💬 Roller Shutter Node

[Nca78]

@scalz in fact je suis Français ;)
Do you think you can have one board ready in around a month time ? I'll have family coming from France at the end of september so I can give you an address in France where to send the board :)

I'm pretty sure I'll be ok with smd after some time, but I'm just not ready yet. I have bought some kits to train before I try before I do it on real boards/components.

[scalz]

@Nca78 hehe. that's what I thought first time i saw your nick, don't tell me why maybe the 78 :) that's fun.

I will see. this is nrf24 board you want, isn't it? I have no of these in stock but I have an order of multiple pcb to do this week. so I will buy a set. I will use DHL..not so patient when there are new boards to try :) So I will tell you what I can do..

[Nca78]

@scalz If you are not ready with the NRF24 version I will be fine with a RFM version, I'll just build a RFM gateway it's not a big deal, and I'll have no excuse not to try all those nice boards with RFM69 that are on openhardware ;)

[scalz]

nrf24 smd version is uploaded. Have fun

[fets]

@scalz I'm another one from France and very interessing in pcba version with rfm69 cause sma is not my cut of tea :).
Anyway thank for your work and ideas,

[scalz]

@fets cool. About PCBA, for the moment; it's on fabhouse hand, I'm waiting for the quotation, and if everything goes well, this board may become a part of Mysensors project, meaning supporting Mysensors, I'm very glad :)

[coxifred]

@Scalz : Hello, what a great job ! it's exactly the thing i'm trying to do since few months. But severe issues with relay and my 220v rolling shutters. Actually, the relays freeze sometimes and stay glue to a position. I read a lot about the inductive load and snubber, but i'm a newbie with electronics. I tried differents relays : from blue one classic to APF30205, but always fails.
Did you encounter problem with your OMRON G5Q ? Is the varistor the solution or it's only for other purpose (security,...). Here is my project https://github.com/coxifred/PimpMyCeliane/wiki
Thanks for you response, and congratulations (twice).

[scalz]

@coxifred
Hello. sorry for delay..busy time..
I already did my design when I saw your build. But I preferred to not use wifi for rollershutter..

If you're newbie in electronics, be careful with AC and your motors ;)

• I don't see any safety on your build..
• seems your relays are in //, so not interlocked. Better in serie, so you can't do UP & DOWN at same time. Not a problem in software, but if parasitic problems, then it could happen.

I have no problem with my relays but I have only tried on a somfy motor, and another old blind motor.

Relay can stay glued because of multiple reasons, not easy to debug at distance ;)

• EMI parasites etc... esp8266, especially nodemcu module could be sensitive. And lot of wire etc near AC lines etc is a nasty combo. this would not pass EMI tests!
• So, at relay input : EMI for instance or, I don't know if your relay module has this, but that's better to use relay driver or at least some diode. . It can avoid improves false things on relay input.
• If you're sure you have no problem on relay driver/transistor side, then it can be at output. It can be stayed glue in inductive overload for instance. If bad quality relay. If relay is good quality. Perhaps you need an additional snubber. Which is why I have oversized my relays (10Amp).

Maybe I have missed few others points, but I hope that will help you :)

[coxifred]

@scalz : Thanks for your response. For me all eletronic/software before output is ok. I tried with simple bulbs, works every time, no glue. The problem appears only with rolling shutter motors (wich are not somfy, but 220v). I think i need a snubber (for inductive overload ) but don't know how to wire it at the output, and wich model. I'll buy your relay model and test again. Perhaps i was not lucky with my relay. I even buyed a Chacon/DIO (433) rolling shutter module to see what kind of relay are they using. I have to take a voltage measure on the (chacon) input's relay, not node, too much time:)
Thanks 4 your response.

[tonnerre33]

Hello,

The PCB order link is for nrf24 or RFM69 version ?

Edit :

omg, i see the answer in the first page ^^ it's for RFM69 version .

When will you give the link for order PCB with nrf 24 ?

[tonnerre33]

Hello,

Where can we found the program (.ino) for this board ?

Thx

[Takero]

Where can i find the example sketch?

[Fabien]

There is no official sketch avaiable at this moment. And @scalz is working hard on RFM69 ... I began yesterday to write a new sketch, I will publish in few days (weeks ?).

[scalz]

Why do you want an example sketch ?
hmm..my precious sketch :stuck_out_tongue:
@Fabien is right that's quite busy days :)
I didn't published it yet because i prefer release when it's polished as i like..
Well, as Fabien is a betatester ;)
i've published a pre beta version! on my git https://github.com/scalz/MySensors-HW/tree/development/RollerShutterNode/FW/MyRollershutter

BUT i'm actually busy so i won't have time for support on setup. i think it's enough documented for the moment.
I prefer to tell this than giving hope..better like this. I learnt this from a smart guy recently :pray:

That said i hope you will have fun! and i will try to update as i can..you've not seen the new version of this board :yum:

[Takero]

Hey, no Problem :-)

I just ask for it, as you write it is in the examples folder ;-)

Thanks for the pre Beta, i will work on it :+1:

[tonnerre33]

@scalz Thanks for the pre beta sketch.
i have searched the sketch many times in the example folder too :) But no examples folder find ;)
I have posted some pictures of the pcb here i fyou want to see:

http://www.photorapide.com/albums/jordan/khjept/circuit-pcb-roller-shutter-node.html

[Takero]

Hey Scalz, u have forgotten to connect the CSN - Pin in your PCB file for NRF24 ;-) I just solder a bridge between NRF Pin 4 and R14

[scalz]

@takero
thx for reporting!
i'm using rfm69, argh. i will take a look asap.

[Takero]

Yah, i know, take it easy this is an minor bug :-)
Your misstake is in the schematic, your wire on the NRF24 CSN-PIN is unnamed.

For feature Update, it is advisable to plug an ELKO ~400-500uF near the NRF24 Power, i have reciving problems whith "RF24_PA_HIGH" but i need hight for the distance.

[scalz]

@Takero

But it was named! or the pullup resistor would not be wired, and it was also present on atmel.. and no airwire, weird!
well, i think it happened during converstion to nrf24.
Hopefully the pullup resistor is just near the radio!

Is RF24_PA_HIGH available for nrf24 smd, i thought this was for High power nrf. i'm certainly wrong..I've no problem with rfm though.

I don't think i will do more, unfortunately, I mean in this case, it's sort of double job, and i'm using rfm69.
but when i can, i put rfm69 and nrf footprint (i have a pcb not released like this, not a shutter node).

Now it's updated :) rev=1.3a for nrf
See you soon