "1" : "0"));
    Serial.print("---------- PIR: ");
    Serial.println(tripped ? "tripped" : " not tripped");
    lastTripped = tripped;
  }
  float temperature = dht.getTemperature();
  if (isnan(temperature))
  {
    Serial.println("Failed reading temperature from DHT");
  }
  else if (temperature != lastTemp)
  {
    lastTemp = temperature;
    if (!metric)
    {
      temperature = dht.toFahrenheit(temperature);
    }
    gw.send(msgTemp.set(temperature, 1));
    Serial.print("---------- Temp: ");
    Serial.println(temperature);
  }
  float humidity = dht.getHumidity();
  if (isnan(humidity))
  {
    Serial.println("Failed reading humidity from DHT");
  }
  else if (humidity != lastHum)
  {
    lastHum = humidity;
    gw.send(msgHum.set(humidity, 1));
    Serial.print("---------- Humidity: ");
    Serial.println(humidity);
  }
  gw.sleep(INTERRUPT, CHANGE, SLEEP_TIME); // Sleep until interrupt detected from motion sensor. Send update every SLEEP_TIME.
}

n3ro

@BulldogLowell
when i use this sketch the PIR works but the DHT cant read:

Failed reading temperature from DHT
Failed reading humidity from DHT

BulldogLowell

check the connections

n3ro

@BulldogLowell the wires are OK.

In sleep the DHT cant warm-up. so the dht need 2 sec before read. when i dont use the delay i cant read it.

i dont understand why the interrupt didnt work with the enabled delay.

do you have tested on a arduino?

n3ro

https://github.com/n3roGit/MySensors_n3ro/tree/master/MotionSensor_DHT_light_battery_mod

now its working. when i use PIN4 for DHT.:)

rvendrame

@n3ro, i'm glad you fixed it. DHT was on PIN3 before, right? Pin 2 & Pin3 are connected to the interrupts, maybe this was the problem.

n3ro

@rvendrame yes i think so. but now its ok =)

BulldogLowell

@n3ro said:

now its working. when i use PIN4 for DHT.:)

:clap:

Multisensor PIR problem [solved]

8

11.7k

11.2k

113.1k