Help!!! Binary & Relay Compilation Not Working

jeylites

REVISED!!!

Compiles but not working

// Simple binary switch example 
// Connect button or door/window reed switch between 
// digitial I/O pin 3 (BUTTON_PIN below) and GND.

#include <MySensor.h>
#include <SPI.h>
#include <Bounce2.h>
#include <Time.h>        //http://playground.arduino.cc/Code/Time
#include <TimeAlarms.h>  //http://playground.arduino.cc/Code/Time

MySensor gw;

#define RADIO_ID 12
#define noReeds 3
const int BUTTON_PIN[] = {4,5,6};            // Arduino Digital I/O pin for button/reed switch, A0 - A4
boolean reedState[] = {HIGH, HIGH, HIGH};

#define RELAY_1  3  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 1 // Total number of attached relays
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay


Bounce debouncer[noReeds];
MyMessage msg[noReeds];

void setup(){

  gw.begin(NULL, RADIO_ID, true);  //stattc RADIO_ID an enable repeater
  Alarm.delay(250);
  gw.sendSketchInfo("Relay", "1.0");
  gw.sendSketchInfo("Alarm Pannel", "1.0");
  Alarm.delay(250);
  gw.requestTime(receiveTime);
  // initialize Relays with corresponding buttons
  for (int i = 0; i < noReeds; i++){
    msg[i].sensor = i;          // initialize messages
    msg[i].type = V_TRIPPED;
    debouncer[i] = Bounce();        // initialize debouncer
    debouncer[i].attach(BUTTON_PIN[i]);
    debouncer[i].interval(5);
    // Setup the button
    pinMode(BUTTON_PIN[i],INPUT);
    // Activate internal pull-up
    digitalWrite(BUTTON_PIN[i],HIGH);
    gw.present(i, S_DOOR);      // present sensor to gateway
    Serial.print("setup for switch: ");
    Serial.print(BUTTON_PIN[i]);
    Serial.println(" complete" );
    Alarm.timerRepeat(720, updateState); // update relay status every 2 hrs
    Alarm.delay(250);
  }
   // Fetch relay status
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
    // Register all sensors to gw (they will be created as child devices)
    gw.present(sensor, S_LIGHT);
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);   
    // Set relay to last known state (using eeprom storage) 
    digitalWrite(pin, gw.loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}

//  Check if digital input has changed and send in new value
void loop() 
{
  gw.process();
  
}

void incomingMessage(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type==V_LIGHT) {
     // Change relay state
     digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
     // Store state in eeprom
     gw.saveState(message.sensor, message.getBool());
       // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
     
  }  
     
  
  for (int i = 0; i < noReeds; i++){
    debouncer[i].update();
    // Get the update value
    int value = debouncer[i].read();
    if (value != reedState[i]) {
       // Send in the new value
       gw.send(msg[i].set(value==HIGH ? 1 : 0), false);
       reedState[i] = value;
       Serial.print("updating state for swicth: ");
       Serial.print(BUTTON_PIN[i]);
       Serial.print(" state: ");
       Serial.println(reedState[i]);
    }
  }
}

void updateState(){
  Serial.println("Start state info");
  for (int i = 0; i < noReeds; i++)
  {
      Serial.print("sending update for switch: ");
      Serial.println(BUTTON_PIN[i]);
      gw.present(i, S_DOOR);
      Alarm.delay(250);
      //MyMessage msg(relayPin[pin],V_LIGHT);
      gw.send(msg[i].set(reedState[i]), false); // Send last state from eprom to GW
      Alarm.delay(250);
  }
}

// This is called when a new time value was received
void receiveTime(unsigned long time) {
  setTime(time);
}```

sundberg84

On of the error might be the last line "}```)
remove so its only }

Br

BulldogLowell

@jeylites

your example compiles for me.

Consider removing TimeAlarms.h library and use gw.wait(250); instead of Alarm.delay(250);

gw.wait() executes gw.process() over and over again during the delay time; so it is essentially non-blocking.

jeylites

My bad. I copied the wrong sketch to this chat. I have revised the sketch and it complies but it's not working... :( Please see sketch above.

jeylites

This is the serial message I get

repeater started, id 12
send: 12-12-0-0 s=255,c=0,t=18,pt=0,l=5,st=ok:1.4.1
send: 12-12-0-0 s=255,c=3,t=6,pt=1,l=1,st=ok:0
read: 0-0-12 s=255,c=3,t=6,pt=0,l=1:M
send: 12-12-0-0 s=255,c=3,t=11,pt=0,l=5,st=ok:Relay
send: 12-12-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
send: 12-12-0-0 s=255,c=3,t=11,pt=0,l=12,st=ok:Alarm Pannel
send: 12-12-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
send: 12-12-0-0 s=255,c=3,t=1,pt=0,l=3,st=ok:1.0
send: 12-12-0-0 s=0,c=0,t=0,pt=0,l=5,st=ok:1.4.1
setup for switch: 5 complete
send: 12-12-0-0 s=1,c=0,t=3,pt=0,l=5,st=ok:1.4.1
read: 0-0-12 s=255,c=3,t=1,pt=0,l=10:1435918408

BulldogLowell

@jeylites

fyi, just pick one name...

gw.sendSketchInfo("Relay", "1.0");
gw.sendSketchInfo("Alarm Pannel", "1.0");

What is this supposed to be doing? it looks like:

reporting the state of three reed switches
actuating a relay

Why are you using the dalays? time?

hard to really understand what you are trying to do here...

jeylites

@BulldogLowell
Essentially, I will like to combine Array Binary and Relay Actuator in one sketch.

BulldogLowell

three binary switches and a single relay?

jeylites

yes sir !

jeylites

@BulldogLowell

Any ideas how I can get this to work?

Moshe Livne

@jeylites it looks like you are overwriting i somewhere inside the loop. can you try to add prints of the value of i at several strategic points to see when it becomes 5? I would suggest to add one (and also print BUTTON_PIN[i]) before "msg[i].sensor = i;", one after "// Setup the button" and print i with the BUTTON_PIN[i].

jeylites

@Moshe-Livne

I'm going to try fix it as suggested. But the thing is it complies....

Moshe Livne

@jeylites Alas compiling is not a guarantee against memory overwrites....as button_pin should have shown 4 and not 5 i assume that either the index (i) got corrupt or the button_pin array.

BulldogLowell

@jeylites

I think this is what you want. I cannot test it right now, but it does compile:

#include <MySensor.h>
#include <SPI.h>
#include <Bounce2.h>

#define NUMBER_OF_REEDS 3

const int relayPin = 3;
const int reedPin[NUMBER_OF_REEDS] = {4, 5, 6};

int reedState[NUMBER_OF_REEDS];
Bounce debouncer[NUMBER_OF_REEDS] = Bounce();

MySensor gw;
MyMessage msg[NUMBER_OF_REEDS];

void setup()
{
  gw.begin(incomingMessage, AUTO, true);
  gw.sendSketchInfo("Test", "1.0a");
  gw.present(0, S_LIGHT);
  pinMode(relayPin, OUTPUT);
  digitalWrite(relayPin, gw.loadState(0));
  for (int i = 0; i < NUMBER_OF_REEDS; i++)
  {
    debouncer[i].attach(reedPin[i]);
    debouncer[i].interval(5);
    pinMode(reedPin[i], INPUT_PULLUP);
    gw.present(i, S_DOOR);
    gw.wait(250);
  }
}

void loop()
{
  gw.process();
  for (int i = 0; i < NUMBER_OF_REEDS; i++) 
  {
    debouncer[i].update();
    int value = debouncer[i].read();
    if (value != reedState[i]) 
    {
      gw.send(msg[i+1].set(value), false); // device number mismatch here because of the array
      reedState[i] = value;
      Serial.print("updating state for switch: ");
      Serial.print(reedPin[i]);
      Serial.print(" state: ");
      Serial.println(reedState[i]);
    }
  }
}

void incomingMessage(const MyMessage &message)
{
  if (message.type == V_LIGHT)
  {
    int newState = message.getBool();
    digitalWrite(relayPin, newState);
    gw.saveState(0, newState);
    Serial.print(F("Incoming change for relay, New state: "));
    Serial.println(newState);
  }
}

EDIT: Updated to correct debounce class errors

BulldogLowell

@jeylites

to turn relay off automatically after two minutes (and send the updated "off status" to controller... try something like this untested code:

#include <MySensor.h>
#include <SPI.h>
#include <Bounce2.h>

#define NUMBER_OF_REEDS 3

const int relayPin = 3;
const int reedPin[NUMBER_OF_REEDS] = {4, 5, 6};

int reedState[NUMBER_OF_REEDS];
Bounce debouncer[NUMBER_OF_REEDS] = Bounce();

unsigned long relayTimer;

MySensor gw;
MyMessage msg[NUMBER_OF_REEDS];
MyMessage relayMessage(0,V_LIGHT);

void setup()
{
  gw.begin(incomingMessage, AUTO, true);
  gw.sendSketchInfo("Test", "1.0a");
  gw.present(0, S_LIGHT);
  pinMode(relayPin, OUTPUT);
  digitalWrite(relayPin, gw.loadState(0));
  for (int i = 0; i < NUMBER_OF_REEDS; i++)
  {
    debouncer[i].attach(reedPin[i]);
    debouncer[i].interval(5);
    pinMode(reedPin[i], INPUT_PULLUP);
    gw.present(i, S_DOOR);
    gw.wait(250);
  }
}

void loop()
{
  gw.process();
  for (int i = 0; i < NUMBER_OF_REEDS; i++) 
  {
    debouncer[i].update();
    int value = debouncer[i].read();
    if (value != reedState[i]) 
    {
      gw.send(msg[i+1].set(value), false); // device number mismatch here because of the array
      reedState[i] = value;
      Serial.print("updating state for switch: ");
      Serial.print(reedPin[i]);
      Serial.print(" state: ");
      Serial.println(reedState[i]);
    }
  }
  if (millis() - relayTimer > 2 * 60 * 1000UL && digitalRead(relayPin)) // two minute timer
  {
    digitalWrite(relayPin, LOW);
    gw.saveState(0, false);
    gw.send(relayMessage.set(false), true);
  }
}

void incomingMessage(const MyMessage &message)
{
  if (message.type == V_LIGHT)
  {
    int newState = message.getBool();
    digitalWrite(relayPin, newState);
    gw.saveState(0, newState);
    if (newState)
    {
      relayTimer = millis();
    }
    Serial.print(F("Incoming change for relay, New state: "));
    Serial.println(newState);
  }
}

Help!!! Binary & Relay Compilation Not Working

17

11.7k

11.2k

113.1k