Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

any can help me? arduino code for washing machine stop when overload using weight sensor

Cin last edited by

any can help me? arduino code for washing machine stop when overload using weight sensor
Reply Quote 0
1 Reply Last reply
Tmaster last edited by Tmaster

what is a weight sensor,and where you put this?

There are weight overload in a washing machine? my machine only stops if the weight is not centered, because it start to jumping
Reply Quote 0
1 Reply Last reply
RJ_Make Hero Member last edited by

I think a vibration sensor may work better in this case, and there are examples.
Reply Quote 0
1 Reply Last reply

3
Posts

1744
Views

Log in to reply

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

2

2
Votes

2
Posts

35
Views

@Kokosnoot good solution. I remember the discussion in the early days of MySensors. I've powered the radio's for most of my sensors from the 3.3v regulator on the arduino board and for me that works perfect. But for my latest designs I decided to add a separate ams regulator for my radio's like the guys suggested in the beginning. Because you basically want the on board regulator to power the mcu only.
Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

1

0
Votes

1
Posts

12
Views

No one has replied
Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

5

3
Votes

5
Posts

15
Views

@OldSurferDude thank you !
Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

90

7
Votes

90
Posts

73900
Views

Hello everyone, Firstly, I apologize for reviving such an old thread, but I find myself in a unique situation and was hoping some of you might be able to help. I hope everyone's doing well. I have a specific inquiry that I couldn't find a recent solution for. Does anyone here know of a tool to generate "fake" Dooya remote (DC90) RF codes for curtains? I've acquired a few motors without controllers and am trying to integrate them with Home Assistant and Bradlink RF remote. Specifically, I'm searching for a way to generate codes for the Up, Down, Stop, and the "Set" button functions to configure curtain limits. Any insights or guidance would be immensely appreciated. Thank you so much in advance!
HVAC Controller
My Project • • Michael Link

3

1
Votes

3
Posts

28
Views

We are of like minds, Don't like the cloud based controls (that's another discussion). In my case I have a Bryant/Connex system, heat pump, variable speed fan and 4 zones. There's a lot going on: the 4 zones creates 16 profiles. The fan speed for a profile will depend on the indoor and outdoor temperature. The thermal fluid pump also has to be controlled. A profile will have an optimal air pressure, so there's a sensor there. The controller works just fine not being connected to the cloud. But I want to set the parameters remotely, Bryant/Connex can do this. I also wnat the status of the various actuators and sensors to show up in Home Assistant. The signals sent over the RS422 are proprietary. My plan was to reverse-engineer the signals. After doing this I'll have to experiment to get the right mix of air pressue, fan speed and thermal fluid flow for each profile. I'd like to do the same for my AO Smith heat pump water heater. I'd like to follow your progress. OSD

2
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1