Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

any can help me? arduino code for washing machine stop when overload using weight sensor

Cin last edited by

any can help me? arduino code for washing machine stop when overload using weight sensor
Reply Quote 0
1 Reply Last reply
Tmaster last edited by Tmaster

what is a weight sensor,and where you put this?

There are weight overload in a washing machine? my machine only stops if the weight is not centered, because it start to jumping
Reply Quote 0
1 Reply Last reply
RJ_Make Hero Member last edited by

I think a vibration sensor may work better in this case, and there are examples.
Reply Quote 0
1 Reply Last reply

3
Posts

1744
Views

Log in to reply

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Interface-board-for-remote-control
My Project • • OldSurferDude

2

1
Votes

2
Posts

22
Views

That is a well documented project. Much appreciated
BT832X PA / LNA
My Project • • nagelc

1

0
Votes

1
Posts

12
Views

No one has replied
Wio-E5 (STM32 and SX1262)
My Project • • nagelc

2

1
Votes

2
Posts

27
Views

Quick Range Check on the WIO-E5-LE. The LE version uses only the low power PA, +14dBm max. Using the default settings except for 915MHz #define MY_SX126x_FREQUENCY (SX126x_915MHZ) #define MY_SX126x_LORA_SF LORA_SF7 #define MY_SX126x_LORA_BW LORA_BW_125 #define MY_SX126x_LORA_CR LORA_CR_4_5 I get about 190 meter range, just walking around the neighborhood, line of site except for some trees and power lines. No tuning on the antenna. Just using a 77.9mm wire. Not as dramatic as some have achieved with LoRa radio's, but plenty good enough for my house and yard : )
Door chime
My Project • • Paul Scarbro

2

0
Votes

2
Posts

23
Views

@Paul-Scarbro There are multitude of solution, but since we are in MySensors Land, let's do a MySensors solution. You'll quickly see that doing that adds a lot of overhead. We'll use an Arduino Nano or RF Nano if you're going to go whole hog. It can be run from 3.3V or 5V DC, not AC. The reed switch would be connected to an input of the Nano and one of the outputs would drive a relay. The relay would drive the chime. Your C++ program would be something like: #define inputButton 2; // connect reed switch here #define outputRelay 4; // connect relay to this pin see MySensors Relay example #define RELAY_ON 1 // GPIO value to write to turn on attached relay #define RELAY_OFF 0 // GPIO value to write to turn off attached relay void setup() { pinmode(inputButton,INPUT); pinmode(outputRelay,OUTPUT); // put your setup code here, to run once: } void loop() { // put your main code here, to run repeatedly: if (digitalRead(inputButton) == 0) { digitalWrite(outputRelay,RELAY_ON); wait(2000); // wait 2 seconds digitalWrite(outputRelay,RELAY_OFF); // now wait for door to close while(digitalRead(inputButton) == 0) ; //does nothing until reed switch opens } } There are some subtleties that I may have glossed over, but this is the gist. By looking at the MySensors Relay example, you'll see how to integrate this into a MySensors environment. That's where you'd want to get the RF Nano. I've made the assumption you're familiar with the Arduino IDE and you've looked into the MySensors environment.
Simulate Online-Recreating 'Flappy Bird' with Arduino Nano
My Project • • Skylar Jones

1

0
Votes

1
Posts

17
Views

No one has replied

16
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1