Raspbery PI + nrf24 (gpio) not work Domoticz Temp+humanidy PLS HELP

mfalkvidd

Install the gateway:

git clone https://github.com/mysensors/Raspberry.git
cd Raspberry/librf24-bcm
make all && sudo make install
cd ..
make all && sudo make install
sudo make enable-gwserial
sudo /etc/init.d/PiGatewaySerial start

Verify that the gateway started properly:

cat /dev/ttyMySensorsGateway
0;0;3;0;14;Gateway startup complete.

Domoticz is unable to read from /dev/ttyMySensorsGateway so create a link to a name that Domoticz understands:

sudo ln -s /dev/ttyMySensorsGateway /dev/ttyUSB20

To automatically create the link on startup, add

ln -s /dev/ttyMySensorsGateway /dev/ttyUSB20

just before

exit0

in /etc/rc.local

I then added the gateway as per the image in my last post.

EDIT: Changed instructions to use librf24-bcm instead of tmrh20. tmrh20 tricked my Gateway into forwarding everything to a strange (non-existing) parent node.

wergeld

@mfalkvidd I am attempting to follow your lead here on compiling the Raspberry mysensors gateway. However, this is failing on my rpi2 with tons of repeating errors like:
bcm2835.c: In function "bcm2835_init" :
error invalid suffix "x" on integer constant

I have enabled SPI from rasp-config. This is using the domoticz image of raspbian wheezy. Any thoughts on how to get around this?

mfalkvidd

@wergeld I remember seeing those errors as well. I think that's why I switched to tmrh20 but then I switched back and didn't get any errors when I tried again. Not sure what happened between, I hacked away now and then during several weeks.

wergeld

@mfalkvidd Okay, that is what i was going to go for as well:
Try tmrh20 and then see what happens.

I think there is some issue with the code in general as the rpi2 does not have the bcm2835 chip, right? I think it is bcm2836 (mind not working this early in the morning).

mfalkvidd

Looks like it. Output from hwinfo:

raspberrypi-firmware: /devices/platform/soc/soc:firmware
    bcm2835-mbox: /devices/platform/soc/3f00b880.mailbox
    bcm2835_AUD0: /devices/platform/bcm2835_AUD0.0
    bcm2835_AUD0: module = snd_bcm2835
    bcm2835_AUD1: /devices/platform/bcm2835_AUD1.1
    bcm2835_AUD1: module = snd_bcm2835
    bcm2835_AUD2: /devices/platform/bcm2835_AUD2.2
    bcm2835_AUD2: module = snd_bcm2835
    bcm2835_AUD3: /devices/platform/bcm2835_AUD3.3
    bcm2835_AUD3: module = snd_bcm2835
    bcm2835_AUD4: /devices/platform/bcm2835_AUD4.4
    bcm2835_AUD4: module = snd_bcm2835
    bcm2835_AUD5: /devices/platform/bcm2835_AUD5.5
    bcm2835_AUD5: module = snd_bcm2835
    bcm2835_AUD6: /devices/platform/bcm2835_AUD6.6
    bcm2835_AUD6: module = snd_bcm2835
    bcm2835_AUD7: /devices/platform/bcm2835_AUD7.7
    bcm2835_AUD7: module = snd_bcm2835
      alarmtimer: /devices/platform/alarmtimer
         dwc_otg: /devices/platform/soc/3f980000.usb
     spi-bcm2835: module = spi_bcm2835
     spi-bcm2835: /devices/platform/soc/3f204000.spi
      bcm2708_fb: /devices/platform/soc/soc:fb
bcm2708-dmaengine: /devices/platform/soc/3f007000.dma
 uio_pdrv_genirq: module = uio_pdrv_genirq
      serial8250: /devices/platform/serial8250
 pinctrl-bcm2835: /devices/platform/soc/3f200000.gpio
     mmc-bcm2835: /devices/platform/soc/3f300000.mmc
         arm-pmu: /devices/platform/soc/soc:arm-pmu
 bcm2835_thermal: /devices/platform/soc/soc:thermal
   bcm2835_vchiq: /devices/platform/soc/3f00b840.vchiq
     bcm2708_i2c: /devices/platform/soc/3f804000.i2c
     bcm2708_i2c: module = i2c_bcm2708

mfalkvidd

This thread might be useful for troubleshooting

wergeld

@mfalkvidd Yes, I used that to do the build initially. I cannot even get past the "make" command (tried sudo make as well). One person there had same error but they "solved it" and did not mention how they did it. I am going to give it another go tonight with a fresh image of raspbian.

wergeld

Finally got mysensors built on my RPi2. And have built domoiticz and it is up and running! I have added my USB gateway but now not sure what to do? It does not appear to pick up my sensor node. Where do I change the Gateway's channel and radio parameters?

wergeld

Actually forgot that MyConfig file when I built the RPi gateway. That is all set but now when I debug using ./PiGatewaySerial i see good output for the radio parameters but then it spits out continuous reams of:

read: 0-0-0 s=0,c=0,t=0,pt=0,l=0:
version mismatch
read: 0-0-0 s=0,c=0,t=0,pt=0,l=0:
version mismatch
read: 0-0-0 s=0,c=0,t=0,pt=0,l=0:
version mismatch

Not sure what this is about as I do not have any nodes on this channel (76). All my active nodes are on channel 90 and are talking just fine to my RPi running easyIOT server.

What is this version mismatch about?

GertSanders

Probably your nodes which were compiled with version 1.5 of the library, and the fact that the version of the library upon which the PiGatewaySerial is compiled is still version 1.4

On your Raspberry, in the Raspberry directory you should find a "Version.h" file.

Try changing the content to this:
/***

This file defines the Sensor library version number
Normally, contributors should not modify this directly
as it is manaaged by the MySensors Bot.
*/
#ifndef Version_h
#define Version_h

#define LIBRARY_VERSION "1.5"

#endif

The do another sudo make etc...

I hope this helps you.

wergeld

GertSanders,
All of my nodes are using 1.4 library. Oddly at around 2:30 am my one sensor I moved to same channel as my domoticz gateway got picked up. Pretty interesting! I had changed it to the domiticz channel at 11pm. Progress is good. Now going to see about why the temp is being reported as ~140 F when that sensor reported ~70 F (correct) when attached to my other controller.

tommyken

@mfalkvidd said:

Install the gateway:
git clone https://github.com/mysensors/Raspberry.git
cd Raspberry/librf24-bcm
make all && sudo make install
cd ..
make all && sudo make install
sudo make enable-gwserial
sudo /etc/init.d/PiGatewaySerial start
Verify that the gateway started properly:
cat /dev/ttyMySensorsGateway
0;0;3;0;14;Gateway startup complete.
Domoticz is unable to read from /dev/ttyMySensorsGateway so create a link to a name that Domoticz understands:
sudo ln -s /dev/ttyMySensorsGateway /dev/ttyUSB20
To automatically create the link on startup, add
ln -s /dev/ttyMySensorsGateway /dev/ttyUSB20
just before
exit0
in /etc/rc.local

I then added the gateway as per the image in my last post.

EDIT: Changed instructions to use librf24-bcm instead of tmrh20. tmrh20 tricked my Gateway into forwarding everything to a strange (non-existing) parent node.

I tried this for SPI through raspberry

Can someone provide me the correct way to install those ?

First attempt was like mentioned above. But i don't have the folder librf24-bcm

then i placed nrf2401 zip file into the folder from http://tmrh20.github.io/

Now i got this error

pi@testdom ~/Raspberry $ make all
g++ -c -o MyGateway.o MyGateway.cpp -Wall -Ofast -mfpu=vfp -lpthread -g -D__Raspberry_Pi -mfloat-abi=hard -mtune=arm1176jzf-s -D_TTY_NAME="/dev/ttyMySensorsGateway" -D_TTY_GROUPNAME="tty" -march=armv6zk -D__PI_BPLUS -I. -I/usr/local/include/RF24
In file included from RF24.h:18:0,
from MySensor.h:37,
from MyGateway.h:16,
from MyGateway.cpp:13:
RF24_config.h:38:32: fatal error: utility/includes.h: No such file or directory
#include "utility/includes.h"
^
compilation terminated.
Makefile:57: recipe for target 'MyGateway.o' failed
make: *** [MyGateway.o] Error 1

I have lateste update and upgrade and i'm using Jessie. Hopely can someone help me.

Thanks in advance.

mfalkvidd

@tommyken see the updated instructions at http://forum.mysensors.org/topic/2437/step-by-step-procedure-to-connect-the-nrf24l01-to-the-gpio-pins-and-use-the-raspberry-as-a-serial-gateway They show how to get the rf24 files.

Raspbery PI + nrf24 (gpio) not work Domoticz Temp+humanidy PLS HELP

14

11.7k

11.2k

113.1k